DLA MS27142 REV D-2003 CONNECTOR PLUG ELECTRICAL-PIN CONTACT NO 12 14 16 AWG WATERPROOF《12 14 16 AWG防水电动针接触插头连接器》.pdf

《DLA MS27142 REV D-2003 CONNECTOR PLUG ELECTRICAL-PIN CONTACT NO 12 14 16 AWG WATERPROOF《12 14 16 AWG防水电动针接触插头连接器》.pdf》由会员分享，可在线阅读，更多相关《DLA MS27142 REV D-2003 CONNECTOR PLUG ELECTRICAL-PIN CONTACT NO 12 14 16 AWG WATERPROOF《12 14 16 AWG防水电动针接触插头连接器》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、MS27142D 17 June 2003 SUPERSEDING MS27142C 23 October 1984 DETAIL SPECIFICATION SHEET CONNECTOR, PLUG, ELECTRICAL-PIN CONTACT, NO. 12, 14, 16 AWG, WATERPROOF This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the produc

2、t described herein shall consist of this specification. Inches mm Inches mm .003 .005 .010 .015 .079 .135 .160 .235 .076 .127 .254 .381 2.00 3.43 4.06 5.96 .271 .394 .470 .700 .915 1.328 1.421 6.88 10.01 11.94 17.78 23.24 33.73 36.09 FIGURE 1. Configuration and dimensions. AMSC N/A 1 of 3 FSC 5935 D

3、ISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27142D 2 MS dash no. Reference drawing no. (assembly) Size Shell number Washer number Terminal number A Cable

4、 diameter AWG size Cable MIL-DTL-13486 PIN -1 8338571 1 8338572 8338573 MS-27148-1 1.421 .235 .010 12 M13486/1-7 -2 8338565 2 8338566 8338567 MS-27148-2 1.328 .160 .010 14 M13486/1-5 -3 None 3 8724495 8724497 MS-27148-3 1.328 .135 .015 16 M13486/1-3 FIGURE 1. Configuration and dimensions - Continued

5、. REQUIREMENTS: Material: Washer: Brass alloy C24000, C26000 or C26800, temper H02, in accordance with ASTM B 36/B 36M. Shell: Rubber in accordance with ASTM D2000, M3BC610A14C12EO34F19. Mating connectors: Size 1 mates with connector MS 27143. Size 2 mates with connector MS 27144, style 1, size 1. S

6、ize 3 mates with connector MS 27144, style 1, size 2. Electrical requirements: Voltage rating: 30 volts DC. Current rating: AWG size Current (AMPS) 16 13 14 17 12 23 Voltage drop: When connections are coupled, the voltage drop shall not exceed 20 millivolts and shall meet the requirements outlined i

7、n MIL-STD-202, method 307. Dielectric strength: When connectors are coupled, the assembly shall meet the requirements of the dielectric strength test (1000 volts) outlined in MIL-STD-202, method 302. Corrosion test: When connectors are coupled, the assembly shall meet the salt spray corrosion test o

8、utlined in MIL-STD-202, method 101 (5% saline solution, 200 hours duration). Waterproof requirements: When connectors are coupled, the assembly shall be waterproof. Refer to MIL-HDBK-1184, or equivalent, for guidance on waterproof testing. Pull test: The terminal crimped to the cable shall withstand

9、 a pull test of 90 pounds (40 kilograms) on size 1, 60 pounds (27 kilograms) on size 2, and 40 pounds (18 kilograms) on size 3. Separation force: The force required to uncouple the connectors shall not exceed 50 percent of the values expressed in the pull test above at -55C and at 85C. Provided by I

10、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27142D 3 Part or Identifying Number (PIN): MS27142 - (dash number as shown on figure 1). Reference drawings may be obtained from the U.S. Army Tank Automotive Command, Warren, MI., 48090. (Marginal notations are n

11、ot used in this revision to identify changes with respect to the previous issue due to the extent of the changes.) CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Air Force - 99 Navy - MC (Project 5935-4427-001) DLA CC Review activities: Army - CR4 Air Force - 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-