EN ISO 3098-3-2000 en Technical Product Documentation - Lettering - Part 3 Greek Alphabet《技术产品文献 字体 第3部分 希腊字母 ISO 3098-3-2000》.pdf

《EN ISO 3098-3-2000 en Technical Product Documentation - Lettering - Part 3 Greek Alphabet《技术产品文献 字体 第3部分 希腊字母 ISO 3098-3-2000》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 3098-3-2000 en Technical Product Documentation - Lettering - Part 3 Greek Alphabet《技术产品文献 字体 第3部分 希腊字母 ISO 3098-3-2000》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、STDOBSI BS EN IS0 3098-3-ENGL 2000 W lb2LIbb9 OBB2b99 138 W BRITISH STANDARD Technical product documentation - Lettering - Part 3: Greek alphabet The European Standard EN IS0 30983:2000 has the status of a British Standard ICs 01.100.01; 01.110 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED B

2、Y COPYRIGET LAW BS EN IS0 3098-3:2000 Imqomting Corrigendum No. 1 STD-BSI BS EN IS0 3078-3-ENGL - present to the responsible inkdonavEuropean committee any enquiries on the interpretation, or proposals for change, and keep the UK interests hfOITn - monitor related internationai and European developm

3、ents and promuigate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normaily include an annex which lists nonnative references to international publica

4、tions with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index“, or by using the “Find” facility of the BSI S

5、tandards Electronic Catalogue. A British Standard does not purport to include ali the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of

6、 pages This document comprises a front cover, an inside front cover, the EN IS0 title page, the EN IS0 foreword page, the IS0 title page, pages ii and iii, a blank page, pages 1 to 5, the annex ZA page, an inside back cover and a back cover. The BSI copyright notice displayed in this document indica

7、tes when the document was last issued. This British Standard, having been prepared under the direction of the Consumer Products and Services Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 August 2000 Q BSI 11-2000 12054 November Incorpoa An

8、nex% Comgendum 12000 I No. 1 ISBN O 580 36263 1 EUROPEAN STANDARD EN IS0 309-3 NORME EUROPENNE EUROPISCHE NORM May 2000 ICs 01.1 00.01 English version Technical product documentation - Lettering - Part 3: Greek alphabet (IS0 3098-3:2000) Documentation technique de produits - Ecriture - Partie 3: Alp

9、habet grec (IS0 3098-3:2000) Technische Produktdokumentation - Schriften - Teil 3: Griechisches Alphabet (IS0 3098-3:2000) This European Standard was approved by CEN on 1 May 2000. CEN members are bound to comply with the CENEENELEC Internal Regulations which stipulate the conditions for giving this

10、 European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (En

11、glish, French, German). A version in any other language made by translation under the responsibiliy of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Rep

12、ublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITE EUROPEEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Central Secretariat: rue de Stas

13、sart, 36 8-1050 Brussels O 2000 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN IS0 3098-3:2000 E STD-BSI BS EN IS0 3078-3-ENGL 2000 m Lb24bb7 0882702 552 m EN IS0 3098-3:2000 Foreword The text of the International Standard IS0 309

14、8-3:2000 has been prepared by Technical Committee ISO/TC 1 O “Technical drawings, product definition and related documentation“ in collaboration with CEN/CMC. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the

15、 latest by November 2000, and conflicting national standards shall be withdrawn at the latest by November 2000. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Rep

16、ublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard IS0 3098-3:2000 was approved by CEN as a European Standard without any mo

17、dification. NOTE: Normative references to International Standards are listed in annex ZA (normative). STD.BSI BS EN IS0 3078-3-ENGL 2000 = Lb2Libb 0882701 497 EN IS0 3098-3:2000 I NTE R NAT I O N AL STANDARD IS0 3098-3 Second edition 2000-05-01 Technical product documentation - Lettering - Part 3: G

18、reek alphabet Documentation technique de produits - criture - Partie 3: Alphabet grec Reference number IS0 3098-3:2000(E) STD-BSI BS EN IS0 3098-3-ENGL 2000 Lb2LibbS 088270l 325 EN IS0 3098-3:2000 Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national

19、 standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Internationa

20、l organizations, governmental and non-governmental, in liaison with ISO, also take pari in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules

21、given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possib

22、ility that some of the elements of this part of IS0 3098 may be the subject of patent rights. IS0 shall not be held responsible for identifying any or all such patent rights. International Standard IS0 3098-3 was prepared by Technical Committee ISO/TC 1 O, Technical drawings, product definition and

23、related documentation, Subcommittee SC 1 , Basic conventions. This second edition of IS0 3098-3 cancels and replaces the first edition (IS0 3098-2:1984), which has been technically revised. IS0 3098 consists of the following paris, under the general title Technical product documentation - Lettering:

24、 - Part O: General requirements becomes Part 1 with the next revision - Part 2: Latin alphabet, numerals and marks - Part 3: Greek alphabet - Part 4: Diacritical and particular marks for the Latin alphabet - Part 5: CAD lettering of the Latin alphabet, numerals and marks - Part 6: Cyrillic alphabet

