EN 14223-2005 952 Flexible sheets for waterproofing - Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles - Determination of water absorption.pdf

《EN 14223-2005 952 Flexible sheets for waterproofing - Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles - Determination of water absorption.pdf》由会员分享，可在线阅读，更多相关《EN 14223-2005 952 Flexible sheets for waterproofing - Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles - Determination of water absorption.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 14223:2005Flexible sheets for waterproofing Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles Determination of water absorptionThe European Standard EN 14223:2005 has the status of a British StandardICS 91.100.50g49g50g3g38g50g51g60g44g4

2、9g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or netwo

3、rking permitted without license from IHS-,-,-BS EN 14223:2005This British Standard was published under the authority of the Standards Policy and Strategy Committee on 16 January 2006 BSI 16 January 2006ISBN 0 580 47671 5National forewordThis British Standard is the official English language version

4、of EN 14223:2005.The UK participation in its preparation was entrusted to Technical Committee B/546, Flexible sheets for waterproofing, to Subcommittee B/546/9, Bridge deck waterproofing, which has the responsibility to: A list of organizations represented on this committee can be obtained on reques

5、t to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Elect

6、ronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to un

7、derstand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK.Summary of pagesThis document comprises a

8、 front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsCopyright European Committee for Standa

9、rdization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 14223December 2005ICS 91.100.50English VersionFlexible sheets for waterproofing - Waterproofing of concretebridge decks

10、 and other concrete surfaces trafficable by vehicles- Determination of water absorptionFeuilles souples dtanchit - Etanchit des ponts etautres surfaces en bton circulables par les vhicules -Dtermination de labsorption deauAbdichtungsbahnen - Abdichtungen fr Betonbrcken undandere Verkehrsflchen auf B

11、eton - Bestimmung derWasserabsorptionThis European Standard was approved by CEN on 26 October 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to

12、-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the

13、 responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ir

14、eland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050

15、Brussels 2005 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14223:2005: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license f

16、rom IHS-,-,-EN 14223:2005 (E) 2 Contents Page Foreword 3 1 Scope. 4 2 Normative references. 4 3 Terms and definitions 4 4 Test method 4 4.1 Principle 4 4.2 Apparatus and materials 4 4.3 Preparation of test specimens. 5 4.4 Drying and conditioning of the test specimens . 5 4.5 Procedure 5 4.6 Express

17、ion of results . 5 4.6.1 Calculation 5 4.6.2 Precision . 6 4.7 Test report. 6 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 14223:2005 (E) 3 Foreword This document (EN 14223

18、:2005) has been prepared by Technical Committee CEN/TC 254 “Flexible sheets for waterproofing”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2006,

19、and conflicting national standards shall be withdrawn at the latest by June 2006. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Eston

20、ia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Copyright European Committee for Standardization Provided by IHS under license with

21、CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 14223:2005 (E) 4 1 Scope This European Standard specifies a test method for the determination of water absorption in reinforced bitumen sheets which could influence the functional behaviour of these sheets. NOTE

22、 It is primarily the reinforcements ability to absorb water which is examined by this test. 2 Normative references The following referenced documents are indispensable for the application of this European Standard. For dated references, only the edition cited applies. For undated references, the lat

23、est edition of the referenced document (including any amendments) applies. EN 13416, Flexible sheets for waterproofing Bitumen, plastic and rubber sheets for roof waterproofing Rules for sampling prEN 14695, Flexible sheets for waterproofing Reinforced bitumen sheets for waterproofing of concrete br

24、idge decks and other concrete surfaces trafficable by vehicles Definitions and characteristics ISO 5725-2, Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method 3 Terms and

25、 definitions For the purposes of this European Standard, the terms and definitions given in EN 13416, prEN 14695 and the following apply. 3.1 water absorption increase in mass of test specimen after immersion in water expressed as a percentage 4 Test method 4.1 Principle The water absorption of the

