DOD A-A-54479-1991 HEELS ORTHOPEDIC CAST《整形外科的跟部》.pdf

《DOD A-A-54479-1991 HEELS ORTHOPEDIC CAST《整形外科的跟部》.pdf》由会员分享，可在线阅读，更多相关《DOD A-A-54479-1991 HEELS ORTHOPEDIC CAST《整形外科的跟部》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-54479 65 9999974 O062375 b TYPE A-A-54 4 7 9 30 August 1991 COMMERCIAL ITEM DESCRIPTION HEELS, ORTHOPEDIC, CAST The General Services Administration has authorized the use of this Commercial Item Description as a replacement for Military Specification MIL-H-37577 which is cancelled. This Commerci

2、al Item Description covers an adult size walking heel for incorporation into an orthopedic cast of the lower leg. Salient characteristics: General. The orthopedic heels covered herein shall be of the following types: DESCRIPTION I Firm walking surface: triangle design tread. II Medium firm walking s

3、urface: fine serrated tread. III Firm walking surface: coarse serrated tread. IV Resilient walking surface: diamond design tread. Material. Heel types I, II, and IV shall be molded from either natural or synthetic rubber compound that is suitable in all respects for the purpose intended. Heel type I

4、II shall be molded from ethylene propylene terpolymer that is suitable in all respects for the purpose intended. AMSC N/A DISTRIBUTION STATEMENT . Approved for public re distribution is unlimitea. FSC 6515 ease: Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

5、m IHS-,-,-A-A-54 4 7 9 Phvsical properties. The physical properties of the material shall be shown in table 1 below: Table 1. Physical Properties. Tensile Durometer strength Hardness (min. Elongation minimum Type Material (shore A) Psi) I Rubber 65-75 1000 350% II Rubber 50-65 1700 400% III Plastic

6、65-75 1500 700% IV Rubber 55-65 750 320% I Style, desiqn, and dimensions. The heels shall be in accordance with the following Defense Personnel Support Center (DPSC) Drawing Numbers: TYPE DPSC Drawinq No. I 23184 II 23181 III 23182 IV 23183 Heels shall be molded of one piece construction. Color and

7、markinq. The color of the heels shall be the manufacturers commercial color except black and other floor marking colors. Identification markinq and labelina. The heels shall be legibly marked with the contractors name or trademark. Foreign manufactured heels shall bear the name of the country of ori

8、gin. Workmanship. detract from its appearance or impair its serviceability. The heels shall be free from defects which 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-54479 65 9999974 0062377 T Unit. Each (EA). One heel, of the type constitutes

9、 one unit. A-A-54 4 7 9 specified, 9UALITY ASSURANCE PROVISIONS. Responsibility for inspection. Unless o,herwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except otherwise specified in the contra

10、ct or purchase order, the contractor may use his own or any facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such ins

11、pections are deemed necessary to assure supplies and services conform to prescribed requirements. Records. Records of examinations and tests performed by or for the contractor shall be maintained by the contractor and made available to the Government upon request, at any time, or from time to time,

12、during the performance of the contract and for a period of three years after delivery of the supplies to which such records relate. Inspection. Inspection, as used herein, is defined as both examination (such as visual or auditory investigation without the use of special laboratory appliances or pro

13、cedures) and testing (determination by technical means and chemical properties) of the 0 item. Samplins for examination. Sampling for examination shall be conducted in accordance with MIL-STD-105, and as specified . herein. heel. Sampling shall be Inspection level II with an acceptable quality level

14、 (AQL) of 1.0. Unit of product for examination purposes shall be one Examination. Samplina for tests. Examination shall be conducted to determine compliance with specification requirements. Sampling for tests shall be conducted in accordance with.MIL-STD-105 and as specified herein. product for test

15、 purposes shall be one heel. Sampling shall be Inspection level S-2 with an AQL of 1.0. Unit of Tests. Tests shall be conducted to determine compliance with specification requirements. Where feasible, the same sample shall be used for the determination of two or more text characteristics. 3 Provided

16、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-(A-A-54479 65 9999974 00b237 L Si _ A-A-54 4 7 9 Contractor certification. The contractor shall certify that the product offered meets the salient characteristics of this description and conforms to the produce

17、rs own drawings, specifications, standards, and quality assurance practices. The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. Metric Droducts. Products manufactured to

18、metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, providing they fall within the tolerance specified using conversion tables contained in the latest revision of Federal Standard No. 376, and all other requirements of this document are met. If a pr

19、oduct is manufactured to metric dimensions and those dimensions exceed the tolerances specified in the inch/pound units, a request should be made to the contracting officer to determine if the product is. acceptable. The contracting officer has the option of accepting or rejecting the product. Resul

20、atorv reauirements. Federal Food, Drus, and Cosmetic Act. If the product covered by this document has been determined by the U.S. Food and Drug Administration to be under its jurisdiction , the offeror/contractor shall comply, and be responsible for compliance by its subcontractors/suppliers, with t

21、he requirements of the Federal Food, Drug Cosmetic Act, as amended, and regulations promulgated thereunder. In addition, the offeror/contractor shall comply, and be responsible for compliance by its subcontractors/suppliers, with the requirements of all other applicable Federal State, and local stat

22、utes, ordinances, and regulations. Recovered material. The offeror/contractor is encouraged to use recovered material in accordance with Federal Acquisition Regulation Subpart 23.4 to the maximum extent practical. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license

23、 from IHS-,-,-I l I I I l I I I I I A-A-54479 65 = 9999974 0062379 3 II A-A-54 4 7 9 Preservation. Dackaain ackina, labelina. and markina. Unless otherwise specified, p%:rvation, packaging, and packing shall be to a degree of protection to preclude damage to containers and/or contents thereof under

24、normal shipping conditions, handling, etc:, involving shipment from the supply source to the receiving activity, plus reshipment from receiving activity, and shall conform to applicable carriers rules and regulations. Intermediate and exterior package quantities and labeling and marking shall be as

25、specified in the contract and/or order. labeling and marking must be specified in the contract and/or order. I I Ordering data. Intermediate/exterior package quantities and l NOTE: document : The following National Stock Numbers are covered by this - NSN 6515-00-106-8475 6515-00-106-8476 e 6515-00-1

26、06-8477 6515-00-106-8478 MILITARY INTERESTS: Custodians: Army-MD Navy-MS Air Force-03 ITEM IDENTIFICATION TYPE HEEL ORTHOPEDIC CAST, I Rubber, Orthopedic Equipment Design, Adult Size. Rubber, Zimmer Design, Adult Size. HEEL ORTHOPEDIC CAST, II HEEL ORTHOPEDIC CAST, III Plastic, Stryker Design, Adult Size. Rubber, Wright Design, Adult Size. HEEL ORTHOPEDIC CAST, IV PREPARING ACTIVITY: DoD-MB Agent : DLA-DM CIVIL AGENCY COORDINATING ACTIVITIES: VA-OSS USPHS FDA-MPQAS Project No. 6515-5081 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-