ETSI EN 301 489-12-2008 Electromagnetic compatibility and Radio spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Part 12 Specifi.pdf

《ETSI EN 301 489-12-2008 Electromagnetic compatibility and Radio spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Part 12 Specifi.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 301 489-12-2008 Electromagnetic compatibility and Radio spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Part 12 Specifi.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI EN 301 489-12 V2.2.2 (2008-09)Harmonized European Standard (Telecommunications series) Electromagnetic compatibilityand Radio spectrum Matters (ERM);ElectroMagnetic Compatibility (EMC)standard for radio equipment and services;Part 12: Specific conditions for Very Small ApertureTerminal, Satell

2、ite Interactive Earth Stations operatedin the frequency ranges between 4 GHz and 30 GHzin the Fixed Satellite Service (FSS)ETSI ETSI EN 301 489-12 V2.2.2 (2008-09) 2 Reference REN/ERM-EMC-265-12 Keywords earth station, EMC, FSS, radio, regulation, satellite, SNG, testing, VSAT ETSI 650 Route des Luc

3、ioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: htt

4、p:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the p

5、rinting on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at htt

6、p:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright an

7、d the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2008. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM is a Trade Ma

8、rk of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI EN 301 489-12 V2.2.2 (2008-09) 3 Contents Intellectual Property Rights5 Foreword.5 1 Scope 6 2 References 6 2.1 Normative references .6 2.2 Informative references7 3 Definitions and abbreviations.

9、7 3.1 Definitions7 3.2 Abbreviations .7 4 Test conditions .8 4.1 General .8 4.2 Arrangements for test signals .8 4.2.1 Arrangements for test signals at the input of transmitters.8 4.2.2 Arrangements for test signals at the output of transmitters.8 4.2.3 Arrangements for test signals at the input of

10、receivers .9 4.2.4 Arrangements for test signals at the output of receivers .9 4.2.5 Arrangements for testing transmitter and receiver together (as a system) 9 4.3 Exclusion bands9 4.4 Narrow band responses of receivers.9 5 Performance assessment.9 5.1 General .9 5.2 Equipment configuration(s)9 5.3

11、Equipment classification 10 6 Performance criteria .11 6.1 Performance criteria (C) for Continuous phenomena applied to the EUT .11 6.2 Performance criteria (TA) for Transient phenomena applied to a grade A EUT11 6.3 Performance criteria (TB) for Transient phenomena applied to a grade B EUT12 7 Appl

12、icability overview.12 7.1 Emission.12 7.1.1 General12 7.1.2 Special conditions.12 7.2 Immunity 12 7.2.1 General12 7.2.2 Special conditions.13 Annex A (normative): Definitions of Satellite Earth Stations (ES) within the scope of the present document.14 A.1 Transmit only and Transmit and receive Ku ba

13、nd VSATs 14 A.2 Receive-only Ku band VSATs.14 A.3 Transmit only and Transmit and receive C band VSATs.15 A.4 Receive-only C band VSATs .15 A.5 Satellite News Gathering (SNG) Ku band Transportable Earth Stations (TESs).16 A.6 Satellite Interactive Terminals (SITs) 17 A.7 Satellite User Terminals (SUT

14、s) transmitting in the frequency range 29,5 GHz to 30,0 GHz 17 A.8 Satellite User Terminals (SUTs) transmitting in the frequency range 27,5 GHz to 29,5 GHz 18 A.9 Satellite Earth Station on Trains (EST) transmitting in the frequency range 14,0 GHz to 14,5 GHz19 ETSI ETSI EN 301 489-12 V2.2.2 (2008-0

15、9) 4 Annex B (informative): Bibliography.20 Annex C (informative): The EN title in the official languages .21 History 22 ETSI ETSI EN 301 489-12 V2.2.2 (2008-09) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The informa

16、tion pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ET

17、SI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000

18、 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). Th

19、e present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Directive 98/34/EC i.2 (as amended) laying down a procedure for the provision of information in the field of technical standards and regulations. The present document, together wit

20、h EN 301 489-1 1, is intended to become a Harmonized Standard, the reference of which will be published in the Official Journal of the European Communities referencing the Directive 1999/5/EC i.1 of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications

21、terminal equipment and the mutual recognition of their conformity (“the R - for informative references. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. For online referenced documents, information sufficien

22、t to identify and locate the source shall be provided. Preferably, the primary source of the referenced document should be cited, in order to ensure traceability. Furthermore, the reference should, as far as possible, remain valid for the expected life of the document. The reference shall include th

23、e method of access to the referenced document and the full network address, with the same punctuation and use of upper case and lower case letters. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity. 2.1 Normative r

24、eferences The following referenced documents are indispensable for the application of the present document. For dated references, only the edition cited applies. For non-specific references, the latest edition of the referenced document (including any amendments) applies. 1 ETSI EN 301 489-1 (V.1.8.

