EN 61300-3-19-1997 en Fibre Optic Interconnecting Devices and Passive Components Basic Test and Measurement Procedures Part 3-19 Examinations and Measurements - Polarization Depend.pdf

《EN 61300-3-19-1997 en Fibre Optic Interconnecting Devices and Passive Components Basic Test and Measurement Procedures Part 3-19 Examinations and Measurements - Polarization Depend.pdf》由会员分享，可在线阅读，更多相关《EN 61300-3-19-1997 en Fibre Optic Interconnecting Devices and Passive Components Basic Test and Measurement Procedures Part 3-19 Examinations and Measurements - Polarization Depend.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD Fibre optic interconnecting devices and passive components - Basic test and measurement procedures Part 3. Examinations and measurements Section 19. Polarization dependence of return loss of a single-mode fibre optic component The European Standard EN 61300519 : 1997 has the status

2、of a British Standard ICs 33.180.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 1997 1997 31300-3-19 : EC 61300-3-19 : BS EN 613003-19 : 1997 This British Standard, having been prepared under the direction of the Electrotechnical Sector Board, was published under the

3、 authority of the Standards Board and comes into effect on 15 July 1997 O BSI 1997 ISBN O 680 27703 8 National foreword This British Stan- is the English language version of EN 6130W19 : 1997. It is identical with IEC 61300-3-19 : 1997. The UK participation in its preparation was entsusted by Techni

4、cal Committee EPLM, Fibre optics, to Subcommittee EPU6/2, Interconnecting devices and passive components, which has the responsibility to: - aid enquirers to understand the text, - present to the responsible internationalEuropean commit - the application of an index match material to the fibre end;

5、- attenuation in the fibre, for example with a mandrel wrap. 3.9 Data read-out/recording/processing devices This device provides a means to collect the transmitted power as the SOP is scanned, to perform the calculations, and to report the results at the end of the test. A computer-based system may

6、be used to fulfil this data acquisition and analysis function. 4 Procedure 4.1 Precautions 4:l.l of the requirements specified in 3.1 to 3.9 and in the detail specification. The apparatus and arrangement necessary to make these measurements shall meet all 4.1.2 Since the characteristics of the PA, B

7、D, DUT, and D are all functions of the wavelength of the source, the wavelength and other characteristics of the source are important and shall be ensured. STD-BSI BS EN b1300-3-L7-ENGL 1777 Lb24bb7 b25b87 780 Page 8 EN 61300-3-19 : 1997 4.1.3 The terminator is important for the measurement. Procedu

8、res to reduce the reflected power from the detectors and temporary joints to an acceptable level shall be used as described in 3.8. 4.1.4 Movement of any of the fibres or apparatus during the measurement may affect the state of polarization and lead to measurement error. Therefore, care should be ta

9、ken to ensure that no movement of the fibres or apparatus is allowed. 4.1.5 Cladding modes shall be stripped at the entry and exit ports of each element of the apparatus. If this is not accomplished by the fibre coating, cladding mode strippers are required. See also notes 1 and 2 of 4.3.9. 4.2 Meth

10、od A - All states of polarization 4.2.1 Measure the transfer coefficients T23 (from port 2 to part 3), 12, Ti4 of the branching device (refer to annex A of IEC 875-1) to make sure that the BD meets the requirements specified in 3.4 (see figure 3). The source for these measurements shall be the same

11、as that used in measuring the polarization dependence of the return loss of the DUT. IEC 274197 Figure 3 - 2 x 2 polarization independent branching device (BD) 4.2.2 Configure the measurement set-up as shown in figure 4 with the elements specified in 3.1 to 3.9. The structure of PA is shown in figur

12、e 1. The precautions described in 4.1 shall be followed in configurng the test set-up and in performing the measurements. Figure 4 - Measurement set-up 4.2.3 After ensuring the stability of the test Set-up, maximize the detected signal Pl, by rotating the linear polarizer. Fix the rotation angle of

13、the P plate. 4.2.4 Rotate the quarter-wave plate Q by 10“ or some other incremental angle specified in the detail specification through 180“ while measuring P2 versus 6 and 9, the angular orientations of Q and H respectively. 4.2.5 detail specification. Rotate the half-wave plate H by 10“ or some ot

14、her incremental angle specified in the 4.2.6 Repeat steps 4.2.4 and 4.2.5 until the half-wave plate has been rotated through 180“. 4.2.7 Read and record the detected values of P2 and Pl at the same values of and q. 4.2.8 Without adjusting or disturbing the test arrangement, cut the fibre at TJ3 and

15、remove the DUT from the test. 4.2.9 Insert the reference fibre as shown in figure 5. Read and record the detected power P2 for each value of 0 and cp. Figure 5 - Measurement set-up 4.2.10 The polarization dependence of return loss is calculated as follows: 4.3 Method B - Linear polarization only 4.3

