EN 50289-3-5-2001 en Communication Cables - Specifications for Test Methods Part 3-5 Mechanical Test Methods - Crush Resistance of the Cable《通信电缆 试验方法规范 第3-5部分 机械试验方法 电缆的抗挤压性》.pdf

《EN 50289-3-5-2001 en Communication Cables - Specifications for Test Methods Part 3-5 Mechanical Test Methods - Crush Resistance of the Cable《通信电缆 试验方法规范 第3-5部分 机械试验方法 电缆的抗挤压性》.pdf》由会员分享，可在线阅读，更多相关《EN 50289-3-5-2001 en Communication Cables - Specifications for Test Methods Part 3-5 Mechanical Test Methods - Crush Resistance of the Cable《通信电缆 试验方法规范 第3-5部分 机械试验方法 电缆的抗挤压性》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD Communication cables - Specifications for test methods - Part 3-5: Mechanical test methods - Crush resistance of the cable The European Standard EN 50289-3-5:2001 has the status of a British Standard ICs 33.120.10 BS EN 50289-3-5:200 1 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PER

2、MITTED BY COPYRIGHT LAW - BS EN 50289-3-52001 Amd. No. National foreword Date Comments This British Standard is the official English language version of EN 50289-3-5:2001. The UK participation in its preparation was entrusted by Technical Committee EPL146, Cables, wire and waveguides, RF connectors,

3、 and accessories for communication and signalling, to Subcommittee EPL/46/1, Communication cables, which has the responsibility to: - - aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK in

4、terests informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publicatio

5、ns referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find facility of the BSI Standards Electronic Cat alo gue . A British Standard does not purport to include all the necessary provisi

6、ons of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. This British Standard, having been prepared under the direction of the Electrotechnical Sector Policy and Strateg

7、y Committee, was published under the authority of the Standards Policy and Strategy Committee on 13 November 2001 O BSI 13 November 2001 Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover. The BSI copy

8、right date displayed in this document indicates when the document was last issued. Amendments issued since publication ISBN O 580 38688 O EUROPEANSTANDARD EN 50289-3-5 NORME EUROPENNE EUROPISCHE NORM August 2001 ICs 33.120.10 English version Communication cables - Specifications for test methods Par

9、t 3-5: Mechanical test methods - Crush resistance of the cable Cbles de communication - Spcifications des mthodes dessai Partie 3-5: Mthodes dessais mcaniques - Rsistance lcrasement du cble Kommunikationskabel - Spezifikationen fr Prfverfahren Teil 3-5: Mechanische Prfverfahren - Querdruckbestndigke

10、it des Kabels This European Standard was approved by CENELEC on 2001-05-01. CENELEC members are bound to comply with the CENICENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bi

11、bliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibi

12、lity of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, L

13、uxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Centrai Secretariat: rue de Stassart 35, B - 1050

14、Brussels O 2001 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 50289-3-5:2001 E EN 50289-3-512001 -2- Foreword This European Stanc-rd was prepared by the Technical Committee CENELEC TC 46X, Communication cables. The text of the d

15、raft was submitted to the formal vote and was approved by CENELEC as EN 50289-3-5 on 2001 -05-01. The following dates were fixed: - latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2002-04-01 - latest date by

16、 which the national standards conflicting with the EN have to be withdrawn (dow) 2004-04-01 This European Standard has been prepared under the European Mandate M/212 given to CENELEC by the European Commission and the European Free Trade Association. -3- EN50289-3-5:2001 Contents 1 Scope 4 2 Normati

17、ve references 4 3 Definitions . 4 4 Test method . 4 4.1 Equipment . 4 4.2 Test sample . 4 4.3 Procedure 5 4.4 Requirements 5 4.4. I Coaxial cables . 5 4.4.2 Symmetrical cables . . 5 4.4.3 Optical cables . 6 5 Test report . 6 EN 50289-3-5:2001 -4- 1 Scope This Part 3-5 of EN 50289 details the method

18、of test to determine the crush resistance of the cable used in analogue and digital communication systems. It is to be read in conjunction with Part 3-1 of EN 50289, which contains essential provisions for its application. 2 Normative references This European Standard incorporates by dated or undate

19、d reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when in

20、corporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 50289-3-1 2001 Communication cables - Specifications for test methods - Part 3-1: Mechanical test methods - General requirements EN 50290-1- 2” Commu

21、nication cables - Part 1-2: Definitions 3 Definitions For the purposes of this European Standard the definitions of EN 50290-1-2 apply. 4 Test method 4.1 Equipment The apparatus shall allow a sample of cable to be crushed between a flat steel base plate and a movable steel plate which applies the cr

22、ushing force uniformly over a 100 mm length of the sample. The edges of the movable plate shall be rounded with a radius of about 5 mm. They are not included in the 100 mm flat part of this plate. A suitable apparatus is shown in Figure I. 4.2 Test sample The sample shall be of a length sufficient t

23、o carry out the test specified. For small cables (less than 5 mm outer diameter) the cables may be tested forming a loop (top of Figure 1) in this case the force to be applied is twice the specified force. The radius of the loop shall be large enough not to affect the transmission characteristics of

24、 the cable. ) At drafi stage. -5- EN50289-3-5:2001 4.3 Procedure The cable sample shall be mounted on the base plate of the test apparatus so that lateral movement is prevented. The cable specimen is compressed by a parallel flat movable steel plate with rounded edges applying a load (see Figure 1).

25、 The load (F) as indicated in the relevant cable specification shall be applied gradually without any abrupt change for a duration of 2 minutes. If incremental loading is used the steps shall not exceed a ratio of 1,5 :I If requested in the relevant specification, an additional or alternative test m

26、ay be performed by inserting one or more steel mandrels (25 mm in diameter unless otherwise specified in the detail specification) perpendicular to the sample, to represent particular operational conditions. 2F / Cable under test radius o I V 100 mm Figure 1 - Crushing test 4.4 Requ i remen ts 4.4.1

27、 Coaxial cables After the load has been removed the magnitude of the impedance irregularity introduced by the test shall be measured by a pulse or TDR method. After the test, the reflection characteristics shall be within the limiting values specified in the detail specification. 4.4.2 Symmetrical c

28、ables After the test, the transmission characteristics shall be within the limiting values specified in the relevant specification. EN 50289-3-512001 -6- 4.4.3 Optical cables After the test, the transmission characteristics shall be within the limiting values specified in the relevant specification.

29、 5 Test report The test report shall include: value of the force F, distance of the crushed region to the end of the sample, electrical loptical tests and their requirements, number of tests performed, temperature, sample length, passlfail criteria. BS EN 50289-3-5:2001 BSI 389 Chiswick High Road Lo

30、ndon w4 4fu -.- -=- v-=-. _ -A -A BSI - BrZsh Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are up

31、dated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this Briti

32、sh Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the

33、latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for interna

34、tional standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Tech

35、nical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and

36、receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI website at httr,:/www.bsi-. Copyright Copyright subsists in all B

37、SI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - ele

38、ctronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.