DLA MS39199 REV G-2012 NIPPLE TUBE-SAFETY SLEEVE COMPRESSION TYPE BULKHEAD MOUNTING.pdf
《DLA MS39199 REV G-2012 NIPPLE TUBE-SAFETY SLEEVE COMPRESSION TYPE BULKHEAD MOUNTING.pdf》由会员分享,可在线阅读,更多相关《DLA MS39199 REV G-2012 NIPPLE TUBE-SAFETY SLEEVE COMPRESSION TYPE BULKHEAD MOUNTING.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、AMSC N/A FSC 4730 MS39199G 30 August 2012 SUPERSEDING MS39199F 1 February 2002 DETAIL SPECIFICATION SHEET NIPPLE, TUBE-SAFETY SLEEVE COMPRESSION TYPE, BULKHEAD MOUNTING This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring
2、 the product described herein shall consist of this specification sheet. FIGURE 1. Nipples, tube-safety sleeve compression type, bulkhead mounting. . Inactive for new design after 29 December 1967. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I
3、HS-,-,-MS39199G 2 TABLE I. Nipples, tube-safety sleeve compression type, bulkhead mounting. 1/ 2/ Dash No. Tube OD B C Thread Length D Thread Length E F G H J 1 1/8 5/16 24UNF-2A 7/32 11/16 .135 .139 13/64 1/8 9/32 3/32 2 3/16 3/8 24UNF-2A 7/32 3/4 .196 .200 1/4 5/32 9/32 1/8 3 1/4 1/2 20UNF-2A 21/6
4、4 29/32 .261 .265 19/64 13/64 13/32 13/64 4 5/16 9/16 18UNF-2A 21/64 51/64 .324 .328 19/64 13/64 13/32 13/64 5 3/8 5/8 18UNF-2A 23/64 1-23/64 .386 .390 19/64 13/64 7/16 9/32 6 1/2 3/4 16UNF-2A 11/32 1-11/32 .514 .518 5/16 13/64 7/16 27/64 7 5/8 15/16 16UN-2A 23/64 1-3/8 .641 .645 11/32 15/64 15/32 1
5、/2 8 3/4 1-1/16 16UN-2A 23/64 1-13/32 .766 .770 11/32 13/64 15/32 21/32 9 7/8 1-3/16 16UN-2A 23/64 1-13/32 .891 .895 11/32 13/64 15/32 23/32 10 1 1-5/16 16UN-2A 23/64 1-7/16 1.016 1.020 13/32 13/64 15/32 7/8 11 1-1/4 1-5/8 16UN-2A 7/16 1-35/64 1.270 1.274 13/32 13/64 35/64 1-5/64 12 1-1/2 1-7/8 16UN
6、-2A 15/32 1-23/32 1.520 1.524 31/64 13/64 34/64 1-11/32 TABLE I. Nipples, tube-safety sleeve compression type, bulkhead mounting- Continued. 1/ 2/ K L M N 1/2 1-1/4 1-7/8 1/2 9/16 1-5/16 2 9/16 11/16 1-21/32 2-15/32 11/16 3/4 1-17/32 2-9/32 13/16 13/16 2-1/8 3 13/16 15/16 2-1/8 3-3/16 15/16 1-1/8 2-
7、3/16 3-1/4 1-1/8 1-1/4 2-1/4 3-7/16 1-1/4 1-3/8 2-1/4 3-7/16 1-3/8 1-1/2 2-5/16 3-1/2 1-1/2 1-13/16 2-9/16 3-13/16 1-13/16 2-1/16 2-7/8 4-1/4 2-1/16 1/ Dimensions are in inches. 2/ This illustration is for identification and is not intended to restrict designs or shapes not dimensioned Provided by I
8、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39199G 3 REQUIREMENTS: Dimensions and configuration: See figure 1. Nipples. See table I. Tolerances: Unless otherwise specified, decimals .005, fractions 1/64, degrees 2. Threads: The threads shall be in accordanc
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAMS39199REVG2012NIPPLETUBESAFETYSLEEVECOMPRESSIONTYPEBULKHEADMOUNTINGPDF
链接地址:http://www.mydoc123.com/p-697229.html