26、reinforced bitumen sheet is measured after the test specimen has been immersed in water for a defined period and determined as the increase in mass of the test specimen. 4.2 Apparatus and materials a) Balance, capable of measurements to the nearest 0,1 g. b) Water bath, capable of maintaining a temp

27、erature of (23 3) C. c) Chamber (or laboratory), capable of maintaining a temperature of (23 3) C and (50 5) % RH. d) Distilled water, or de-ionized water. e) Equipment for hanging test specimens, without damaging the specimens. f) Steel wire brush, medium hard. Copyright European Committee for Stan

28、dardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 14223:2005 (E) 5 g) Oven with circulating air, (without fresh air supply) and capable of maintaining a temperature of (50 3) C. 4.3 Preparation of test specimens Ta

29、ke samples in accordance with EN 13416. The test specimens shall be taken at random and at least 1 m from the end of the roll and 100 mm from the edge of the sheet. Five test specimens with dimensions of (200 1) mm x (200 1) mm shall be prepared for testing. If the reinforced bitumen sheet has a sur

30、facing of fine mineral or granules, the surface shall be brushed gently with a steel wire brush to remove any loose mineral or granule. Should problems with heterogeneous results occur (4.6.2) due to surfacing of fine mineral or granules, test specimens may be taken from parts free from such surfaci

31、ng. The test specimen area shall be the same as described above. 4.4 Drying and conditioning of the test specimens Dry the test specimens for 24 h 30 min at (50 3)C and then condition them for 1 h 5 min at (23 3)C and (50 5) % RH before testing. During drying and conditioning the test specimens are

32、placed hanging vertically with a space of at least 20 mm between test specimens. 4.5 Procedure 4.5.1 Weigh the test specimen (m1) and then immerse it in water for 28 days 4 h at (23 3)C. The test specimen shall be placed hanging vertically in the water with a space of at least 20 mm between test spe

33、cimens. The entire area of the test specimen shall be covered with water during the entire test period. 4.5.2 After the 28 days of immersion in water, air dry the test specimen for 5 h 5 min at (23 3)C and (50 5) % RH. During air drying the test specimen shall be placed hanging vertically with a spa

34、ce of at least 20 mm between the test specimens. The set of five test specimens shall be placed in the laboratory with a free space of air surrounding it (at least 0.5 m on each side). 4.5.3 Reweigh the test specimen (m2). 4.6 Expression of results 4.6.1 Calculation The water absorption w for each t

35、est specimen (expressed as a percentage by mass) shall be calculated using equation (1) 211100mmwm= (1) where: m1 is the mass of the test specimen after drying and conditioning; m2is the mass of the test specimen after immersion in water for 28 days and drying for 5 h. The water absorption mean valu

36、e of the five test specimens shall be calculated and recorded. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 14223:2005 (E) 6 4.6.2 Precision The repeatability r and the rep

37、roducibility R is determined by: r = 0,0995w + 0,0766 R = 0,154w + 0,1048 where w is the water absorption, in % by mass. Based on the given repeatability, the test shall be repeated if the difference between wmaxand wminis higher than 0,3098wmean+ 0,2385. NOTE Precision data are based on a ring test

38、 performed in accordance with ISO 5725-2 for water absorption values between 0,2 % and 5,1 % by mass. 4.7 Test report The test report shall include at least the following information: a) all details necessary to identify the product tested; b) reference to this European Standard and any deviation fr

39、om it; c) information about sampling, preparation, drying and conditioning of test specimens in accordance with 4.3 and 4.4; d) information about the procedure in accordance with 4.5; e) test results in accordance with 4.6; f) date of tests. Copyright European Committee for Standardization Provided

40、by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-blankCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 14223:2

41、005BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are

42、 updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this Bri

43、tish Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically

44、 receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/w

45、ww.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international sta

46、ndards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing

47、members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regard

48、ing online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitte