EN 12636-1999 en Products and Systems for the Protection and Repair of Concrete Structures - Test Methods - Determination of Adhesion Concrete to Concrete《混凝土结构保护和修缮用产品及系统的试验方法 混凝土.pdf

《EN 12636-1999 en Products and Systems for the Protection and Repair of Concrete Structures - Test Methods - Determination of Adhesion Concrete to Concrete《混凝土结构保护和修缮用产品及系统的试验方法 混凝土.pdf》由会员分享，可在线阅读，更多相关《EN 12636-1999 en Products and Systems for the Protection and Repair of Concrete Structures - Test Methods - Determination of Adhesion Concrete to Concrete《混凝土结构保护和修缮用产品及系统的试验方法 混凝土.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、STD-GSI BS EN L2b3b-ENGL L P lb2Libb7 077bLLi7 733 BRITISH STANDARD Products and systems for the protection and repair of concrete structures - Test methods - Determination of adhesion concrete to concrete The European Standard EN 126361999 has the status of a British Standard ICs 91.080.40 NO COPYI

2、NG WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 12636: 1999 STD*BSI BS EM LZbIb-ENGL I999 Lb24bL9 079LLqB 87T Amd. No. Date BS EN 12636:1999 Comments National foreword This British Standard is the English language version of EN 126361999. The UK participation in its preparation

3、was entrusted by Technical Committee B/517, Concrete, to Subcommittee B/517/8, Repair and protection of concrete, which has the responsibility to: - aid enquirers to understand the text; - present to the responsible European committee any enquiries on the - monitor related international and European

4、 developments and promulgate interpretation, or proposals for change, and keep the UK interests informed them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or Europ

5、ean publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the neces

6、sary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pag

7、es 2 to 11 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. This Bntish Standard, having been prepared under the direction of the Sector Committee for Building and Civil Engineenng. was published under the authonty of the Standards Co

8、mmittee and comes into effect on 15 September 1999 O BSI 09-1999 ISBN O 580 32586 5 STD-BSI BS EN L2b3b-ENGL 1999 D lbZLlbb9 079b1q9 70b = EUROPEAN STANDARD EN 12636 NORME EUROPENNE EUROPISCHE NORM May 1999 ICs 91.10.30 English version Products and s stems for the protection and repair of concrete s

9、tructures - Test met E ods - Determination of adhesion concrete to concrete Produits et systmes pour la protection et la rparation des stnictures en bton - Mthodes dessais - Determination de ladhrence bton sur bton Produckte fir den Schutz und die Instandsetzung von Betontragwerken - Prfverfahren -

10、Bestimmung der Verbundwirkung Beton-Beton This European Standard was approved by CEN on 16 April 1999. CEN members are bound to comply with the CENICENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

11、Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation u

12、nder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, L

13、uxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fur Normung Central Secretariat: rue de Stassart, 36 B-1050 Brussels Q 1999 CEN All rights of exploitation in any for

14、m and by any means reserved worldwide for CEN national Members Ref. No. EN 12636:1999 E STB-BSI BS EN LZb3L-ENGL 3917 I LbZLibbY 07b150 Li28 I Page 2 EN 12636:1999 Foreword This European Standard has been prepared by Technical Committee CEN/TC 104, Concrete (performance, production, placing and comp

15、liance criteria), the Secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 1999, and conflicting national standards shall be withdrawn at the latest by Nov

16、ember 1999. According to the CENICENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands,

17、 Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. It has been prepared by sub-committee 8, Products and systems for the protection and repair of concrete structures, (Secretariat AFNOR). Contents Foreword 1 Scope 2 Normative references 3 Test method 3.1 Hardened concrete to harde

18、ned concrete 3.2 Fresh concrete to hardened concrete 4 Hardened concrete to hardened concrete 4.1 Equipment 4.2 Test procedure 4.3 Test repon 5 Fresh concrete to hardened concrete 5.1 Equipment 5.2 Test procedure 5.3 Test repon Annex A (informative) Bibliography Page 2 3 3 3 3 3 3 3 4 5 5 5 6 8 9 0

