EN ISO 4036-2012 en Hexagon thin nuts unchamfered (style 0) - Product grade B《六角薄螺母unchamfered乙级(0)风格产品》.pdf

《EN ISO 4036-2012 en Hexagon thin nuts unchamfered (style 0) - Product grade B《六角薄螺母unchamfered乙级(0)风格产品》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 4036-2012 en Hexagon thin nuts unchamfered (style 0) - Product grade B《六角薄螺母unchamfered乙级(0)风格产品》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 4036:2012Hexagon thin nuts unchamfered (style 0) Product grade BBS EN ISO 4036:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of E

2、N ISO 4036:2012. It supersedes BS EN ISO 4036:2001 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee FME/9, Fasteners.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to i

3、nclude all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013ISBN 978 0 580 78561 0 ICS 21.060.20 Compliance with a British Standard cannot confer immunity from legal obligations.T

4、his British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2013.Amendments issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 4036 December 2012 ICS 21.060.20 Supersedes EN ISO 4036:200

5、0English Version Hexagon thin nuts unchamfered (style 0) - Product grade B (ISO 4036:2012) crous bas hexagonaux sans chanfrein (style 0) - Grade B (ISO 4036:2012) Sechskantmuttern, niedrige Form (ohne Fase) - Produktklasse B (ISO 4036:2012) This European Standard was approved by CEN on 15 November 2

6、012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained

7、 on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CE

8、NELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, It

9、aly, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix

10、17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 4036:2012: EBS EN ISO 4036:2012EN ISO 4036:2012 (E) 3 Foreword This document (EN ISO 4036:2012) has been prepared by Technical Committee ISO/TC 2 “Fastene

11、rs“ incollaboration with Technical Committee CEN/TC 185 “Fasteners”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identicaltext or by endorsement, at the latest by June 2013, and conflicting national sta

12、ndards shall be withdrawn atthe latest by June 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patentrights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 40

13、36:2000. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, CzechRepublic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, Fran

14、ce, Germany, Greece,Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 4036:2012 has been approved by CEN as a EN ISO

15、4036:2012 without any modification. BS EN ISO 4036:2012ISO 4036:2012(E) ISO 2012 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope 12 Normative references . 13 Dimensions . 14 Requirements and reference International Standards 25 Designation . 2Bibliography . 3BS EN ISO 4036:2012I

16、SO 4036:2012(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject

17、 for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC)

18、on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees a

19、re circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held r

20、esponsible for identifying any or all such patent rights.ISO 4036 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 12, Fasteners with metric internal thread.This third edition cancels and replaces the second edition (ISO 4036:1999), of which it constitutes a minor revision.iv

21、 ISO 2012 All rights reservedBS EN ISO 4036:2012ISO 4036:2012(E)IntroductionThis International Standard belongs to a complete group of product standards developed by ISO on external hexagon drive fasteners. It comprises the following:a) hexagon head bolts (ISO 4014, ISO 4015, ISO 4016 and ISO 8765);

22、b) hexagon head screws (ISO 4017, ISO 4018 and ISO 8676);c) hexagon nuts (ISO 4032, ISO 4033, ISO 4034, ISO 4035, ISO 4036, ISO 7040, ISO 7041, ISO 7042, ISO 7719, ISO 7720, ISO 8673, ISO 8674, ISO 8675, ISO 10511, ISO 10512 and ISO 10513);d) hexagon bolts with flange (ISO 4162, ISO 15071 and ISO 15

23、072);e) hexagon nuts with flange (ISO 4161, ISO 7043, ISO 7044, ISO 10663, ISO 12125, ISO 12126 and ISO 21670). ISO 2012 All rights reserved vBS EN ISO 4036:2012BS EN ISO 4036:2012Hexagon thin nuts unchamfered (style 0) Product grade B1 ScopeThis International Standard specifies the characteristics

24、of unchamfered hexagon thin nuts (style 0), with threads from M1,6 up to and including M10 and product grade B.If, in special cases, specifications other than those listed in this International Standard are required, they can be selected from existing International Standards, for example ISO 724, IS

25、O 965-1 and ISO 4759-1.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable to its application. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 225, Fasteners

26、 Bolts, screws, studs and nuts Symbols and descriptions of dimensionsISO 724, ISO general-purpose metric screw threads Basic dimensionsISO 965-1, ISO general-purpose metric screw threads Tolerances Part 1: Principles and basic dataISO 3269, Fasteners Acceptance inspectionISO 4042, Fasteners Electrop

27、lated coatingsISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and CISO 6157-2, Fasteners Surface discontinuities Part 2: NutsISO 8839, Mechanical properties of fasteners Bolts, screws, studs and nuts made of non-ferrous metalsISO 8992, Fasteners General

28、 requirements for bolts, screws, studs and nutsISO 10683, Fasteners Non-electrolytically applied zinc flake coatings3 DimensionsSee Figure 1 and Table 1.Symbols and descriptions of dimensions are specified in ISO 225.Figure 1INTERNATIONAL STANDARD ISO 4036:2012(E) ISO 2012 All rights reserved 1BS EN

