EN ISO 4014-2011 en Hexagon head bolts - Product grades A and B《六角头螺栓 产品等级A和B级》.pdf

《EN ISO 4014-2011 en Hexagon head bolts - Product grades A and B《六角头螺栓 产品等级A和B级》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 4014-2011 en Hexagon head bolts - Product grades A and B《六角头螺栓 产品等级A和B级》.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 4014:2011Hexagon head bolts Productgrades A and B (ISO 4014:2011)BS EN ISO 4014:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of

2、EN ISO 4014:2011.It supersedes BS EN ISO 4014:2001 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee FME/9/3, Fasteners - Product Standards.A list of organizations represented on this committee can beobtained on request to its secretary.This publication d

3、oes not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 71149 7ICS 21.060.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority o

4、f theStandards Policy and Strategy Committee on 31 March 2011.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 4014 March 2011 ICS 21.060.10 Supersedes EN ISO 4014:2000English Version Hexagon head bolts - Product grades A and B (ISO 4014:2

5、011) Vis tte hexagonale partiellement filetes - Grades A et B (ISO 4014:2011) Sechskantschrauben mit Schaft - Produktklassen A und B (ISO 4014:2011) This European Standard was approved by CEN on 31 January 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulat

6、e the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Stan

7、dard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the nat

8、ional standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switze

9、rland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. E

10、N ISO 4014:2011: EBS EN ISO 4014:2011EN ISO 4014:2011 (E) 3 Foreword This document (EN ISO 4014:2011) has been prepared by Technical Committee ISO/TC 2 “Fasteners“ in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN. This European Standard shall b

11、e given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2011, and conflicting national standards shall be withdrawn at the latest by September 2011. Attention is drawn to the possibility that some of the elements of this doc

12、ument may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 4014:2000. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are

13、 bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spa

14、in, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 4014:2011 has been approved by CEN as a EN ISO 4014:2011 without any modification. BS EN ISO 4014:2011ISO 4014:2011(E) ISO 2011 All rights reserved iiiForeword ISO (the International Organization for Standardization)

15、is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be repres

16、ented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are

17、drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International

18、 Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 4014 was prepar

19、ed by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 10, Product standards for fasteners. This fourth edition cancels and replaces the third edition (ISO 4014:1999), of which it constitutes a minor revision. BS EN ISO 4014:2011ISO 4014:2011(E) iv ISO 2011 All rights reservedIntroduction Th

20、is International Standard belongs to a complete group of product standards developed by ISO on external hexagon drive fasteners. It comprises the following: a) hexagon head bolts (ISO 4014, ISO 4015, ISO 4016 and ISO 8765); b) hexagon head screws (ISO 4017, ISO 4018 and ISO 8676); c) hexagon nuts (I

21、SO 4032, ISO 4033, ISO 4034, ISO 4035, ISO 4036, ISO 7040, ISO 7041, ISO 7042, ISO 7719, ISO 7720, ISO 8673, ISO 8674, ISO 8675, ISO 10511, ISO 10512 and ISO 10513); d) hexagon bolts with flange (ISO 4162, ISO 15071 and ISO 15072); e) hexagon nuts with flange (ISO 4161, ISO 7043, ISO 7044, ISO 10663

22、, ISO 12125, ISO 12126 and ISO 21670). BS EN ISO 4014:2011INTERNATIONAL STANDARD ISO 4014:2011(E) ISO 2011 All rights reserved 1Hexagon head bolts Product grades A and B 1 Scope This International Standard specifies the characteristics of hexagon head bolts with threads from M1,6 up to and including

23、 M64, of product grade A for threads M1,6 to M24 and nominal lengths up to and including 10d or 150 mm, whichever is the shorter, and product grade B for threads over M24 or nominal lengths over 10d or 150 mm, whichever is the shorter. If, in special cases, specifications other than those listed in