19、BSI 09- 1999 Page 3 EN 12636:1999 1 Scope This European Standard describes methods for the measurement of the adhesion of structural bonding agents between fresh or hardened concrete and a hardened concrete substrate. 2 Normative references This European Standard incorporates by dated or undated ref

20、erence, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorpo

21、rated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 196-1, Methods of testing cement - Part i: Determination of strength. EN 1542: 1999, Products and systems for the protection and repair of concrete structures - Test methods - p

22、ull-off test. prEN 1766, Products and systems for the protection and repair of concrete structures - Test methods - Reference concretes for testing. EN 12 189, Products and systems for the protection and repair of concrete structures - Test methods - Determination of open time. 3 Test method 3.1 Har

23、dened concrete to hardened concrete The adhesion between hardened concrete substrates is measured using the results from tensile bending tests performed on pairs of concrete test prisms which have been bonded using the bonding agent under test. For satisfactory performance of the bonding agent, the

24、tensile bending test should result in fracture in the concrete. When fracture occurs within the bond line it is considered that the structural bonding agent has not performed satisfactorily. Alternatively, the tensile bending test can be performed in the presence of a longitudinal clamping force whe

25、re the intended use involves the application of longitudinal prestress. 3.2 Fresh concrete to hardened concrete The method for the determination of the bond strength of fresh concrete adhesively bonded to hardened concrete involves coring through the fresh concrete overlay beyond the bonded surface

26、and into the hardened concrete substrate, and then performing a pull-off test. For satisfactory performance of the bonding agent the pull-off test should result in fracture in the concrete. When fracture occurs within the bond line it is considered that the structural bonding agent has not performed

27、 satisfactorily. 4 Hardened concrete to hardened concrete 4.1 Equipment 4.1.1 Steel moulds, for producing concrete test pieces of size 40 mm x 40 mm x 160 mm conforming to EN 196-1. 4.1.2 Concrete mixer, as in prEN 1766. 4.1.3 Grit blasting equipment. 8 BSI 09- 1999 Page 4 EN 12636:1999 4.1.4 A stop

28、 clock, calibrated in minutes to a maximum of i20 min. 4.1.5 A suitable frame, for clamping the concrete test pieces together, for example, see Figure 1 of EN 12189. 4.1.6 Testing machine, capable of gradually applying a force of up to 20 kN during the tensile bending test. 4.1.7 Steel support frame

29、, support rollers, loading rollers and spreader beam, as shown in Figure i for four point bending test on bonded concrete prisms. 4.1.8 Steel wire brush. 4.2 Test procedure 4.2.1 Sampling material The bonding agent to be tested shall be taken from one production batch. 4.2.2 Number of test specimens

30、 Tensile bending tests shall be conducted on a minimum of three pairs of bonded concrete prisms. 4.2.3 Concrere prisms Concrete test prisms, measuring 40 mm x 40 mm x 160 mm and using reference concrete type MC (0,40) shall be manufactured and cured in accordance with prEN 1766. The test prisms shal

31、l be removed from the water and cut in half to form two prisms, each measuring 40 mm x 40 mm x 80 mm. Saw cutting shall be carried out on a suitable bench such that the flatness of the surface is to within a tolerance of 0,5 mm and spalling of the cut edges does not exceed i %.of the bonded area. Th

32、e sawn concrete surfaces to be bonded shall be cleaned in running water using a steel wire brush and then grit blasted in accordance with prEN 1766. The test pieces shall then be conditioned as defined below depending upon whether bonding is to be carried out on a dry or wet hardened concrete substr

33、ate. 4.2.4 Conditioning The resin and hardener component of the bonding agent shall be conditioned before mixing to the test temperature of (2 1 f 2) OC. Dry surface Condition test components for 48 h at (21 f 2) “C and a RH of (60 i 10) YO. Dust shall be removed by brushing immediately prior to app

34、lication of the bonding agent. Wet surface Condition test components by immersion in water at room temperature for 48 h. The area to be bonded shall be placed in a vertical position for 15 min at (21 f 2) OC and a RH of (60 f IO) % to allow free water to drain off before application of the bonding a

