ASD-STAN PREN 4165-013-2003 Aerospace series Connectors electrical rectangular modular Operating temperature 175 Degrees C continuous Part 013 Cable clamp 2 and 4 modules for conne.pdf

《ASD-STAN PREN 4165-013-2003 Aerospace series Connectors electrical rectangular modular Operating temperature 175 Degrees C continuous Part 013 Cable clamp 2 and 4 modules for conne.pdf》由会员分享，可在线阅读，更多相关《ASD-STAN PREN 4165-013-2003 Aerospace series Connectors electrical rectangular modular Operating temperature 175 Degrees C continuous Part 013 Cable clamp 2 and 4 modules for conne.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM prEN 4165-013 Edition P 2 October 2013 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Rue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.org ICS: 49.060 Supersedes edition

2、P 1 of February 2003 and will supersede EN 4165-013:2005 Descriptors: ENGLISH VERSION Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuous Part 013: Cable clamp 2 and 4 modules for connectors, series 2 and series 3 Product standard Srie arospatiale Con

3、necteurs lectriques rectangulaires modulaires Temprature dutilisation 175 C continu Partie 013 : Serre-cbles 2 et 4 modules pour connecteurs, srie 2 et srie 3 Norme de produit Luft- und Raumfahrt Elektrischer Rechtecksteckverbinder in modularer Bauweise Betriebstemperatur 175 C konstant Teil 013: En

4、dgehuse mit Zugentlastungsklemme fr freien Steckverbinder, 2 und 4 Modulen, Serie 2 und Serie 3 Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for t

5、he needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically o

6、r functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN

7、). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 1 October 2013 Comments should be sent within six months after the date o

8、f publication to ASD-STAN Electrical Domain Copyright 2013 by ASD-STAN prEN 4165-013:2013 (E) 2 Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Terms and definitions .3 4 Required characteristics .3 5 Cable clamp 4 5.1 For 2 modules classes W and F .4 5.2 For 4 modules classes W and F

9、.4 5.3 For 2 modules class C .5 5.4 For 4 modules class C .5 5.5 Cable clamp class 6 5.6 Intermateability for series 2 and series 3 6 6 Designation 7 7 Marking .7 8 Technical specification .7 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. Afte

10、r inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 4165-013:2013 (E) 3 1 Scope This standard defines cable clamp for 2 and 4 module connectors, series 2 and series 3 used in

11、 the family of rectangular electrical connectors. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest editi

12、on of the referenced document (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace products EN 4165-001, Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuous Part 001: Technical specification EN 4165-002, Aerospace series

13、Connectors, electrical, rectangular, modular Operating temperature 175 C continuous Part 002: Specification of performance and contact arrangements 3 Terms and definitions For the purposes of this standard, the terms and definitions given in EN 4165-001 apply. 4 Required characteristics See Figure 1

14、 and Figure 3 for 2 modules; Figure 2 and Figure 4 for 4 modules. prEN 4165-013:2013 (E) 4 5 Cable clamp 5.1 For 2 modules classes W and F See Figure 1. Dimensions are in millimetres. Key 1 see Figure 6 Figure 1 5.2 For 4 modules classes W and F See Figure 2. Dimensions are in millimetres. Key 1 See

15、 Figure 6 Figure 2 prEN 4165-013:2013 (E) 5 5.3 For 2 modules class C See Figure 3. Dimensions are in millimetres. Key 1 See Figure 6. Figure 3 5.4 For 4 modules class C See Figure 4. Dimensions are in millimetres. Key 1 See Figure 6 Figure 4 prEN 4165-013:2013 (E) 6 5.5 Cable clamp class See Table

16、1. Table 1 Class DescriptionW Cable clamp with housing (shell) olive drab cadmium plated, aluminium alloy, 500 hours resistance to salt mist, maximum operating temperature 175 C continuous F Cable clamp with housing (shell) black nickel plated, aluminium alloy, 96 hours resistance to salt mist, maxi

17、mum operating temperature 175 C continuous C Monobloc cable clamp. composite material, maximum operating temperature 175 C continuous 5.6 Intermateability for series 2 and series 3 See Figure 5. Dimensions are in millimetres. Key 1 4 modules 70,9 max. 2 modules 40,4 max. Figure 5 prEN 4165-013:2013

18、(E) 7 See Figure 6. Dimensions are in millimetres. Key 1 4 modules 70,9 max. 2 modules 40,4 max. Figure 6 6 Designation EXAMPLE Description block ELECTRICAL CONNECTOR CABLE CLAMP Identity block EN4165F13A4 Number of the basic standard Class type (see Table 1) Type 13: Cable clamp (see EN 4165-002) A series 2 or series 3 Shell type 4 plug 4 modules 2 plug 2 modules 7 Marking Unless there are other specific contractual requirements, the marking shall be in accordance with EN 2424, category P. 8 Technical specification See EN 4165-001.