EN 13087-1-2000 en Protective Helmets - Test Methods - Part 1 Conditions and Conditioning (Incorporates Amendment A1 2001)《防护帽的试验方法 第1部分 条件和调节 包含修改件A1-2001》.pdf

《EN 13087-1-2000 en Protective Helmets - Test Methods - Part 1 Conditions and Conditioning (Incorporates Amendment A1 2001)《防护帽的试验方法 第1部分 条件和调节 包含修改件A1-2001》.pdf》由会员分享，可在线阅读，更多相关《EN 13087-1-2000 en Protective Helmets - Test Methods - Part 1 Conditions and Conditioning (Incorporates Amendment A1 2001)《防护帽的试验方法 第1部分 条件和调节 包含修改件A1-2001》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD Protective helmets Test methods Part 1: Conditions and conditioning The European Standard EN 13087-1:2000, with the incorporation of amendment A1:2001, has the status of a British Standard ICs 13.340.20 BS EN 13087-1 12000 Incorporating Amendment No. I Wk present to the responsible

2、European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations represented on this committee can be obtained on request to its secret

3、ary. Cr oss-r e fer enc e s The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Stan

4、dards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pa

5、ges This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 7 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No I Date I Comments 13597 I22 March 2002 I Ad

6、dition of Annex ZA OBSI 22 March 2002 ISBN O 580 34244 I EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13087-1 March 2000 +Al December 200 1 ICs 13.340.20 English version Protective helmets -Test methods - Part 1 : Conditions and conditioning (includes amendment A1:200 1) Casques de protectio

7、n -Mthodes dessai Partie 1: Conditions et conditionnement (inclut lamendement Al :200 1) Schutzhelme - Prfverfahren - Teil 1 : Bedingungen und Vorbehandlung (enthlt nderung A1:2001) This European Standard was approved by CEN on 14January2000. Amendment Al :200 1 was approved by CEN on 2 1 October 20

8、0 1. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained

9、on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretari

10、at has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN Europe

11、an Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels O 2000 CEN AU rights of exploitation in any form and by any means reserved worldwide for CEN national Member s. Ref. No. EN 13087-1:2000 +A1:2001 E

12、EN 13087-1 12000 Foreword This European Standard has been prepared by Technical Committee CEN/TC 158, Head protection, the Secretariat ofwhich is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the

13、 latest by September 2000, and conflicting national standards shall be withdrawn at the latest by September 2000. This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Direct

14、ive(s). According to the CENKENELEC Internal Regulations, the national standards organizations ofthe following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Nether lands, Norw

15、ay, Portugal, Spain, Sweden, Switzerland and the United Kingdom. This European Standard is the first part of EN 13087 which supports essential requirements of EU Directive(s) and consists of ten parts as follows: -Part 1 : Conditions and conditioning. -Part 2: Shock absorption. -Part 3: Resistance t

16、o penetration. -Part 4: Retention system effectiveness. -Part 5: Retention system strength. - Part 6: Field of vision. -Part 7: Flame resistance. -Part 8: Electrical properties. -Part 9: Mechanical rigidity. -Part 10: Resistance to radiant heat. Foreword to amendment Al This amendment EN 13087-1:200

17、0/A1:2001 to EN 13087-1:2000 has been prepared by Technical Committee CENEC 158, Head protection, the Secretariat of which is held by BSI. This amendment to the European Standard EN 13087-1:2000 shall be given the status of a national standard, either by publication of an identical text or by endors

18、ement, at the latest by June 2002, and conflicting national standards shall be withdrawn at the latest by June 2002. This amendment to the European Standard EN 13087:2000 has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports e

19、ssential requirements of EU Directive(s). For relationship with EU Directive(s), see infamative Annex ZA, which is an integral part of this standard. According to the CENKENELEC Internal Regulations, th e nati onal st an dards organizations of the following countries are bound to implement this Euro

20、pean Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. 2 O BSI 22 March 2002 EN 13087-1 12000 Contents Foreword 1 2 3 4 4.1 4.2 4.3 4.4 4.5 4.6

21、4.7 Scope Terms and definitions Prerequisites Test methods General Testing atmosphere Conditioning cabinet High temperature conditioning Low temperature conditioning Water conditioning Artificial ageing Page 2 4 4 4 4 4 4 4 4 4 5 5 Annex A (informative) Artificial ageing - Procedure 6 Annex ZA (info

22、rmative) Clauses of this European Standard addressing essential requirements or other provisions of EU Directives 7 3 O BSI 22 March 2002 EN 13087-1 12000 Intro duct ion This standard is intended as a supplement to the specific product standards for protective helmets (helmet standards). This method

23、 or other test methods may be applicable to specifications for complete helmets or parts thereof, and may be referenced in the appropriate helmet standards. Performance requirements are given in the appropriate helmet standard, as are such prerequisites as the number of samples, pre-conditioning, pr

24、eparation of samples for the tests, sequence and duration oftesting and assessment of test results. If deviations from the test method given in this standard are necessary, these deviations will be specified in the appropriate helmet standard. 1 Scope This European Standard describes methods of test

25、 for protective helmets. The purpose of these tests is to enable assessment of the performance of the helmet as specified in the appropriate helmet standard. This European Standard specifies conditions and conditioning to be used when testing protective helmets. 2 Terms and definitions For the purpo

26、ses ofthis European Standard, terms and definitions used in this standard may be found in the appropriate helmet standard. 3 Prerequisites In order to implement this European Standard, at least the following parameters shall be specified in the appropriate helmet standard: a) number of samples; b) p