16、.1 Repeat step 4.2.1. 4.3.2 Configure the measurement set-up as shown in figure 4 with the elements specified in 3.1 to 3.9. The structure of PA is shown in figure 2. The precautions described in 4.1 shall be followed in configuring the test set-up and in performing the measurements. All of the laun

17、ch fibre shall be deployed in a straight line configuration. The length of fibre between the launch and the DUT shall be less than 1/8 of a fibre beat length to ensure the linear polarization state is maintained at the DUT. If this is not known, the length shall be less than 3 m. 4.3.3 rotating the

18、linear polarizer. Fix the rotation angle of the P plate. After ensuring the stability of the test set-up, maximize the detected signal, Pl, by 4.3.4 The detected power, P2(cp), is recorded as the linear state of polarization is rotated through 180, where cp is the angular orientation of the state of

19、 polarization. The incremental angular adjustment shall be chosen to ensure that the required accuracy for the determination of the maximum and minimum transmitted power is achieved. 4.3.5 The input fibre shall not be disturbed for the duration of the measurement procedure to ensure that the state o

20、f polarization launched into the DUT is not altered. 4.3.6 Without adjusting or disturbing the test arrangement, cut the fibre at TJ3 and remove the DUT from the test. 4.3.7 Insert the reference fibre as shown in figure 5. Read and record the detected power P2() and Pl). 4.3.8 minimum values of the

21、ratio are each determined with P2 and P1 at the same values of ip. Record the maximum and minimum values of the ratio P2/P1. These maximum and Page 10 EN 61300-3-19 : 1997 4.3.9 The polarization dependence of return loss is calculated as follows: NOTES 1 power PD, that is launched into the DUT. The

22、formula is effective provided that the splitting ratio of ED T,2 is equal to i,., .e power P, equals the PD = (TldT12)Pl. 2 of the DUT. It is assumed that the return loss of the test Set-up is polarization independent and is much higher than that 5 Details to be specified The following details, as a

23、pplicable, shall be specified in the detail specification: - Source peak wavelength and spectral width - Method to be used - Description of polarization adjuster - Incremental adjustment angle of the half-wave plate - Description of polarization independent branching device used - Description of the

24、 reference fibre - Pigtail lengths - Performance requirements - Any deviations from the test procedure. Page 11 EN 61300-3-19 : 1997 Annex ZA (normative) Normative references to international publications with their corresponding European publications This European Standard incorporates by dated or

25、undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only w

26、hen incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). NOTE: When an international publication has been modified by common modifications, indicated by (mod), the relevant ENIHD applies. Publication - Y

27、ear Title EN/HD - Year IEC 875-1 1996 Fibre optic branching devices Part 1 : Generic specification BS EN 61300-3-19 : I 1997 IEC 61300-3-19 : I BSI - British Standards Institution BSI 389 Chiswick High Road London w4 4AL ;SI is the independent national body responsible for preparing British Standard

28、s. It Iresents the UK view on standards in Europe and at the international level. It is icorporated by Royal Charter. :ontract requirements L British Standard does not purport to include aii the necessary provisions of a oninct. Users of British Standards are responsible for their correct applicatio

29、n. levisions Iritish Standards are updated by amendment or revision. Users of British Standards hould make sure that they possess the latest amendments or editions. t is the constant aim of BSI to improve the quality of our products and services. We vouid be grateful if anyone finding an inaccuracy

30、or ambiguity while using this 3ritish Standard would inform the Secretary of the responsible technical committee, he identity of which can be found on the inside front cover. Tel: 0181 996 9000; Fax: 1181 996 7400. 3SI offers members an individd updating service called PLUS which ensures that mbscri

31、bers automatically receive the latest editions of standards. 3uying standards lrders for aii BSI, international and foreign standards publications should be iddressed to Customer Services, Sales Department at Chiswick Tel 0181 996 7000; ?ax: 0181 996 7001. h response to orders for international stan

32、dards, it is BSI policy to supply the BSI mplementation of those that have been published as British Standards, unless Ithenvise requested. nformation on standards BSI provides a wide range of information on national, European and international 3tandards through its Library, the Standardline Databas

33、e, the BSI Information rechnology Service (BITS) and its Technid Help to Exporters Service. Contact the information Department at Chiswick: Tel 0181 996 7111; Fax: 0181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purch

34、ase price of standards. For details of these and other benefits contact Customer Services, Membership at Chiswick Tel: 0181 996 7002; Fax 0181 996 7001. Copyright Copyright subsists in ali BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationai standardiza

35、ion bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not preclu

36、de the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager, BSI, 389 Chiswick High Road, London W4 4AL.