25、iii STD-BSI BS EN IS0 3098-3-ENGL 2000 m Lb2LibbS 0882705 2bl m EN IS0 3098-3:2000 Technical product documentation - Lettering - Part 3: Greek alphabet 1 Scope This part of IS0 3098 specifies use of the Greek alphabet as symbols in technical drawings and associated documents. It primarily concerns l

26、etters written with the aid of stencils, but is equally applicable to freehand lettering or other appropriate methods. 2 Normative reference The following normative document contains provisions which, through reference in this text, constitute provisions of this part of IS0 3098. For dated reference

27、s, subsequent amendments to, or revisions of, this publication do not apply. However, parties to agreements based on this part of IS0 3098 are encouraged to investigate the possibility of applying the most recent edition of the normative document indicated below. For undated references, the latest e

28、dition of the normative document referred to applies. Members of IS0 and IEC maintain registers of currently valid International Standards. IS0 3098-0:1997, Technical product documentation - Lettering - Part O: General requirements. 3 General requirements and dimensions For the general requirements

29、and the dimensions of characters, see IS0 3098-0. To obtain constant line density, avoid blotting at intersecting lines and facilitate writing, the characters shall be formed so that lines cross, or meet, at approximate right angles. 4 Examples The following examples are given as a guide to illustra

30、te the application of general requirements and dimensions for the Greek alphabet. 1 Lettering A, sloping alpha beta gamma delta epsilon zeta eta theta iota kappa lambda mu nu xi omicron pi rho sigma tau upsilon phi chi psi omega alpha beta gamma delta epsilon zeta eta theta iota kappa lambda mu nu x

31、i omicron pi rho sigma tau upsilon phi chi psi omega 2 STD.BS1 BS EN IS0 3078-3-ENGL 2000 Lb24bb7 O82707 03Li EN IS0 3098-3:2000 Lettering A, vertical alpha beta gamma delta epsilon zeta eta theta iota kappa lambda mu nu xi omicron pi rho sigma tau upsilon phi chi psi omega lambda mu nu xi omicron p

32、i rho sigma tau upsilon phi chi psi omega 3 STD.BSI BS EN IS0 3078-3-ENGL 2000 = Lb2qbbS 0882708 T70 = EN IS0 3098-3:2000 1 -ettering B, sloping alpha beta gamma delta epsilon zeta eta theta iota kappa lambda mu nu xi omicron pi rho sigma tau upsilon phi chi psi omega alpha beta gamma delta epsilon

33、zeta eta theta iota kappa lambda mu nu xi omicron pi rho sigma tau upsilon phi chi psi omega STD-BSI BS EN IS0 3098-3-ENGL 2000 W LbZLibbS 0882707 707 m EN IS0 3098-3:2000 Lettering B, vertical Preferred application alpha beta gamma delta epsilon zeta eta theta iota kappa IIIIIIIIIIIII II IIIlIIIIII

34、IIIII1IIIIIIIIIIIIIIIIIIIIIII II II IlII II IIIIIIIIIIlIIIIIIIlIIIIIIIIIIIIIlIIIIIII1III upsilon phi chi psi omega lambda mu nu xi omicron pi rho sigma tau upsilon phi chi psi omega 5 STD-BSI BS EN IS0 3078-3-ENGL 2000 LbZLibb7 0882710 b27 EN IS0 3098-3:2000 Annex ZA (normative) Normative references

35、 to international publications with their relevant European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For da

36、ted references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. Publication _Year Title - EN Year IS0 3098-0 199

37、7 Technical product documentation - Lettering - EN IS0 3098-0 1997 Part O: General requirements BS EN IS0 30983:2000 BSI STD.BS1 BS EN IS0 3098-3-ENGL ZOO0 D lb24bb9 O27lL 5b5 389 Chiswi-. High roa London w4 4AL BSI - British Standards Institution BSI is the independent donal body responsible for pr

38、eparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Stan- are updated by amendment or revision Users of British Standards should make sure that they possess the latest amendments or editions.

39、 It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone hding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technid committee responsible, the identity of which can be found on the inside Cont

40、 cover. Tel 020 8996 9OOO. Fz 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers autmnaically receive the latest editions of stan-. Buying standards rders for all BSI, intemational and foreign standards publications should be addressed to Cust

41、omer Services. Tel 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of informa

42、tion on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic infodon services are also available which give details on all its products and services. Contact the Information Centre. Tel: O20 8996 7111. Fax: 020 8996 70

43、48. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Am on Tel O20 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publica

44、tions. BSI also holds the copyright, in the UK, of the publications of the intemational standardizaton bodies. Except as permitted under the Copynght, Designs and Patents Act 1988 no extract may be reproduced, stored in a retried system or transmitted in any form or by any means - electronic, photoc

45、opying, recording or otherwise - without prior written permission hm BSL This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and aarice can be obtained hm the Copyright Manager. Tel: 020 8996 7070.