DLA MS17241 REV C-2013 HEAT INTERCHANGER REFRIGERANT - 12.pdf

《DLA MS17241 REV C-2013 HEAT INTERCHANGER REFRIGERANT - 12.pdf》由会员分享，可在线阅读，更多相关《DLA MS17241 REV C-2013 HEAT INTERCHANGER REFRIGERANT - 12.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 4130 MS17241C 7 January 2013 SUPERSEDING MS17241B 21 March 1975 DETAILED SPECIFICATION SHEET HEAT INTERCHANGER, REFRIGERANT - 12 This specification sheet is approved for all Departments and Agencies of the Department of Defense. The requirements for acquiring the described herein shall

2、consist of this specification sheet and procurement specification MIL-H-22832. THE DOTTED LINES REPRESENT ACCEPTABLE LOCATIONS OF CONNECTION ENDS FIGURE 1. HEAT INTERCHANGER. INCH-POUND INACTIVE FOR NEW DESIGN AFTER 21 NOVEMBER 1994. Provided by IHSNot for ResaleNo reproduction or networking permitt

3、ed without license from IHS-,-,-MS17241C 2 TABLE I. Part Numbers and Dimensions. CAPACITY DIMENSIONS FEMALE SOLDER JOINT SIZE PART NO. (MIN) A .500 B (MAX) C D T.R. INCHES INCHES INCHES INCHES MS17241-1 1/12 9.500 1.625 .250 .500 MS17241-2 1/6 11.875 1.625 .250 .500 MS17241-3 1/4 15 2.125 .375 .625

4、MS17241-4 1/3 15 2.125 .375 .625 MS17241-5 1/2 15.250 2.250 ,375 .875 MS17241-6 3/4 14.750 3.125 .375 1.125 MS17241-7 1 15.625 3.625 .500 1.125 MS17241-8 2 15.625 5 .625 1.375 NOTES: 1. Rating conditions: Interchangers shall be capable of raising the suction gas temperature from minus 5 F, at a pres

5、sure corresponding to minus 10 F. Saturated to plus 30 F superheated leaving temperature, with the returning liquid temperature hot higher than 100 F. 2. Materials: Shell brass, copper, aluminum jacketed or steel, corrosion resistant treated. 3. Solder connection ends: Shall be in accordance with AS

6、ME B16.22. 4. Strength: Factory test pressure 235 P.S.I.G. (MIN). Burst pressure (both circuits) 1175 P.S.I.G. (MIN). 5. Pressure drop: Gas circuit 1/4 P.S.I.G. at minus 10 F, evaporated. 1/2 P.S.I.G. at plus 25 F, evaporated. Liquid circuit Negligible. Dimension “A” may be obtained on shorter units

7、 by use of a tube extension supplied with the unit and having the same type end connection. 6. For design feature purposes this specification takes precedence over documents referenced herein. 7. Referenced documents shall be the issue in effect on the date of invitation for bids. 8. Part number: Th

8、e MS part number consists of the MS number plus the dash number. Example: MS 17241-1. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS17241C 3 9. Changes from previous issue. Marginal notations are not used in this revision to identify changes with

9、 respect to the previous issue due to the extent of the changes. Custodians: Preparing Activity: Army GL DLA-IS Navy YD Air Force 99 (Project 4130-2013-001) Review Activities: Army CE, MD Navy MC, SH Air Force 84 DLA-GS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-