24、this International Standard are required, they can be selected from existing International Standards, for example ISO 724, ISO 888, ISO 898-1, ISO 965-1, ISO 3506-1, ISO 4753 and ISO 4759-1. 2 Normative references The following referenced documents are indispensable for the application of this docum

25、ent. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 225, Fasteners Bolts, screws, st uds and nuts Symbols and descriptions of dimensions ISO 724, ISO general-purpose metric screw thre

26、ads Basic dimensions ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse thread and fine pitch thread ISO 965-1, ISO general-purpose metric screw threads Tolerances Part 1: Principles and basic data

27、 ISO 3269, Fasteners Acceptance inspection ISO 3506-1, Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs ISO 4017, Hexagon head screws Product grades A and B ISO 4042, Fasteners Electroplated coatings ISO 4753, Fasteners Ends of parts with externa

28、l ISO metric thread ISO 4759-1, Tolerances for fasteners Part 1: Bolts, sc rews, studs and nuts Product grades A, B and C ISO 6157-1, Fasteners Surface discontinuities Part 1: Bolts, screws and studs for general requirements ISO 8839, Mechanical properties of fasteners Bolts, screws, studs and nuts

29、made of non-ferrous metals ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts ISO 10683, Fasteners Non-electrolytical ly applied zinc flake coatings BS EN ISO 4014:2011ISO 4014:2011(E) 2 ISO 2011 All rights reserved3 Dimensions See Figure 1 and Tables 1 and 2. Symbols and des

30、criptions of dimensions are specified in ISO 225. Dimensions in millimetres a = 15 to 30. bPoint shall be chamfered or for threads u M4 may be as-rolled (sheared end) in accordance with ISO 4753. cIncomplete thread u u 2P. dReference datum for dw. eMaximum underhead fillet. Figure 1 BS EN ISO 4014:2

31、011ISO 4014:2011(E) ISO 2011 All rights reserved 3Table 1 Preferred threads Dimensions inmillimetresThread, dM1,6 M2 M2,5 M3 M4 M5 M6 M8 M10 Pa0,35 0,4 0,45 0,5 0,7 0,8 1 1,25 1,5 b 9 10 11 12 14 16 18 22 26 c 15 16 17 18 20 22 24 28 32 bref. d 28 29 30 31 33 35 37 41 45 max. 0,25 0,25 0,25 0,40 0,4

32、0 0,50 0,50 0,60 0,60 cmin. 0,10 0,10 0,10 0,15 0,15 0,15 0,15 0,15 0,15 damax. 2 2,6 3,1 3,6 4,7 5,7 6,8 9,2 11,2 nom. = max. 1,60 2,00 2,50 3,00 4,00 5,00 6,00 8,00 10,00 A 1,46 1,86 2,36 2,86 3,82 4,82 5,82 7,78 9,78 dsProduct grade B min. 1,35 1,75 2,25 2,75 3,70 4,70 5,70 7,64 9,64 A 2,27 3,07

33、4,07 4,57 5,88 6,88 8,88 11,63 14,63 dwProduct grade B min. 2,30 2,95 3,95 4,45 5,74 6,74 8,74 11,47 14,47 A 3,41 4,32 5,45 6,01 7,66 8,79 11,05 14,38 17,77 eProduct grade B min. 3,28 4,18 5,31 5,88 7,50 8,63 10,89 14,20 17,59 lfmax. 0,6 0,8 1 1 1,2 1,2 1,4 2 2 nom. 1,1 1,4 1,7 2 2,8 3,5 4 5,3 6,4 m

34、ax. 1,225 1,525 1,825 2,125 2,925 3,65 4,15 5,45 6,58 Product grade A min. 0,975 1,275 1,575 1,875 2,675 3,35 3,85 5,15 6,22 max. 1,3 1,6 1,9 2,2 3,0 3,74 4,24 5,54 6,69 kProduct grade B min. 0,9 1,2 1,5 1,8 2,6 3,26 3,76 5,06 6,11 A 0,68 0,89 1,10 1,31 1,87 2,35 2,70 3,61 4,35 kweProduct grade B mi