29、 ISO 4036:2012ISO 4036:2012(E)Table 1 DimensionsDimensions in millimetresThread DM1,6 M2 M2,5 M3 (M3,5)aM4 M5 M6 M8 M10Pb0,35 0,4 0,45 0,5 0,6 0,7 0,8 1 1,25 1,5e min. 3,28 4,18 5,31 5,88 6,44 7,50 8,63 10,89 14,20 17,59m max. 1,00 1,20 1,60 1,80 2,00 2,20 2,70 3,20 4,00 5,00min. 0,75 0,95 1,35 1,55

30、 1,75 1,95 2,45 2,90 3,70 4,70snom. = max. 3,20 4,00 5,00 5,50 6,00 7,00 8,00 10,00 13,00 16,00min. 2,90 3,70 4,70 5,20 5,70 6,64 7,64 9,64 12,57 15,57aIf possible, the size in parentheses should be avoided.bP is the pitch of the thread.4 Requirements and reference International StandardsSee Table 2

31、.Table 2 Requirements and reference International StandardsMaterial Steel (St) Non-ferrous metalGeneral requirementsInternational Standard ISO 8992ThreadTolerance class 6HInternational Standards ISO 724, ISO 965-1Mechanical propertiesHardness min. 110 HV30Materials as specified in ISO 8839Internatio

32、nal Standard ToleranceProduct grade BInternational Standard ISO 4759-1Finish CoatingAs processedRequirements for electroplating are specified in ISO 4042.Requirements for non-electrolytically applied zinc flake coatings are specified in ISO 10683.Additional requirements or other finishes or coatings

33、 shall be agreed between the supplier and the purchaser.Surface integrityLimits for surface discontinuities are specified in ISO 6157-2.Acceptability Acceptance inspection is specified in ISO 3269.5 DesignationEXAMPLE An unchamfered hexagon thin nut (style 0) with thread M6 made from steel (St) with

34、 a minimum hardness of 110 HV30 is designated as follows:Hexagon thin nut ISO 4036 - M6 - St2 ISO 2012 All rights reservedBS EN ISO 4036:2012ISO 4036:2012(E)Bibliography1 ISO 4014, Hexagon head bolts Product grades A and B2 ISO 4015, Hexagon head bolts Product grade B Reduced shank (shank diameter a

35、pproximately equal to pitch diameter)3 ISO 4016, Hexagon head bolts Product grade C4 ISO 4017, Hexagon head screws Product grades A and B5 ISO 4018, Hexagon head screws Product grade C6 ISO 4032, Hexagon regular nuts (style 1) Product grades A and B7 ISO 4033, Hexagon high nuts (style 2) Product gra

36、des A and B8 ISO 4034, Hexagon regular nuts (style 1) Product grade C9 ISO 4035, Hexagon thin nuts chamfered (style 0) Product grades A and B10 ISO 4161, Hexagon nuts with flange, style 2 Coarse thread11 ISO 4162, Hexagon flange bolts Small series Product grade combination A/B12 ISO 7040, Prevailing

37、 torque type hexagon regular nuts (with non-metallic insert) Property classes 5, 8 and 1013 ISO 7041, Prevailing torque type hexagon nuts (with non-metallic insert), style 2 Property classes 9 and 1214 ISO 7042, Prevailing torque type all-metal hexagon high nuts Property classes 5, 8, 10 and 1215 IS

38、O 7043, Prevailing torque type hexagon nuts with flange (with non-metallic insert), style 2 Product grades A and B16 ISO 7044, Prevailing torque type all-metal hexagon nuts with flange, style 2 Product grades A and B17 ISO 7719, Prevailing torque type all-metal hexagon regular nuts Property classes

39、5, 8 and 1018 ISO 7720, Prevailing torque type all-metal hexagon nuts, style 2 Property class 919 ISO 8673, Hexagon regular nuts (style 1) with metric fine pitch thread Product grades A and B20 ISO 8674, Hexagon high nuts (style 2) with metric fine pitch thread Product grades A and B21 ISO 8675, Hex

40、agon thin nuts chamfered (style 0) with metric fine pitch thread Product grades A and B22 ISO 8676, Hexagon head screws with metric fine pitch thread Product grades A and B23 ISO 8765, Hexagon head bolts with metric fine pitch thread Product grades A and B24 ISO 10511, Prevailing torque type hexagon

41、 thin nuts (with non-metallic insert)25 ISO 10512, Prevailing torque type hexagon regular nuts (with non-metallic insert) with metric fine pitch thread Property classes 6, 8 and 1026 ISO 10513, Prevailing torque type all-metal hexagon high nuts with metric fine pitch thread Property classes 8, 10 an

42、d 1227 ISO 10663, Hexagon nuts with flange, style 2 Fine pitch thread ISO 2012 All rights reserved 3BS EN ISO 4036:2012ISO 4036:2012(E)28 ISO 12125, Prevailing torque type hexagon nuts with flange (with non-metallic insert) with metric fine pitch thread, style 2 Product grades A and B29 ISO 12126, P

43、revailing torque type all-metal hexagon nuts with flange with metric fine pitch thread, style 2 Product grades A and B30 ISO 15071, Hexagon bolts with flange Small series Product grade A31 ISO 15072, Hexagon bolts with flange with metric fine pitch thread Small series Product grade A32 ISO 21670, He

44、xagon weld nuts with flange4 ISO 2012 All rights reservedBS EN ISO 4036:2012This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presen

45、ts the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4A

46、L UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and servi

47、ces. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8

48、996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response