27、reparation of samples; c) sequence of conditioning; d) sequence of tests; e) temperatures to be used. 4 Test methods 4.1 General Several methods are specified. The appropriate helmet standard will state which of these method(s) idare applicable. 4.2 Testing atmosphere Testing in accordance with all

28、parts ofEN 13087 shall be performed in an atmosphere with a temperature of (22 * 5) “C and a relative humidity of (55 * 30) YO. This atmosphere may be referred to as laboratory ambient conditions. 4.3 Conditioning cabinet The temperature and artificial ageing conditioning cabinets shall be sufficien

29、tly large to ensure that the helmets do not touch one another or the sides of the cabinet. They shall be fitted with a fan to ensure effective air circulation. 4.4 High temperature conditioning Samples shall be maintained at one of the following temperatures, as specified in the appropriate helmet s

30、tandard, for a period of time between 4 h and 24 h: (+50 or +40) “C with a tolerance of *2 “C in each case. 4.5 Low temperature conditioning Samples shall be maintained at one of the following temperatures, as specified in the appropriate helmet standard, for a period of time between 4 h and 24 h: (

31、O, -10, -20, -30,-40) OC, with a tolerance of %2 “C in each case. 4 O BSI 22 March 2002 EN 13087-1 12000 4.6 Water conditioning Samples shall be water conditioned by one ofthe following methods, as specified in the appropriate helmet standard. Tap water at a temperature not greater than 27 “C shall

32、be used for both methods. Method 1. The sample shall be totally immersed in water for a period of time between 4 h and 24 h. Method 2. The sample shall be sprayed over its outer surface at a rate ofnominally 1 l/min for a period of time between 4 h and 24 h. 4.7 Artificial ageing 4.7.1 Principle The

33、 sample helmet is exposed to a specified irradiation from a xenon arc lamp. 4.7.2 Ayy u ru tus A fused silica envelope, high pressure xenon lamp of450 watt nominal power, operated in accordance with the lamp manufacturers instructions. A means to ensure that the air temperature, measured at the samp

34、le position, does not exceed 50 “C. A means to support the helmets so that they are exposed to the radiation. 4.7.3 Procedure Secure the helmet so that the plane tangential to the crown of the helmet is perpendicular to the direction of radiation from the lamp and the distance between the crown of t

35、he helmet and the arc of the lamp is (150 * 5) mm. Expose the sample to the radiation for (400 * 4) h Remove the sample and allow it to return to laboratory ambient conditions (4.2). NOTE 1 A suitable lamp reference is xB0-450W/4. NOTE A further method for artificial ageing is described in Annex A.

36、5 O BSI 22 March 2002 EN 13087-1 12000 Annex A (informative) Artificial ageing -Procedure The helmet submitted to artificial ageing should be exposed to the radiation of a xenon arc lamp. The radiant energy of the lamp should be filtered to provide a spectral power distribution that closely approxim

37、ates that of terrestrial daylight. The helmet should be fixed on a cylindrical holder concentric to the lamp and which rotates at a speed of 1 to 5 r/min around its axis. Each helmet which will subsequently be tested for shock absorption or for penetration should be orientated so that the area oftes

38、t should be directed towards the lamp. The plane tangential to the shell at this point should be normal to a radius of the cylindrical holder. The radiant energy incident in the plane of the test areas should be either measured or calculated from information provided by the manufacturer of the test

39、apparatus. The exposure interval should be adjusted so that the exposed samples receive a total energy of 1 GJ/m2 over the wavelength range 280 to 800 nm. The samples should be sprayed with distilled or demineralized water (having a conductivity below 5 mS/cm) intermittently with a cycle of 18 min o

40、f spraying and 102 min without spraying. During the latter periods the measured relative humidity should be (50 * 5) YO. The temperature within the test chamber should be measured with a black standard thermometer placed at the same distance from the lamp as the exposed test areas of the helmets. Th

41、e temperature should be maintained at (70 * 3) “C. Ail other test and calibration conditions for the apparatus should be in accordance with IS0 4892-1 and with IS0 4892-2, Method A. NOTE 1 of diameter sufficient to accommodate complete helmets. NOTE 2 NOTE 3 acceptable intensities in the sample surf

42、ace plane required by this procedure. Not all available test apparatus, otherwise meeting the requirements of IS0 4892, will incorporate sample holder frames The position of the water sprays may require adjustment in order to avoid interference with the test samples. The energy output ofthe xenon ar

43、cs should be capable ofbeing reduced below normal operational levels, so as to maintain 6 O BSI 22 March 2002 EN 13087-1 12000 EU Directive 89/686/EEC, Annex II Annex ZA (informative) Clauses of this European Standard addressing essential requirements or other provisions of EU Directives Clause of t

44、his standard This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association and supports essential requirements ofEU Directive on personal protective equipment (PPE) 89/686/EEC. WARNING. Other requirements and other EU Directi

45、ves may be applicable to the product(s) falling within the scope of this standard. The following clauses of this standard are likely to support requirements of Directive 89/686/EEC: 2.4 Personal protective equipment subject to ageing 2.12 PPE bearing one or more identification marks directly or indi

46、rectly related to health 4.7, Annex A 4.6 11.3 Comfort and efficiency 14.4, 4.5 Compliance with the clauses of this standard provides one means ofconforming with the specific essential requirements of the Directive concerned and associated EFTA regulations. 7 O BSI 22 March 2002 BS EN 13087-1 12000

47、BSI 389 Chiswick High Road Lon don w4 4AL BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Re vi si ons British Standards are updated by amendment or r

48、evision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would infor

49、m the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: orders&-. Standards are also available from the BSI website at h