EN ISO 19085-2-2017 en Woodworking machines - Safety - Part 2 Horizontal beam panel circular sawing machines.pdf

《EN ISO 19085-2-2017 en Woodworking machines - Safety - Part 2 Horizontal beam panel circular sawing machines.pdf》由会员分享，可在线阅读，更多相关《EN ISO 19085-2-2017 en Woodworking machines - Safety - Part 2 Horizontal beam panel circular sawing machines.pdf（50页珍藏版）》请在麦多课文档分享上搜索。

1、Woodworking machines - SafetyPart 2: Horizontal beam panel circular sawing machines (ISO 19085-2:2017)BS EN ISO 19085-2:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 19085-2 August 2017 ICS 13.110; 79.120

2、.10 English Version Woodworking machines - Safety - Part 2: Horizontal beam panel circular sawing machines (ISO 19085-2:2017) Machines bois - Scurit - Partie 2: Scies circulaires panneaux horizontales presseur (ISO 19085-2:2017)Holzbearbeitungsmaschinen - Sicherheit - Teil 2: Horizontale Plattenkrei

3、ssgemaschinen mit Druckbalken (ISO 19085-2:2017) This European Standard was approved by CEN on 11 September 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any a

4、lteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language

5、made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Es

6、tonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTE

7、E FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 19085-2:2017 ENational fo

8、rewordThis British Standard is the UK implementation of EN ISO 19085-2:2017. It is identical to ISO 19085-2:2017.The UK participation in its preparation was entrusted to Technical Committee MTE/23, Woodworking machines.A list of organizations represented on this committee can be obtained on request

9、to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 85000 4ICS 13.110; 79.120.10Compliance with a Brit

10、ish Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 November 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN ISO 190852:2017EUROPEAN STANDARD

11、 NORME EUROPENNE EUROPISCHE NORM EN ISO 19085-2 August 2017 ICS 13.110; 79.120.10 English Version Woodworking machines - Safety - Part 2: Horizontal beam panel circular sawing machines (ISO 19085-2:2017) Machines bois - Scurit - Partie 2: Scies circulaires panneaux horizontales presseur (ISO 19085-2

12、:2017)Holzbearbeitungsmaschinen - Sicherheit - Teil 2: Horizontale Plattenkreissgemaschinen mit Druckbalken (ISO 19085-2:2017) This European Standard was approved by CEN on 11 September 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for

13、 giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three

14、 official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodi

15、es of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slov

16、enia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved

17、 worldwide for CEN national Members. Ref. No. EN ISO 19085-2:2017 EBS EN ISO 190852:2017EN ISO 19085-2:2017 (E) 3 European foreword This document (EN ISO 19085-2:2017) has been prepared by Technical Committee ISO/TC 39 “Machine tools” in collaboration with Technical Committee CEN/TC 142 “Woodworking

18、 machines - Safety” the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2018, and conflicting national standards shall be withdrawn at the latest by F

19、ebruary 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission

20、 and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN-CENELEC Internal Regulations, the national standards organizations of th

21、e following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherl

22、ands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 19085-2:2017 has been approved by CEN as EN ISO 19085-2:2017 without any modification. BS EN ISO 190852:2017EN ISO 19085-2:2017 (E) 4 Ann

23、ex ZA (informative) Relationship between this European Standard and the essential requirements of EU Directive 2006/42/EC This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association to provide one means of conforming to Ess

24、ential Requirements of the New Approach Machinery Directive 2006/42/EC. Once this standard is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of this standard confers, within the limits of the scope of this standard, a presumption of co

25、nformity with the relevant Essential Requirements, of that Directive and associated EFTA regulations. Table ZA.1 Correspondence between this European Standard and Directive 2006/42/EC Clauses and subclauses of this EN Essential Requirements (ERs) of Directive 2006/42/EC 1.1.2 Principles of safety in

26、tegration a) fitted for its function 5.1, 5.2, 5.3, 5.4, 5.5, 5.6, 5.7, 5.8, 6.5, 6.6, 7.12, 8.3 b) eliminate or reduce the risks, give measures, inform Clauses 5, 6, 7, 8 c) intended use and reasonably foreseeable misuse Clauses 5, 6, 7, 8 d) constraints in use 7.5, 8.3 e) equipment 6.1, 7.8, 8.3 1

