EN ISO 13088-2012 0625 Gas cylinders - Acetylene cylinder bundles - Filling conditions and filling inspection《气瓶 乙炔集束钢瓶 充装条件和充装检查》.pdf

《EN ISO 13088-2012 0625 Gas cylinders - Acetylene cylinder bundles - Filling conditions and filling inspection《气瓶 乙炔集束钢瓶 充装条件和充装检查》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 13088-2012 0625 Gas cylinders - Acetylene cylinder bundles - Filling conditions and filling inspection《气瓶 乙炔集束钢瓶 充装条件和充装检查》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationGas cylinders Acetylenecylinder bundles Fillingconditions and fillinginspectionBS EN ISO 13088:2012Copyright European Committee for Standardization Provided by IHS under license

2、with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 13088:2012National forewordThis British Standard is the UK implementation of EN ISO 13088:2012. It is identical to ISO 13088:2011. It supersedes BS ISO 13088:2011, which is withdrawn.The UK participa

3、tion in its preparation was entrusted by Technical Committee PVE/3, Gas containers, to Subcommittee PVE/3/7, Gas containers - Gas cylinder (receptacle) operations.A list of organizations represented on this subcommittee can be obtained on request to its secretary.This publication does not purport to

4、 include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013ISBN 978 0 580 77509 3 ICS 23.020.30 Compliance with a British Standard cannot confer immunity from legal obligations

5、.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2012.Amendments/corrigenda issued since publicationDate Text affected30 June 2013 This corrigendum renumbers BS ISO 13088:2011 as BS EN ISO 13088:2012BRITISH STANDARDCopyright Europe

6、an Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 13088 October 2012 ICS 23.020.30 English Version Gas cylinders - Acetylene cylinder bundl

7、es - Filling conditions and filling inspection (ISO 13088:2011) Bouteilles gaz - Cadres de bouteilles dactylne - Conditions de remplissage et contrle au remplissage (ISO 13088:2011) Gasflaschen - Acetylenflaschenbndel - Fllbedingungen und Inspektion beim Fllen (ISO 13088:2011) This European Standard

8、 was approved by CEN on 6 October 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such

9、 national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own

10、language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Gr

11、eece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUN

12、G Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 13088:2012: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo re

13、production or networking permitted without license from IHS-,-,-Foreword The text of ISO 13088:2011 has been prepared by Technical Committee ISO/TC 58 “Gas cylinders” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 13088:2012 by Technical Committee CEN/T

14、C 23 “Transportable gas cylinders” the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2013, and conflicting national standards shall be withdrawn at the

15、 latest by April 2013. This European Standard has been submitted for reference into the RID and/or in the technical annexes of the ADR. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsib

16、le for identifying any or all such patent rights. This document supersedes EN 12755:2000. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Cze

17、ch Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdo

18、m. Endorsement notice The text of ISO 13088:2011 has been approved by CEN as a EN ISO 13088:2012 without any modification. ii ISO 2013 All rights reservedBS EN ISO 13088:2012 ISO 13088:2012 (E)EN Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo

19、reproduction or networking permitted without license from IHS-,-,-iiiContents Page iv Introduction 1 Scope 1 2 Normative references 1 3 Terms and definitions . 1 4 Basic requirements for acetylene cylinder bundles 4 4.1 General . 4 4.2 Filling conditions . 4 5 Assembly, marking and documentation of

20、acetylene cylinder bundles . 5 5.1 Assembly 5 5.2 Verification of marking and necessary documentation 5 5.3 Documentation 6 6 Filling inspection for acetylene cylinder bundles 6 6.1 Pre-fill inspection 6 6.2 Solvent content 7 6.3 Number of consecutive fillings 8 6.4 Inspection during filling 8 6.5 P

21、ost-fill inspection 8 7 Individual filling of acetylene bundle cylinders . 9 Annex A (normative) Procedure for establishing the filling conditions of acetylene cylinder bundles . 10 Annex B (normative) Determination of the solvent content in the bundle in the course of the filling inspection 14 Bibl

22、iography 16 BS EN ISO 13088:2012 ISO 13088:2011 (E)Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-iv Introduction This International Standard aims at the harmonization of the di

23、fferent operating and filling conditions of acetylene cylinder bundles and covers requirements that reflect current practice and experience regarding inspection at the time of filling. Where there is any conflict between this International Standard and any applicable regulation, the regulation alway

24、s takes precedence. In International Standards, weight is equivalent to a force, expressed in newtons. However, in common parlance (as used in terms defined in this International Standard), the word “weight” continues to be used to mean “mass”, but this practice is deprecated (see ISO 80000-4). In t

25、his International Standard the unit bar is used, due to its universal use in the field of technical gases. It should, however, be noted that bar is not an SI unit, and that the according SI unit for pressure is pascal (Pa). Pressure values given in this International Standard are given as gauge pres

26、sure (pressure exceeding atmospheric pressure) unless noted otherwise. BS EN ISO 13088:2012 ISO 13088:2011 (E)Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-INTERNATIONAL STANDA

27、RD 1Gas cylinders Acetylene cylinder bundles Filling conditions and filling inspection 1 Scope This International Standard specifies the minimum requirements for the filling conditions and filling inspection of acetylene cylinder bundles. It applies both to bundles which are filled while the cylinde

