DOD A-A-54747-1992 BANDAGE FELT ORTHOPEDIC (RAYON)《整形外科的绷带(人造丝)》.pdf

《DOD A-A-54747-1992 BANDAGE FELT ORTHOPEDIC (RAYON)《整形外科的绷带(人造丝)》.pdf》由会员分享，可在线阅读，更多相关《DOD A-A-54747-1992 BANDAGE FELT ORTHOPEDIC (RAYON)《整形外科的绷带(人造丝)》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-54747 65 m 9999974 0087606 568 m , I INCH-POUND 1 15 September 1992 A-A-54 7 4 7 COMMERCIAL ITEM DESCRIPTION BANDAGE, FELT, ORTHOPEDIC, (RAYON) The General Services Administration has authorized the use of this Commercial Item Description. Salient Characteristics: Shall be viscose rayon felt ban

2、dage suitable for padding under orthopedic casts. Bandages shall be of the following sizes: SIZE 1 2 3 WIDTH (INCHES) +/- 1/4 INCH 3 4 6 Bandages shall have a minimum average length of 4 yards. Bandages shall consist of the following materials and composition: Shall be fully bleached, clean, dull, c

3、rimped viscose rayon or a mixture of 50 percent fully bleached, clean, dull, crimped, viscose rayon and 50 percent fully bleached, clean, bright, crimped, viscose rayon. Not less than 70 percent, by weight, of fibers shall be 3/4 inch (19 mm) or greater in length; and not more than 5 percent, by wei

4、ght, of the fibers shall be 1/4 inch (6 mm) or less in length. Fibers shall have a denier between 2.7 and 3.3. The rayon fibers shall be mechanically locked and entangled. AMSCNA FSC 6510 DISTRIBUTION STATEMENT A, Approved for public release; distribution is unlimited. O Provided by IHSNot for Resal

5、eNo reproduction or networking permitted without license from IHS-,-,-A-A-54747 b5 9999974 O087607 4T4 A-A-54 7 4 7 Bandages shall meet the following requirements of Absorbent Gauze, USP: Absorbency. The roll shall completely submerge in not more than 30 seconds. Water extract (residue weight prior

6、to ignition) shall not exceed 1.0 percent. Residue on ignition shall not exceed 2.0 percent. Acid or Alkali. The material shall have a minimum weight of 60 grams per square yard when determined in accordance with method 5041 of Federal Test Method Standard No. 191. The average of two diameters of an

7、y roll shall be 2-1/8 to 2-3/4 inches. The average diameter of the roll shall be determined without compressing, by taking the visual minimum diameter, and then by taking the diameter at right angles to the minimum diameter. The finished surface of the finished material shall be either smooth or mic

8、ro-pleated. The bandages shall be in one continuous piece and neatly rolled. The finished bandages shall be capable of adhering to themselves and shall conform to the contour of the body or limb to which they are applied. Bandages shall not slip or roll up under plaster casts nor cause constriction

9、nor have tourniquet effect on the body or limb to which they are applied. Bandages shall be free of lumps, tears, holes and cuts. Bandages shall be substantially free of oil spots, streaks, dirt and foreign matter. Bandages shall not fray when applied nor during use. Workmanship. The bandages shall

10、be free from defects which detract from their appearance or impair their serviceability. Unit. Package (PG). For Size 1, and Size 2, one package containing 72 bandages of one size only, as specified, constitutes one unit. For Size 3, one package containing 36 bandages, as specified, constitutes one

11、unit. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-54747 b5 9999974 OO87bO8 330 A-A-54 7 4 7 e Oualitv Assurance Provisions. Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is respo

12、nsible for the performance of all inspection requirements as specified herein. purchase order, the contractor may use his own or any facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. Government reserves the right to perform

13、 any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. Except as otherwise specified in the contract or The Records. Records of examinations and tests performed by or for the contractor sh

14、all be maintained by the contractor and made available to the Government upon the Governments request, at any time, or from time to time, during the performance of the contract and for a period of three years after delivery of the supplies to which such records relate. Inspection. Inspection, as use

15、d herein, is defined as both examination (such as visual or auditory investigation without the use of special laboratory appliances or procedures) and testing (determination by technical means of physical and chemical 0 properties) of the item. Examination. Examination shall be conducted to determin

16、e compliance with specification requirements. Tests. Tests shall be conducted to determine compliance with specification requirements. shall be used for the determination of two or more test characteristics. Where feasible, the same sample Contractor certification. maintain substantiating evidence t

17、hat the product offered meets the salient characteristics of this Commercial Item Description, and that the product conforms to the producers own drawings, specifications, standards, and quality assurance practices. The government reserves the right to require proof of such conformance prior to firs

18、t delivery and thereafter as may be otherwise provided for under the provisions of the contract. The contractor shall certify and 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-54747 b5 m 9999974 0087b09 277 m A-A-5 4 7 4 7 Metric Products. Pr

19、oducts manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, providing they fall within the tolerance specified using conversion tables contained in the latest revision of Federal Standard No. 376, and all other requirements of this do

20、cument are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerance specified in the inch/pound units, a request should be made to the contracting officer to determine if the product is acceptable. The contracting officer has the option of accepting or rejecti

21、ng the product. Recrulatory reauirements. Federal Food, Drua and Cosmetic Act. If the product covered by this document has been determined by the U.S. Food and Drug Administration to be under its jurisdiction, the offeror/contractor shall comply, and be responsible for compliance by its subcontracto

22、rs/suppliers, with the requirements of the Federal Food, Drug and Cosmetic Act, as amended, and regulations promulgated thereunder. In addition, the offeror/contractor shall comply, and be responsible for compliance by its subcontractors/suppliers, with the requirements of all other applicable Feder

23、al, State, and local statutes, ordinances, and regulations. Recovered materials. The offeror/contractor is encouraged to use recovered material in accordance with Federal Acquisition Regulation Subpart 23.4 to the maximum extent practical. Preservation, packaqinq, p ackinq, labelinq and markinq. Unl

24、ess otherwise specified, preservation, packaging, and packing shall be to a degree of protection to preclude damage to containers and/or contents thereof under normal shipping conditions, handling, etc., involving shipment from the supply source to the receiving activity, plus reshipment from receiv

25、ing activity, and shall conform to applicable carriers rules and regulations. Intermediate and exterior package quantities and labeling and marking shall be as specified in the contract and/or order. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

26、A-A-54747 65 m 9999974 0087630 T99 m Ordering data. labeling and marking must be specified in the contract and/or order. NOTE: Intermediate/exterior package quantities and The following National Stock Numbers are covered by this document : - NSN 6510-00-817-2632 6510-00-817-2633 6510-00-817-2634 MIL

27、ITARY INTERESTS: Custodians: Army - MD Navy - MS Air Force - 03 ITEM IDENTIFICATION SIZE BANDAGE, FELT, ORTHOPEDIC, 6 inches by 4 yards, 36s BANDAGE, FELT, ORTHOPEDIC, 3 inches by 4 yards, 72 BANDAGE, FELT, ORTHOPEDIC, 4 inches by 4 yards, 72s PREPARING ACTIVITY: DOD - MB CIVIL AGENCY COORDINATING ACTIVITY: VA-OSS FDA-MPQAS USPHS Agent : DLA-DM PGC 05206 5 Project No. 6510-0844 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-