35、gent. Extreme temperatures For testing at extremes of environmental conditions, alternative conditioning and test temperatures as specified by the supplier shall be used. O BSI 09-1999 Page 5 EN 12636:1999 4.2.5 Specimen preparation The components of the bonding agent shall be mixed at the test temp

36、erature and applied in a layer 1 mm thick, to the prepared concrete end faces of both prisms in each pair all in accordance with the manufacturers instructions. Appropriate spacers shall be used to control the thickness of the bonding agent. Immediately, the corresponding faces of the two concrete p

37、risms in each pair shall be placed against the coated face and the two prisms clamped together to achieve a 1 mm to 2 mm thick bond line with no entrapped air voids, The complete assemblies shall then be cured at the test temperature for seven days or such other time that may be specified. 4.2.6 Mea

38、surement At the end of the specified curing period the bonded concrete prisms shall be positioned within the testing machine over a span of 150 mm as shown in Figure 1. The load shall then be applied vertically at the third span points by means of the spreader beam and increased smoothly at the rate

39、 of (50 f 10) Ns until fracture. Alternatively, the tensile bending test may be performed on the pair of bonded concrete prisms in the presence of a longitudinal clamping force, as described in EN 12 189. The load at failure and the position of the failure plane shall be recorded for each pair of pr

40、isms. 4.3 Test report The report shall include the following information: a) identification of all the constituents in the adhesive mix including manufacturers name, code b) the conditioning and test temperature; c) the substrate surface condition, dry or wet; d) curing period in days between bondin

41、g and testing; e) the method of clamping the concrete test pieces together; f) for each pair of bonded prisms: numbers if applicable, type description and date of production; - the elapsed time interval between application of the bonding agent and closing of the joint; - the longitudinal clamping fo

42、rce imposed during the tensile bending test; - the failure load recorded in the tensile bending test; - the position of the failure plane; g) date of the test; h) reference to this European Standard. 5 Fresh concrete to hardened concrete 5.1 Equipment The equipment can be divided in two parts depend

43、ing on choice of test method, i.e. circular bonded dollies or fiiction grip. Friction grip should be used when the thickness of the top layer exceeds 40 mm. a3 BSI 09- I999 Page 6 EN 12636: 1999 5.1.1 Adhesively bonded dollies method (see Figure 2) a) mixer for the repair material as recommended by

44、the manufacturer; b) climaric chambers for the conditions studied; c) vernier callipers accurate to not less than O, 1 mm; d) adhesive, rapid hardening two component epoxy or similar; e) grinding equipment; f) steel wire brush; g) cleaning solvent; h) diamondcore drilling bir, internal diameter of (

45、51 f i) mm. The core bit should have a cutting edge which protrudes from the cylinder by 1 mm to 2 mm (to minimize lateral forces being applied to the test area); accuracy shall be within i2 %. i)pull-offtest equipment, according to EN 1542 with a pulling capacity of at least 10 kN. The The pull-off

46、 equipment shall be capable of applying the load according to EN 1542,3.1, and shall be provided with a measurement device which displays the exerted force by an analogue or digital system. The measurement device shall retain the reading of maximum force exerted, the so-called failure load. The leve

47、l of the failure load should be recorded; j) cylindricalsteel dollies, with a diameter of (50 f 0,5) mm and a height of at least 25 mm. On the side on which the adhesive is to be applied, the dolly shall be flat with a tolerance of Io, 1 mm per 50 mm length. 5.1.2 Friction grip method a) climatic ch

48、ambers for the conditions studied; b) vernier callipers accurate to not less than O, 1 mm; c) diamond core drill with a diameter depending on friction grip used. The core bit should have a cutting edge which protrudes from the cylinder by 1 mm to 2 mm (to minimize lateral forces being applied to the

49、 test area); attachment for the pull-off test equipment, so that an axial tensile force may be smoothly applied to the core. The internal depth of the grip, i.e. the length of the core which can be accommodated above the annular clamp, shall be at least three times the nominal size of the largest aggregate in the composition being gripped, at least 113 of the thickness of the bonded layer and at least 114 of the diameter of the core; e) pull-off test equipment according to EN 1542 with a pulling capacity of at least 1 O kN. The accuracy shall be within I2 %. The pull-o