28、rs are assembled in the bundle and to bundles of which the cylinders are filled as individual cylinders and are assembled into a bundle after filling. It does not apply to bundles containing solvent-free acetylene cylinders. This International Standard is not applicable to individual acetylene cylin

29、ders that are not intended to be assembled into a bundle (see ISO 11372). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenc

30、ed document (including any amendments) applies. ISO 11372, Gas cylinders Acetylene cylinders Filling conditions and filling inspection 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 acetylene cylinder cylinder manufactured and suitable for t

31、he transport of acetylene, containing a porous material and solvent for acetylene, with a valve and other accessories affixed to the cylinder NOTE When there is no risk of ambiguity, the word “cylinder” is used. 3.2 acetylene cylinder bundle transportable unit comprising of at least 2 cylinders up t

32、o and usually not exceeding 16 cylinders that are permanently connected together by a manifold and contained within a rigid frame equipped with all necessary equipment for filling and use 3.3 cylinder shell acetylene cylinders empty cylinder manufactured and suitable for receiving and containing a p

33、orous material for use as part of an acetylene cylinder 3.4 filler gas cylinders trained person responsible for inspection prior to, during and immediately after filling BS EN ISO 13088:2012 ISO 13088:201 (E)1Copyright European Committee for Standardization Provided by IHS under license with CENNot

34、for ResaleNo reproduction or networking permitted without license from IHS-,-,-2 3.5 maximum acetylene content acetylene cylinder bundles specified maximum weight of acetylene including saturation acetylene in the bundle cylinder NOTE For the relationship of the maximum acetylene content of bundle c

35、ylinders and of individual cylinders, see 4.2.1. 3.6 maximum acetylene charge acetylene cylinder bundles maximum acetylene content minus the saturation gas 3.7 porous material acetylene cylinders single- or multiple-component material introduced to, or formed in, the cylinder shell, that, due to its

36、 porosity, allows the absorption of a solvent/acetylene solution NOTE The porous material may be either: monolithic, consisting of a solid product obtained by reacting materials or by materials connected together with a binder, or non-monolithic, consisting of granular, fibrous or similar materials

37、without the addition of a binder. 3.8 residual gas acetylene cylinder bundles weight of acetylene including the saturation acetylene contained in the cylinders of a bundle returned for filling 3.9 saturation gas acetylene cylinders acetylene that remains dissolved in the solvent in the cylinder at a

38、tmospheric pressure (1,013 bar) and at a temperature of 15 C 3.10 solvent acetylene cylinders liquid that is absorbed by the porous material and is capable of dissolving and releasing acetylene NOTE The following abbreviations are used: “A” for acetone; “DMF” for dimethylformamide. 3.11 solvent oper

39、ating range acetylene cylinder bundles range from the minimum to the maximum solvent content permissible in a bundle which is filled while the cylinders are assembled NOTE For the determination of the solvent operating range, see Annex A. 3.12 specified solvent content acetylene cylinders weight of

40、solvent that the acetylene cylinder shall contain in accordance with the type approval BS EN ISO 13088:2012 ISO 13088:2011 (E)Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-33.1

41、3 tare acetylene cylinders reference weight of the acetylene cylinder including the specified solvent content NOTE 1 The tare is further specified in accordance with definitions 3.13.1 to 3.13.2. NOTE 2 For cylinders with solvent, the tare is expressed by indicating either tare S or both tare A and

42、tare S. 3.13.1 tare A acetylene cylinders sum of the weights of the empty cylinder shell, the porous material, the specified solvent content, the valve, the coating, where applicable, and all other parts that are permanently attached (e.g. by clamping or bolting) to the cylinder when it is presented

43、 to be filled 3.13.2 tare S acetylene cylinders tare A plus the weight of the saturation gas 3.14 bundle tare acetylene cylinder bundles reference weight of the acetylene cylinder bundle including its solvent NOTE The bundle tare is further specified in accordance with 3.14.1 to 3.14.4. 3.14.1 tare

44、BAmaxacetylene cylinder bundles sum of tare A for all cylinders permanently connected together by a manifold containing the maximum solvent content therefore including the amount of the positive solvent operating range (see A.3) plus the weights of the rigid frame and all other associated and perman

45、ently attached equipment 3.14.2 tare BSmaxacetylene cylinder bundles sum of tare S for all cylinders permanently connected together by a manifold containing the maximum solvent content including the amount of the positive solvent operating range (see A.3) plus the weights of the rigid frame and all

46、other associated and permanently attached equipment 3.14.3 tare BAminacetylene cylinder bundles sum of tare A of all cylinders permanently connected together by a manifold containing the minimum solvent content therefore excluding the amount of the negative solvent operating range (see A.3) plus the

47、 weights of the rigid frame and all other associated and permanently attached equipment 3.14.4 tare BSminacetylene cylinder bundles sum of tare S of all cylinders permanently connected together by a manifold containing the minimum solvent content therefore excluding the amount of the negative solven

48、t operating range (see A.3) plus the weights of the rigid frame and all other associated and permanently attached equipment 3.15 maximum gross weight acetylene cylinder bundles tare BAmaxplus the maximum acetylene content of all bundle cylinders or tare BSmaxplus the maximum acetylene charge of all bundle cylinders, respectively BS EN ISO 13088:2012 ISO 13088:2011 (E)Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4 3.16 w