EN 60512-1-4-1997 en Electromechanical Components for Electronic Equipment - Basic Testing Procedures and Measuring Methods - Part 1 General - Section 4 Test 1d Contact Protection .pdf

《EN 60512-1-4-1997 en Electromechanical Components for Electronic Equipment - Basic Testing Procedures and Measuring Methods - Part 1 General - Section 4 Test 1d Contact Protection .pdf》由会员分享，可在线阅读，更多相关《EN 60512-1-4-1997 en Electromechanical Components for Electronic Equipment - Basic Testing Procedures and Measuring Methods - Part 1 General - Section 4 Test 1d Contact Protection .pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD Electromechanical components for electronic equipment Basic testing procedures and measuring methods Part 1 : General- Section 4: Test 1 d. Contact protection effectiveness (scoop-proof) The European Standard EN 60512-14:1997 has the status of a British Standard ICs 31.220.01 BS EN

2、60512-1-411997 IEC 60512-1-4: 1997 Incorporating Corrigendum No. I Wk -present to the responsible internationalEuropean committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; -monitor related international and European developments and promulgate

3、them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. From 1 January 1997, all IEC publications have the number 60000 added to the old number. For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period of time during the ch

4、ange over from one numbering system to the other, publications may contain identifiers from both systems. Cr oss-r e fer enc e s The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section ent

5、itled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compli

6、ance with a British Standard does not ofitself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 7 and a back cover. The BSI copyright notice displayed in this document indicates when t

7、he document was last issued. Amendments issued since publication ISBN O 580 28736 X BS EN 60512-1-411997 Contents National foreword Page Inside fiont cover Foreword Text ofEN 60512-1-4 2 3 i O BSI 12 February 2002 11 blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60512-1-4 October 1997 I

8、Cs 3 1.220.0 1 English version Electromechanical components for electronic equipment Basic testing procedures and measuring methods - Part 1 : General - Section 4: Test Id: Contact protection effectiveness (scoop-proof) (IEC 60512-1-411997) Compo sant s lectromcanique s pour quipements lectroniques

9、Procdures dessai de base et mthodes de mesure - Partie 1: Gnralits - Section 4: Essai Id: Efficacit de la protection Elektrisch-mechanische Bauelemente fr elektronische Einrichtungen Me- und Prfverfahren - Teil 1 : Allgemeines - Hauptabschnitt 4: Prfung Id: Wirksamkeit des Kontaltschutzes (Scoop-pro

10、of) des contacts (scoop-proof) (IEC 60512-1-411997) (CE1 60512-1-411997) This European Standard was approved by CENELEC on 1997-1 0-0 1. CENELEC members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status ofa nation

11、al standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in

12、any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France,

13、Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central

14、 Secretariat: rue de Stassart 35, B-1050 Brussels O 1997 CENELEC -Ail rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref No. EN 605 12-1-4: 1997 E EN 605 12-1-411997 Foreword The text of document 48B/598/FDIS, future edition 1 ofIEC 60512-1-4, prepared by

15、 SC 48B, Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60512-14 on 1997-10-01. The following dates were fixed: Contents - latest date by which the EN has to b

16、e implemented at national level by publication of an identical national standard or by - latest date by which the national standards conflicting with the EN endorsement (dq) 1998-07-0 1 have to be withdrawn (dw) 1998-07-01 Annexes designated “normative” are part of the body of the standard. In this

17、standard, Annex ZA is normative. Annex ZA has been added by CENELEC Endor sement notice The text of the International Standard IEC 605 12-1-4: 1997 was approved by CENELEC as a European Standard without any modification. Foreword 1 Scope and object 2 Normative reference 3 Preparation of specimens 4

18、Test methods 5 Requirements 6 Details to be specified Annex ZA (normat ive) Normative references to international publications with their corresponding European publications Inside back cover Figure 1 - Method A: Example Figure 2 -Method B: Free connector with male contacts coupled to fixed connecto

19、r with male contacts with cylindrical connector 4 5 Page 2 3 3 3 3 5 5 2 O BSI 12 February 2002 EN60512-14:1997 1 Scope and object This section of IEC 60512-1 is to be used when referenced by the detail specification to test mechanical components overseen by the IEC subcommittee 48B. This test can a

20、lso be done on similar devices when the detail specification so prescribes. The object ofthis test is to define a standard test methodto verify the ability ofa connector to prevent the accidental touching ofits contact by the front ofthe mating connector. It is primarily intended to be applied to cy

21、lindrical multi-contact connectors which are required to be scoop-proof 2 Normative reference The foliowing normative document contains provisions which, through reference in this text, constitute provisions of this section of IEC 605 12-1. At the time ofpublication, the edition indicated was valid.