35、n. 0,63 0,84 1,05 1,26 1,82 2,28 2,63 3,54 4,28 rmin. 0,1 0,1 0,1 0,1 0,2 0,2 0,25 0,4 0,4 nom. = max. 3,20 4,00 5,00 5,50 7,00 8,00 10,00 13,00 16,00 A 3,02 3,82 4,82 5,32 6,78 7,78 9,78 12,73 15,73 sProduct grade B min. 2,90 3,70 4,70 5,20 6,64 7,64 9,64 12,57 15,57 BS EN ISO 4014:2011ISO 4014:201

36、1(E) 4 ISO 2011 All rights reservedTable 1 (continued)Dimensions inmillimetresThread, dM1,6 M2 M2,5 M3 M4 M5 M6 M8 M10 Product grade A B lsandlgfl lslglslglslglslglslglslglslglslglslgnom. min. max. min. max. min. max. min. max. min. max. min.max. min. max. min. max. min. max. min. max. min. max. 121

37、1,65 12,35 1,2 3 1615,65 16,35 5,2 7 4 6 2,75 5 For sizes above the solid, bold, stepped line, ISO 4017 is recommended. 2019,58 20,42 18,95 21,05 8 10 6,75 9 5,5 8 2524,58 25,42 23,95 26,05 11,7514 10,5 13 7,5 11 5 9 3029,58 30,42 28,95 31,05 15,5 18 12,5 16 10 14 7 12 3534,5 35,5 33,75 36,25 17,5 2

38、1 15 19 12 17 4039,5 40,5 38,75 41,25 22,5 26 20 24 17 22 11,7518 4544,5 45,5 43,75 46,25 25 29 22 27 16,7523 11,5 19 5049,5 50,5 48,75 51,25 30 34 27 32 21,7528 16,5 24 5554,4 55,6 53,5 56,5 32 37 26,7533 21,5 29 6059,4 60,6 58,5 61,5 37 42 31,7538 26,5 34 6564,4 65,6 63,5 66,5 36,7543 31,5 39 7069

39、,4 70,6 68,5 71,5 41,7548 36,5 44 8079,4 80,6 78,5 81,5 51,7558 46,5 54 9089,3 90,7 88,25 91,75 56,5 64 10099,3 100,7 98,25 101,75 66,5 74 110109,3 110,7 108,25 111,75 120119,3 120,7 118,25 121,75 BS EN ISO 4014:2011ISO 4014:2011(E) ISO 2011 All rights reserved 5Table 1 (continued)Dimensions inmilli

40、metresThread, dM12 M16 M20 M24 M30 M36 M42 M48 M56 M64 Pa1,75 2 2,5 3 3,5 4 4,5 5 5,5 6 b 30 38 46 54 66 c 36 44 52 60 72 84 96 108 bref. d 49 57 65 73 85 97 109 121 137 153 max. 0,60 0,8 0,8 0,8 0,8 0,8 1,0 1,0 1,0 1,0 cmin. 0,15 0,2 0,2 0,2 0,2 0,2 0,3 0,3 0,3 0,3 damax. 13,7 17,7 22,4 26,4 33,4 3

41、9,4 45,6 52,6 63 71 nom. = max. 12,00 16,00 20,00 24,00 30,00 36,00 42,00 48,00 56,00 64,00 A 11,73 15,73 19,67 23,67 dsProduct grade B min. 11,57 15,57 19,48 23,48 29,48 35,38 41,38 47,38 55,26 63,26 A 16,63 22,49 28,19 33,61 dwProduct grade B min. 16,47 22 27,7 33,25 42,75 51,11 59,95 69,45 78,66

