EN ISO 277-2010 en Binders for paints and varnishes - Raw tung oil - Requirements and methods of test《涂料和清漆用粘合剂 生桐油 试验方法和要求》.pdf

《EN ISO 277-2010 en Binders for paints and varnishes - Raw tung oil - Requirements and methods of test《涂料和清漆用粘合剂 生桐油 试验方法和要求》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 277-2010 en Binders for paints and varnishes - Raw tung oil - Requirements and methods of test《涂料和清漆用粘合剂 生桐油 试验方法和要求》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBinders for paints and varnishes Raw tung oil Requirements and methods of testICS 87.060.20g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g4

2、7g36g58BS EN ISO277:2010National forewordThis British Standard is the UK implementation of EN ISO 277:2010. It is identical to ISO 277:2002. It supersedes BS ISO 277:2002 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee STI/3, Paint media and related pr

3、oducts.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunit

4、y from legal obligations.BS EN ISO 277:2010This British Standard, having been prepared under the direction of the Materials and Chemicals Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 12 August 2002 BSI 2011Amendments/corrig

5、enda issued since publicationDate Comments 28 February 2011 This corrigendum renumbers BS ISO 277:2002 as BS EN ISO 277:2010ISBN 978 0 580 71427 6EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 277 November 2010 ICS 87.060.20 English Version Binders for paints and varnishes - Raw tung oil -

6、 Requirements and methods of test (ISO 277:2002) Liants pour peintures et vernis - Huiles de bois de Chine brutes - Exigences et mthodes dessai (ISO 277:2002) Bindemittel fr Beschichtungsstoffe - Rohes Holzl - Anforderungen und Prfverfahren (ISO 277:2002) This European Standard was approved by CEN o

7、n 16 October 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards m

8、ay be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the

9、CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta

10、, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploi

11、tation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 277:2010: E3 Foreword The text of ISO 277:2002 has been prepared by Technical Committee ISO/TC 35 “Paints and varnishes” of the International Organization for Standardization (ISO) and has been taken ove

12、r as EN ISO 277:2010 by Technical Committee CEN/TC 139 “Paints and varnishes” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2011, and conflicting nat

13、ional standards shall be withdrawn at the latest by May 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CEN

14、ELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuan

15、ia, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 277:2002 has been approved by CEN as a EN ISO 277:2010 without any modification. BS EN ISO 277:2010EN ISO 277:2010 (E)1Bind

16、ers for paints and varnishes Raw tung oil Requirements and methods of test 1 Scope This International Standard specifies the requirements and the corresponding methods of test for two types of raw tung oil suitable for paints and varnishes. It is not intended to apply to tung oils which are wholly o

17、r partly solidified as a result of polymerization. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these pu

18、blications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to

19、 applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 150:1980, Raw, refined and boiled linseed oil for paints and varnishes Specifications and methods of test ISO 654:1980, Short solid-stem thermometers for precision use ISO 2114:2000, Plastics (polyste

20、r resins) and paints and varnishes (binders) Determination of partial acid value and total acid value ISO 2811-1:1997, Paints and varnishes Determination of density Part 1: Pyknometer method ISO 3681:1996, Binders for paints and varnishes Determination of saponification value Titrimetric method ISO

21、4630:1997, Binders for paints and varnishes Estimation of colour of clear liquids by the Gardner colour scale ISO 5508:1990, Animal and vegetable fats and oils Analysis by gas chromatography of methyl esters of fatty acids ISO 5509:2000, Animal and vegetable fats and oils Preparation of methyl ester

22、s of fatty acids ISO 5661:1983, Petroleum products Hydrocarbon liquids Determination of refractive index ISO 10336:1997, Crude petroleum Determination of water Potentiometric Karl Fischer titration method ISO 15528:2000, Paints, varnishes and raw materials for paints and varnishes Sampling BS EN ISO

23、 277:2010EN ISO 277:2010 (E)2 3 Terms and definitions For the purposes of this International Standard, the following terms and definitions apply. 3.1 raw tung oil the product obtained directly by expression or extraction from the seeds of different species of the genus Aleurites (family Euphorbiacea

24、e) only 3.2 type F oil raw tung oil derived substantially from seeds of the species Aleurites fordii Hemsley 3.3 type M oil raw tung oil derived substantially from seeds of the species Aleurites montana Wilson 4 Requirements and test methods The two types of raw tung oil shall meet the requirements

25、given in Table 1. 5 Methods of test 5.1 General During the analyses, use only reagents of recognized analytical grade, and only distilled water or water of equivalent purity. 5.2 Sampling Take a representative sample of the oil to be tested, as described in ISO 15528. 5.3 Determination of gelation t

26、ime 5.3.1 Apparatus Ordinary laboratory apparatus and glassware, together with the following: 5.3.1.1 Glass test-tubes, 150 mm long and 16 mm nominal diameter, of wall thickness not greater than 1 mm. Each tube shall have a cork, having a hole through which a glass rod of diameter 3 mm to 4 mm can m

27、ove freely. 5.3.1.2 Electric heating block. 5.3.1.3 Thermometer, STC/0,5/245/305 complying with the requirements of ISO 654. 5.3.1.4 Stop-clock. 5.3.1.5 Glass rods, of diameter 3 mm to 4 mm. BS EN ISO 277:2010EN ISO 277:2010 (E)3Table 1 Required characteristics and test methods for raw tung oil Requ