22、 Ail normative documents are subject to revision, and parties to agreements based on this section of IEC 605 12-1 are encouraged to investigate the possibility of applying the most recent edition of the normative document indicated below. Members of IEC and IS0 maintain registers of currently valid

23、Intern at ional Standards . IEC 605 12-21 1985, Electromechanical components for electronic equipment -Basic testingprocedures and measuring methads -Part 2: General examination, electrical continuity and contact resistance tests, insulation tests and voltage stress tests 3 Preparation of specimens

24、The connectors shall be fitted with their full set ofcontacts. They shall be wired as specified by the detail specification. 4 Test methods 4.1 Procedure A suitable device for detecting electrical continuity, such as an ohmmeter, shall be connected between the housing (shell) of the free connector a

25、nd all of the contacts in the fixed connector wired together. O BSI 12 February 2002 3 EN 60512-1-411997 4.2 Method A While attempting to mismate the free connector, fitted with female contacts to the fixed connector fitted with male contacts, at various angles and rotations as illustrated in Figure

26、 1, any evidence of electrical continuity shall be noted. The test is then repeated on a set ofconnectors with the free connector fitted with male contacts and the fixed connector fitted with female contacts. T Figure 1 -Method A: Example with cylindrical connector 4 OBSI 12 February 2002 EN60512-14

27、:1997 4.3 Method B The free connector fitted with male contacts is coupled with the fixed connector fitted also with male contacts (see Figure 2). The connectors shall be subjected to the test 4a, voltage proof test, in accordance with IEC 60512-2 60512-4-111) at the specified test voltage. The volt

28、age shall be applied between each group ofcontacts, one group consisting ofall contacts in the free connector connected together, the second with all the contacts in the fixed connector connected together. 1 l I l Figure 2 - Method B: Free connector with male contacts coupled to fixed connector with

29、 male contacts 5 Requirements 5.1 Method A During the attempted mismating, there shall be no evidence of electrical continuity between the housing (metal shell) and the male contacts. 5.2 Method B No breakdown or flashover shall be observed. 6 Details to be specified When this test is required by th

30、e detail specification, the following details shall be specified: a) preparation of the specimen including details ofthe wiring; b) test voltage for method B; c) any deviation from the standard test method. 1) Publication number of the future edition 5 O BSI 12 February 2002 6 blank EN60512-14:1997

31、Annex ZA (normative) Normative references to international publications with their corresponding European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and

32、 the publications are listed hereafter. For dated references, subsequent amendments to or revisions ofany ofthese publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (incl

33、uding amendments). NOTE applies. When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD Publication Year Title EN/HD Year IEC 60512-2 1985 Electromechanical components for electronic - - equipment - Basic testing procedures and measuring m

34、ethods -Part 2: General examination, electrical continuity and contact resistance tests, insulation tests and voltage stress tests O BSI 12 February 2002 I BS EN IEC 605 12- 1-41 1997 605 12- 1-41 1997 BSI 389 Chiswick High Road Lon don w4 4AL BSI is the independent national body responsible for pre

35、paring British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Re vi si ons British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or ed

36、itions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the

37、inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards public

38、ations should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: orders&-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those tha

39、t have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are

40、 also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 71 11. Fax: +44 (0)20 8996 7048. Email: infomi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price

41、 of standards. For details ofthese and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 700 1. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further informatio

42、n about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, ofthe publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extra

43、ct may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise -without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, ofnecessary details such as sy

44、mbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then the prior written permission ofBSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyright&-.