DLA MS25231 REV G-2004 LAMPS INCANDESCENT CENTER CONTACT MINIATURE BAYONET BASE (T-3-1 4 BULB)《(T-3-1 4灯泡)小型卡口灯座接触中心白炽灯》.pdf

《DLA MS25231 REV G-2004 LAMPS INCANDESCENT CENTER CONTACT MINIATURE BAYONET BASE (T-3-1 4 BULB)《(T-3-1 4灯泡)小型卡口灯座接触中心白炽灯》.pdf》由会员分享，可在线阅读，更多相关《DLA MS25231 REV G-2004 LAMPS INCANDESCENT CENTER CONTACT MINIATURE BAYONET BASE (T-3-1 4 BULB)《(T-3-1 4灯泡)小型卡口灯座接触中心白炽灯》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A 1 of 2 FSC 6240 MS25231G 29 April 2004 Superseding MS25231F 23 August 1985 DETAIL SPECIFICATION SHEET LAMPS, INCANDESCENT, CENTER CONTACT, MINIATURE BAYONET BASE (T-3-1/4 BULB) This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The req

2、uirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-6363. 27.6323.8015.8810.929.309.078.247.626.484.571.701.530.840.641.088.9375.625.430.366.357.324.300.255.180.067.061.033.025mmINCHINSULATORPROTRUSION (TYP).033.025.067.061CONTACTS.324.300.255.1

3、80 .366 .357 NOMLCL.625.430MAX.9375MAXLMIN(2 PINS EQUALLY SPACED ON CIRCUMFERENCE)Inactive for new design after 30 November 1998. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS25231G 2TABLE I. Dimensions and dash numbers. REQUIREMENTS:

4、 1. The envelope need not have the shape shown, but the envelope, including any coating thereon, shall be contained within the outline shown. 2. The dash number of the lamp, and the manufacturers trademark or an abbreviation of the manufacturers name, shall be marked on the base of each lamp. 3. Req

5、uirements hereon shall be met with the design voltage listed above, either DC or 400 20 Hertz, applied to the contacts of the lamp. 4. Light emitted by the red lamps shall conform to SAE-AS25050 for aviation red except that it shall not be paler or yellower than NBS No. 3215 filter. The color may be

6、 attained by either colored glass or a coating on the glass. NOTES: 1. Dimensions in inches. 2. Metric equivalents (to the nearest .01 mm) are given for general information only and are based upon 1 inch = 25.4 mm. 3. 313S, 316S AND 1819S lamps are intended for special application in MS25331 Press-T

7、o-Test indicator light assemblies which require minimum lamp length shown for proper operation. 4. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. MILITARY INTEREST Preparing activi

8、ty: DLA - IS Custodians: Army CR4 (Project 6240-1450) Navy - AS Air Force - 99 Review activities: Army AV Navy EC, MC Air Force 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verif

9、y the currency of the information above using the ASSIST Online database at www.dodssp.daps.mil. SUPERSEDES DASH NO. AND TRADE NO. TYPE PER MIL-DTL-6363 L MIN (SEE NOTE 3) DESIGN POTENTIAL (VOLTS) DESIGN CURRENT (AMPERES) COLOR OF BULB LIGHT OUTPUT (SPHERICAL) CANDLEPOWER AVERAGE LIFE AT DESIGN VOLT

10、S (HOURS) MS15571 AN3121 -313 I - CLEAR 3.34 35% -4 -313 -313R I - RED 0.4 APPROX -313R -313S I 1.080 28 .17 CLEAR 3.34 35% -316 I - CLEAR 3.5 25% -316R I - RED 0.4 APPROX -316S I 1.080 6 .70 CLEAR 3.5 25% 500 -1819 I - CLEAR 0.34 35% -6 -1819 -1819R I - RED 0.04 APPROX -1819S I 1.080 CLEAR 0.34 35% -1829 I - 28 .04 .07 CLEAR 1.1 APPROX 1000 -1873 I - 28 .20 CLEAR 3.0 25% 2500 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-