42、88,16 A 20,03 26,75 33,53 39,98 eProduct grade B min. 19,85 26,17 32,95 39,55 50,85 60,79 71,3 82,6 93,56 104,86 lfmax. 3 3 4 4 6 6 8 10 12 13 nom. 7,5 10 12,5 15 18,7 22,5 26 30 35 40 max. 7,68 10,18 12,715 15,215 Product grade A min. 7,32 9,82 12,285 14,785 max. 7,79 10,29 12,85 15,35 19,12 22,92

43、26,42 30,42 35,5 40,5 kProduct grade B min. 7,21 9,71 12,15 14,65 18,28 22,08 25,58 29,58 34,5 39,5 A 5,12 6,87 8,6 10,35 kweProduct grade B min. 5,05 6,8 8,51 10,26 12,8 15,46 17,91 20,71 24,15 27,65 rmin. 0,6 0,6 0,8 0,8 1 1 1,2 1,6 2 2 nom. = max. 18,00 24,00 30,00 36,00 46 55,0 65,0 75,0 85,0 95

44、,0 A 17,73 23,67 29,67 35,38 sProduct grade B min. 17,57 23,16 29,16 35,00 45 53,8 63,1 73,1 82,8 92,8 BS EN ISO 4014:2011ISO 4014:2011(E) 6 ISO 2011 All rights reservedTable 1 (continued) Dimensions inmillimetresThread, dM12 M16 M20 M24 M30 M36 M42 M48 M56 M64 Product grade A B lsandlgfl lslglslgls

45、lglslglslglslglslglslglslglslgnom. min. max. min. max. min. max.min. max.min. max.min. max.min. max. min. max.min. max.min. max.min. max.min. max. 50 49,5 50,5 11,2520 55 54,4 55,6 53,5 56,5 16,2525 60 59,4 60,6 58,5 61,5 21,2530 65 64,4 65,6 63,5 66,5 26,2535 17 27 70 69,4 70,6 68,5 71,5 31,2540 22

46、 32 80 79,4 80,6 78,5 81,5 41,2550 32 42 21,5 34 90 89,3 90,7 88,25 91,75 51,2560 42 52 31,5 44 21 36 100 99,3 100,7 98,25 101,75 61,2570 52 62 41,5 54 31 46 110 109,3 110,7 108,25 111,75 71,2580 62 72 51,5 64 41 56 26,5 44 120 119,3 120,7 118,25 121,75 81,2590 72 82 61,5 74 51 66 36,5 54 130 129,2

47、130,8 128 132 76 86 65,5 78 55 70 40,5 58 140 139,2 140,8 138 142 86 96 75,5 88 65 80 50,5 68 36 56 150 149,2 150,8 148 152 96 106 85,5 98 75 90 60,5 78 46 66 160 158 162 106 116 95,5 108 85 100 70,5 88 56 76 41,5 64 180 178 182 115,5128 105 120 90,5 108 76 96 61,5 84 47 72 200 197,7 202,3 135,5148

48、125 140 110,5 128 96 116 81,5 104 67 92 220 217,7 222,3 132 147 117,5 135 103 123 88,5 111 74 99 55,5 83 240 237,7 242,3 152 167 137,5 155 123 143 108,5131 94 119 75,5 103 260 257,4 262,6 157,5 175 143 163 128,5151 114 139 95,5 123 77 107 280 277,4 282,6 177,5 195 163 183 148,5171 134 159 115,5143 9

49、7 127 300 297,4 302,6 197,5 215 183 203 168,5191 154 179 135,5163 117 147 320 317,15 322,85 203 223 188,5211 174 199 155,5183 137 167 340 337,15 342,85 233 243 208,5231 194 219 175,5203 157 187 BS EN ISO 4014:2011ISO 4014:2011(E) ISO 2011 All rights reserved 7Table 1 (continued) Dimensions inmillimetresThread, dM12 M16 M20 M24 M30 M36 M42 M48 M56 M64