27、.1.3 Materials and products 6.2, 6.5, 6.6, 7.3 1.1.4 Lighting 8.3 1.1.5 Design of machinery to facilitate its handling 5.2, 6.6, 7.5 1.1.6 Ergonomics 7.5 1.1.7 Operating position 5.2, 6.6.4, 6.6.8, 8.3 1.2.1 Safety and reliability of control systems 5.1, 5.6, 5.7, 5.9, 7.11, 7.12 1.2.2 Control devic

28、es 5.2, 5.3, 5.4, 5.5, 5.6, 6.6, 8.3 1.2.3 Starting 5.2, 5.3, 5.6 1.2.4 Stopping 5.2, 5.4, 5.5, 5.6 1.2.4.1 Normal stop 5.4 1.2.4.2 Operational stop 5.6 1.2.4.3 Emergency stop 5.5 BS EN ISO 190852:2017EN ISO 19085-2:2017 (E) 5 1.2.4.4 Assembly of machinery 6.6.8 1.2.5 Selection of control or operati

29、ng mode 5.3.2, 5.6 1.2.6 Failure of the power supply 5.8, 7.6, 7.11, 7.12 1.3 Protection against mechanical hazards 5.3, 5.4, 5.5, 5.6, 5.7, 5.8, 6.1, 6.2, 6.3, 6.4, 6.5, 6.6, 6.7, 8.1, 8.2, 8.3 1.3.1 Risk of loss of stability 6.1, 8.3 1.3.2 Risk of break-up during operation 6.2, 8.3 1.3.3 Risks due

30、 to falling or ejected objects 6.2, 6.3, 6.5 1.3.4 Risk due to surfaces, edges or angles 5.1 1.3.6 Risks relating to variations in the operating conditions 5.7, 6.5, 6.6 1.3.7 Risks related to moving parts 5.6, 6.6 1.3.8 Choice of protection against risks related to moving parts 6.6, 6.7 1.3.8.1 Mov

31、ing transmission parts 6.7 1.3.8.2 Moving parts involved in the process 6.5, 6.6 1.3.9 Risk of uncontrolled movements 5.3.2, 5.6, 6.5, 6.6 1.4.1 Required characteristics of guards and protective devices - General requirements 5.1, 6.2, 6.5, 6.6, 6.7 1.4.2.1 Fixed guards 6.6.1 1.4.2.2 Interlocking mo

32、vable guards 6.6.2 1.4.2.3 Adjustable guards restricting access 6.6 1.4.3 Special requirements for protective devices 5.1, 6.6 1.5.1 Electricity supply 5.9, 7.4, 7.11 1.5.2 Static electricity 7.8 1.5.3 Energy supply other than electricity 5.8, 7.6 1.5.4 Errors of fitting 7.9 1.5.6 Fire 7.1 1.5.8 Noi

33、se 7.2 1.5.11 External radiation 7.7 1.5.12 Laser equipment 7.9 1.5.13 Emission of hazardous materials and substances 7.3 1.6.1 Machinery maintenance 7.12 1.6.2 Access to operating position and servicing points 5.2, 6.6, 7.12 1.6.3 Isolation of energy sources 7.11 1.6.4 Operator intervention 5.2, 5.

34、6, 5.7, 6.6, 7.5, 7.12, 8.3 BS EN ISO 190852:2017EN ISO 19085-2:2017 (E) 6 1.6.5 Cleaning of internal parts 7.3, 8.3 1.7.1 Information and warnings on the machinery 8.1, 8.2 1.7.2 Warning devices 8.1 1.7.3 Marking of machinery 8.2 1.7.4 Instructions 8.3 2.3 Machinery for working wood and analogous m

35、aterials a) guiding 6.5 b) ejection 6.2, 6.9 c) brake 6.4 d) accidental tool contact 5.3.2, 5.4, 5.5, 5.6, 6.5, 6.6 WARNING Other requirements and other EU Directives may be applicable to the product(s) falling within the scope of this standard. BS EN ISO 190852:2017This page deliberately left blank

36、 ISO 19085-2:2017(E)Foreword vIntroduction vi1 Scope . 12 Normative references 23 Terms and definitions . 24 List of significant hazards . 75 Safety requirements and measures for controls . 95.1 Safety and reliability of control systems . 95.2 Control devices . 95.3 Start . 105.3.1 General. 105.3.2

37、Operating conditions .115.4 Safe stops 115.4.1 General. 115.4.2 Normal stop . 125.4.3 Operational stop 125.4.4 Emergency stop .125.5 Braking function of tool spindles . 125.6 Mode selection . 125.7 Spindle speed changing 125.7.1 Spindle speed changing by changing belts on the pulleys 125.7.2 Spindle