25、1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements“. ETSI ETSI EN 301 489-12 V2.2.2 (2008-09) 7 2.2 Informative references The following referenced documents are not

26、 essential to the use of the present document but they assist the user with regard to a particular subject area. For non-specific references, the latest version of the referenced document (including any amendments) applies. i.1 Directive 1999/5/EC of the European Parliament and of the Council of 9 M

27、arch 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R b) the specific Quality of Transmission Measurement Apparatus (QTMA). For the measurement of the quality of transmission a communications link shall be established and the wanted

28、input signal shall be applied to the Radio Frequency (RF) input of the receiver via the antenna. The special test equipment, the QTMA and the source of the wanted input signal shall be located outside the test environment. Adequate measures shall be taken to protect them from the effects of all the

29、radiated fields within the test environment. 4.2.1 Arrangements for test signals at the input of transmitters The provisions of EN 301 489-1 1, clause 4.2.1 shall apply. 4.2.2 Arrangements for test signals at the output of transmitters The provisions of EN 301 489-1 1, clause 4.2.2 shall apply. ETSI

30、 ETSI EN 301 489-12 V2.2.2 (2008-09) 9 4.2.3 Arrangements for test signals at the input of receivers The provisions of EN 301 489-1 1, clause 4.2.3 shall apply with the following modification. For tests on the receiver, the level of the signal received from the test transmitter shall be as close as

31、possible to the normal operation level of the EUT receiver. 4.2.4 Arrangements for test signals at the output of receivers The provisions of EN 301 489-1 1, clause 4.2.4 shall apply. 4.2.5 Arrangements for testing transmitter and receiver together (as a system) The provisions of EN 301 489-1 1, clau

32、se 4.2.5 shall apply. 4.3 Exclusion bands There are no exclusion bands for ESs within in the scope of the present document. 4.4 Narrow band responses of receivers Narrow band responses are not allowed for ESs within in the scope of the present document. 5 Performance assessment 5.1 General The provi

33、sion of EN 301 489-1 1, clause 5.1 shall apply. In addition the manufacturer shall provide the following information to be recorded in the test report: - the dedicated grade (A or B) for the ES in accordance with the information contained in the instructions accompanying the ES (see clause 5.3); - t

34、he ranges of the operational parameters, e.g. the power delivered to the antenna, the frequency ranges; - the minimum quality of transmission, and the method to be used to assess it. This information shall be in accordance with the documentation accompanying the equipment. 5.2 Equipment configuratio

35、n(s) For radiation measurements in carrier-on state, the ES shall be put in a continuous transmit mode or to the maximum burst rate where applicable. The ES shall be operated at the highest normal operating Equivalent Isotropically Radiated Power (EIRP) or, if that is the maximum attainable, then 3

36、dB below such maximum. A suggested test configuration is shown in figure 1. ETSI ETSI EN 301 489-12 V2.2.2 (2008-09) 10Figure 1: Suggested test configuration For the tests, the ES antenna reflector and the test antenna may be removed at their flanges and be replaced by one direct wave guide connecti

37、on. The following test equipment shall be the means whereby the correct operation of the EUT is verified: a) the power meter measures the output power and is used to confirm the transmission disabled, carrier-on and carrier-off states and output level consistency; b) the frequency counter measures t

38、he centre frequency of the radiated carrier in the absence of modulation; c) the spectrum analyser measures the bandwidth of the transmission; d) the test receiver is used to demodulate the transmitted signal; e) the two QTMA are used in conjunction with each other to assess the quality of transmiss

39、ion; f) the test transmitter is used to control the switching between transmission disabled, carrier-on and carrier-off states by transmitting the control and monitoring signals. 5.3 Equipment classification The provisions of EN 301 489-1 1, clause 5.5 set out for base stations shall apply with the

40、following addition. The equipment are classified into the two grades of service: - grade A of ES for which short interruptions of transmission are accepted during immunity testing with EMC transient phenomena; - grade B of ES for which no short interruption of transmission is accepted during immunit

41、y testing with EMC transient phenomena. The applicable grade A or B shall be declared by the manufacturer, it shall be in accordance with the information contained in the instructions accompanying the ES, and shall be recorded in the test report. ETSI ETSI EN 301 489-12 V2.2.2 (2008-09) 116 Performa

42、nce criteria The definition of the functions of the EUT, including its ancillary equipment, to be checked during and after the EMC tests shall be declared by the manufacturer and recorded in the test report. The equipment shall meet the minimum performance criteria as specified in clauses 6.1, 6.2 a

43、nd 6.3 and additionally the functions as declared by the manufacturer. 6.1 Performance criteria (C) for Continuous phenomena applied to the EUT The provisions of EN 301 489-1 1, clause 6.1 shall apply with the following modification. The EUT shall be considered to satisfy the immunity if the followi

44、ng conditions are met during and after the exposure: a) the quality of transmission observed is no worse than that declared by the manufacturer (clause 5.1); b) the EUT is able to be placed in the transmission disabled state, and does not leave that state without being commanded; c) when the EUT is

45、in the transmission disabled state there is no change in the signal level; d) when the EUT is in the carrier-on state there is no change in the signal level or frequency; e) when the EUT is in the carrier-off state there is no increase of the signal level; f) for ESs capable of transmitting, under n

46、o circumstances does the transmitter operate unintentionally during the test; g) the EUT operates as intended with no loss of user control functions, stored data and the communications link. 6.2 Performance criteria (TA) for Transient phenomena applied to a grade A EUT The provisions of EN 301 489-1

47、 1, clause 6.2 shall apply with the following modification. The EUT shall be considered to satisfy the immunity specifications if the following conditions are met: - during and after the series of individual exposures: a) the EUT is able to be placed in the transmission disabled state, and does not

48、leave that state without being commanded; b) when the EUT is in the transmission disabled state there is no change in the signal level; c) when the EUT is in the carrier-on state there is no change in the signal frequency or increase of the signal level; d) when the EUT is in the carrier-off state t

49、here is no increase of the signal level; e) for ESs capable of transmitting, under no circumstances does the transmitter operate unintentionally during the test; - at the conclusion of each exposure the quality of transmission observed shall be no worse than that declared by the manufacturer (clause 5.1); - at the conclusion of the total test comprising the series of individual exposures the EUT shall operate as intended with no loss of user control functions or stored data and the communications link shall remain maintained. ETSI ETSI EN 301 489-12