28、irement Characteristic Type F tung oil Type M tung oil Test method at 20 C g/ml 0,935 to 0,940 0,930 to 0,940 Density at 23 Cag/ml 0,933 to 0,938 0,928 to 0,938 ISO 2811-1 at 20 C 1,517 to 1,521 1,510 to 1,518 Refractive index at 23 Cb1,516 to 1,521 1,509 to 1,517 ISO 5661 Colour (Gardner) max. 8cma

29、x. 8cISO 4630 Acid numberdmg KOH/g max. 5 max. 5 ISO 2114 Saponification number mg KOH/g 189 to 195 189 to 195 ISO 3661 Unsaponifiable-matter content % (by mass) max. 1 max. 1 ISO 150:1980, Annex Iodine number g iodine/100 g min. 205 e Gelation time minutes max. 15 max. 22 Subclause 5.3 Volatile-mat

30、ter (water) content % (by mass) max. 0,5 max. 0,5 ISO 10336 Insoluble-bromide content Negative result Negative result Subclause 5.4 Sediment and turbidity No insoluble sediment is allowed after 24 h storage; the raw tung oil shall be clear. No insoluble sediment is allowed after 24 h storage; the ra

31、w tung oil shall be clear. Fatty-acid composition % (by mass) of each fatty acid To be agreed between the interested partiesfTo be agreed between the interested partiesfISO 5508 and ISO 5509 aThe change in density per degree Celsius is 0,000 68. bThe change in refractive index per degree Celsius is

32、0,000 35.cThis corresponds to an iodine colour number of 20. dThe free-acid content, calculated as oleic acid, shall not exceed 2,5 % (by mass). eCalculate the iodine number from the number of double bonds as given by the fatty-acid composition. fTypical values of the contents of the fatty acids in

33、raw tung oil are given in Table 2.5.3.2 Preparation of sample Mix the sample of oil thoroughly by shaking. 5.3.3 Procedure Carry out the determination in duplicate. Pour 5 ml of the mixed sample into one of the test-tubes (5.3.1.1) and fit the test-tube with its cork and a glass rod (5.3.1.5). Place

34、 the test-tube in the heating block (5.3.1.2), heated to a temperature of 275 C to 277 C. Support the test-tube so that its bottom is approximately 15 mm above the base of the heating block. Similarly, support the thermometer (5.3.1.3) with the bottom of its bulb approximately 15 mm above the base o

35、f the heating block, adjacent to the test-tube. BS EN ISO 277:2010EN ISO 277:2010 (E)4 Start the stop-clock (5.3.1.4) and, when the test portion has been in the heating block for 12 min, raise the glass rod approximately 10 mm at intervals of 15 s. Record the time when the test sample has gelled, as

36、 shown by the test-tube rising with the rod. If the results of the two determinations differ by more than 30 s, repeat the test on another two 5 ml test samples of the oil. 5.4 Insoluble-bromide test 5.4.1 Reagents 5.4.1.1 Diethyl ether. 5.4.1.2 Bromine. 5.4.2 Preparation of sample Mix the sample of

37、 oil thoroughly by shaking. 5.4.3 Procedure Dissolve 1 ml of the mixed sample in 20 ml of diethyl ether (5.4.1.1) in a test-tube or a small flask, mix the solution well and place the test-tube or small flask in cold water. Add bromine (5.4.1.2) from a fine pipette, drop by drop, avoiding vigorous sh

38、aking, until a considerable excess is present, as indicated by a persistent strong red colour. Shake the test-tube or flask well, allow to stand in cold water for 15 min and examine the solution. If the solution is clear, this indicates that no insoluble bromide has been formed. 6 Typical values of

39、fatty-acid contents Table 2 gives typical values of the fatty-acid contents of raw tung oil, determined by gas-chromatographic analysis as described in ISO 5508 and ISO 5509. Table 2 Typical values of fatty-acid contents of raw tung oil Content Fatty acid % (by mass) Palmitic acid C16:0 Stearic acid

40、 C18:0 Oleic acid C18:1 Linoleic acid C18:2 Linolenic acid C18:3 -Eleostearic acid C18:3 -Eleostearic acid C18:3 Others (not identified) 2 to 3 1,5 to 2,5 4,5 to 8 6 to 9 0,1 to 0,3 64 to 80 4 to 15 0,3 to 1 BS EN ISO 277:2010EN ISO 277:2010 (E)57 Test report The test report shall contain at least t

41、he following information: a) a reference to this International Standard (ISO 277); b) all details necessary for complete identification of the product tested (manufacturer, trade name, batch number, etc.); c) the results of the tests, and whether or not the product complies with the relevant specifi

42、cation limits; d) any deviation, by agreement or otherwise, from the test methods specified; e) any specific agreements between the interested parties; f) the dates of the tests. BS EN ISO 277:2010EN ISO 277:2010 (E)BSI GroupHeadquarters 389 Chiswick High Road, London, W4 4AL, UK Tel +44 (0)20 8996

43、9001 Fax +44 (0)20 8996 7001 standardsBSI - British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards ar

44、e updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this Br

45、itish Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automaticall

46、y receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop o

47、n the Website http:/ response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and interna

48、tional standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing membe

49、rs of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British Standards Online can be found at http:/ information about BSI is availab