38、 speed changing by incremental speed change motor 125.7.3 Infinitely variable speed by frequency inverter .125.8 Failure of any power supply . 125.9 Manual reset control . 135.10 Enabling control 135.11 Machine moving parts speed monitoring . 135.12 Time delay 136 Safety requirements and measures fo

39、r protection against mechanical hazards .136.1 Stability . 136.1.1 Stationary machines 136.1.2 Displaceable machines 136.2 Risk of break-up during operation 136.3 Tool holder and tool design. 136.3.1 General. 136.3.2 Spindle locking .136.3.3 Circular saw blade fixing device 146.3.4 Flange dimension

40、for circular saw blades 146.4 Braking 146.4.1 Braking of tool spindles 146.4.2 Maximum run-down time . 146.4.3 Brake release 146.5 Safeguards 146.5.1 Fixed guards 146.5.2 Interlocking movable guards 146.5.3 Hold-to-run control 146.5.4 Two-hand control .146.5.5 Electro-sensitive protective equipment

41、(ESPE) .146.5.6 Pressure-sensitive protective equipment (PSPE).156.6 Prevention of access to moving parts . 156.6.1 General. 156.6.2 Guarding of tools .15 ISO 2017 All rights reserved iiiContents PageISO 19085-2:2017(E)Foreword vIntroduction vi1 Scope . 12 Normative references 23 Terms and definitio

42、ns . 24 List of significant hazards . 75 Safety requirements and measures for controls . 95.1 Safety and reliability of control systems . 95.2 Control devices . 95.3 Start . 105.3.1 General. 105.3.2 Operating conditions .115.4 Safe stops 115.4.1 General. 115.4.2 Normal stop . 125.4.3 Operational sto

43、p 125.4.4 Emergency stop .125.5 Braking function of tool spindles . 125.6 Mode selection . 125.7 Spindle speed changing 125.7.1 Spindle speed changing by changing belts on the pulleys 125.7.2 Spindle speed changing by incremental speed change motor 125.7.3 Infinitely variable speed by frequency inve

44、rter .125.8 Failure of any power supply . 125.9 Manual reset control . 135.10 Enabling control 135.11 Machine moving parts speed monitoring . 135.12 Time delay 136 Safety requirements and measures for protection against mechanical hazards .136.1 Stability . 136.1.1 Stationary machines 136.1.2 Displa

45、ceable machines 136.2 Risk of break-up during operation 136.3 Tool holder and tool design. 136.3.1 General. 136.3.2 Spindle locking .136.3.3 Circular saw blade fixing device 146.3.4 Flange dimension for circular saw blades 146.4 Braking 146.4.1 Braking of tool spindles 146.4.2 Maximum run-down time

46、. 146.4.3 Brake release 146.5 Safeguards 146.5.1 Fixed guards 146.5.2 Interlocking movable guards 146.5.3 Hold-to-run control 146.5.4 Two-hand control .146.5.5 Electro-sensitive protective equipment (ESPE) .146.5.6 Pressure-sensitive protective equipment (PSPE).156.6 Prevention of access to moving p

47、arts . 156.6.1 General. 156.6.2 Guarding of tools .15 ISO 2017 All rights reserved iiiContents PageBS EN ISO 190852:2017ISO 19085-2:2017(E)6.6.3 Guarding of drives .166.6.4 Guarding of shearing and/or crushing zones 176.7 Impact hazard . 246.8 Clamping devices . 256.9 Measures against ejection 256.9

48、.1 General. 256.9.2 Guards materials and characteristics256.10 Work-piece supports and guides 257 Safety requirements and measures for protection against other hazards .267.1 Fire 267.2 Noise . 267.2.1 Noise reduction at the design stage .267.2.2 Noise emission measurement . 267.3 Emission of chips

49、and dust 267.4 Electricity 267.4.1 General. 267.4.2 Displaceable machines 267.5 Ergonomics and handling . 277.6 Lighting . 277.7 Pneumatics 277.8 Hydraulics 277.9 Electromagnetic compatibility . 277.10 Laser 277.11 Static electricity . 277.12 Errors of fitting 277.13 Isolation . 277.14 Maintenance . 278 Information for use .278.1 Warning devices 278.2 Marking 278.2.1 General. 278.2.2 Additional markings 288.3 Instruction handbook 288.3.1 General. 288.3.2 Additional information 28Annex A (informative) Performance levels required .30Annex B