ECA EIA-364-105B-2015 TP-105B Altitude C Low Temperature Test Procedure for Electrical Connectors and Sockets.pdf

《ECA EIA-364-105B-2015 TP-105B Altitude C Low Temperature Test Procedure for Electrical Connectors and Sockets.pdf》由会员分享，可在线阅读，更多相关《ECA EIA-364-105B-2015 TP-105B Altitude C Low Temperature Test Procedure for Electrical Connectors and Sockets.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、 EIA STANDARD TP-105B Altitude Low Temperature Test Procedure for Electrical Connectors and Sockets EIA-364-105B (Revision of EIA-364-105A) January 2015 Electronic Components Industry Association ANSI/EIA-364-105-B(2015) Approved: January 26, 2015 EIA-364-105B NOTICE EIA Engineering Standards and Pu

2、blications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his particula

3、r need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their voluntary use by

4、those other than ECIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, ECIA does not assume any liability to any patent

5、 owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This standard is based upon the major technical content of International Electrotechnical Commission standard 60512-11-2 (was IEC 512-6, test 11b), Combined/sequential cold, low air pressure and damp

6、heat, 2002-02. It conforms in all essential respects this IEC standard. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health pr

7、actices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 5326.06, formulated under the cognizance of the CE-2.0 Committee on EIA National Connector and Sockets Standards.) Published by Electronic Components Industry Association 2015 EIA Standa

8、rds see 3.1 5.2 Number of contacts and sealing plugs; see 3.1 5.3 Wire end preparation (location in chamber); see 3.1 5.4 Connector accessories, support hardware to be installed on connector specimen during test; see 3.1 EIA-364-105B Page 3 5.5 Connector specimen preparation; see 3.2 5.6 Test voltag

9、es for altitude, dielectric withstanding voltage, maximum leakage current, and test voltage application time, if other than 5 seconds; see 4.1.6. 5.7 Chamber pressure, temperature and duration of each cycle. 6 Documentation Documentation shall contain the details specified in clause 5, with any exce

10、ptions, and the following: 6.1 Title of test 6.2 Specimen description include fixture, if applicable 6.3 Test equipment used, and date of last and next calibration 6.4 Test procedure 6.5 Values and observations 6.5.1 Chamber pressure, temperature and duration of each cycle 6.5.2 Insulation resistanc

11、e values and identity of each contact pair in test specimen 6.5.3 Dielectric withstanding test results and identity of each contact pair specimen 6.5.4 Connector visual examination 6.6 Name of operator and start/finish dates of test ECIA Document Improvement Proposal If in the review or use of this

12、document, a potential change is made evident for safety, health or technical reasons, please fill in the appropriate information below and mail or FAX to: Electronic Components Industry Association EIA Standards & Technology Department 2214 Rock Hill Rd., Suite 265 Herndon, VA 20170 FAX: (571-323-02

13、45) Document No.: Document Title: Submitters Name: Telephone No.: FAX No.: e-mail: Address: Urgency of Change: Immediate: At next revision: Problem Area: a. Clause Number and /or Drawing: b. Recommended Changes: c. Reason/Rationale for Recommendation: Additional Remarks: Signature: Date: FOR ECIA US

14、E ONLY Responsible Committee: Chairman: Date comments forwarded to Committee Chairman: Revision History Revision letter Project number Publication date Additions, changes and deletions - SP-4302 April 1999 Initial publication A SP-5163 February 2008 Revised paragraph 4.1.1, 4.1.2, 4.1.3, 4.1.6, 5.6 and 6.6B SP-5326.06 - Add paragraph 5.7 Electronic Components Industry Association 2214 Rock Hill Road, Suite 265 * Herndon, VA 20170 * tel 571-323-0294 * fax 571-323-0245 www.ecianow.org