DLA MS3443 REV C-2011 CONNECTORS RECEPTACLE ELECTRICAL SOLDER OR WELDED FLANGE MOUNT BAYONET COUPLING SOLDER PIN CONTACT CLASS H SERIES 2.pdf

《DLA MS3443 REV C-2011 CONNECTORS RECEPTACLE ELECTRICAL SOLDER OR WELDED FLANGE MOUNT BAYONET COUPLING SOLDER PIN CONTACT CLASS H SERIES 2.pdf》由会员分享，可在线阅读，更多相关《DLA MS3443 REV C-2011 CONNECTORS RECEPTACLE ELECTRICAL SOLDER OR WELDED FLANGE MOUNT BAYONET COUPLING SOLDER PIN CONTACT CLASS H SERIES 2.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET CONNECTORS, RECEPTACLE, ELECTRICAL, SOLDER OR WELDED FLANGE MOUNT, BAYONET COUPLING, SOLDER PIN CONTACT, CLASS H, SERIES 2 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product descr

2、ibed herein shall consist of this specification sheet and MIL-DTL-26482. NOTE: For “XX”, see note 4 and table I for contact cavities requiring reduced dimensions. FIGURE 1. Receptacle, class H, dimensions and configurations. AMSC N/A FSC 5935 Inactive for new design after 15 December 1998. INCH-POUN

3、D MS3443C 14 January 2011 SUPERSEDING MS3443B 1 March 2007 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3443C 2 FIGURE 1. Receptacle, class H, dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking

4、permitted without license from IHS-,-,-MS3443C 3 Contact size BB CC DD HH KK 20 .041 (1.04) .039 (0.99) .088 (2.24) .061 (1.55) .048 (1.22) .042 (1.07) .188 (4.78) .109 (2.77) .110 (2.79) .068 (1.73) 16 .0635 (1.61) .0615 (1.56) .116 (2.95) .096 (2.44) .075 (1.91) .069 (1.75) .251 (6.38) .172 (4.37)

5、 .141 (3.58) .109 (2.77) 12 .095 (2.41) .093 (2.36) .150 (3.81) .130 (3.30) .122 (3.10) .112 (2.84) .251 (6.38) .172 (4.37) .141 (3.58) .109 (2.77) FIGURE 1. Receptacle, class H, dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without l

6、icense from IHS-,-,-MS3443C 4 Shell size J K L P V Max weight lbs (grams) 8 .156 (3.96) .116 (2.95) .570 (14.48) .801 (20.35) .178 (4.52) .118 (3.00) .248 (6.30) .188 (4.78) .0310 (14.06) 10 .680 (17.27) .0340 (15.42) 12 .789 (20.04) .0400 (18.14) 14 .914 (23.22) .0510 (23.13) 16 1.039 (26.39) .0620

7、 (28.12) 18 1.164 (29.57) .0820 (37.19) 20 1.258 (31.95) .863 (21.92) .1000 (45.36) 22 .188 (4.78) .148 (3.76) 1.383 (35.13) .895 (22.73) .146 (3.71) .086 (2.18) .216 (5.49) .156 (3.96) .1150 (52.25) 24 1.508 (38.30) .2680 (121.56) FIGURE 1. Receptacle, class H, dimensions and configurations - Conti

8、nued. Shell size A C D dia (min ID) F 8 .635 (16.13) .615 (15.62) .563 (14.30) .557 (14.15) .361 (9.17) .598 (15.19) .578 (14.68) 10 .760 (19.30) .740 (18.80) .673 (17.09) .667 (16.94) .489 (12.42) 12 .854 (21.69) .834 (21.18) .782 (19.86) .776 (19.71) .606 (15.39) 14 .979 (24.87) .959 (24.36) .907

9、(23.04) .901 (22.89) .731 (18.57) 16 1.104 (28.04) 1.084 (27.53) 1.032 (26.21) 1.026 (26.06) .856 (21.74) 18 1.228 (31.19) 1.208 (30.68) 1.157 (29.39) 1.151 (29.24) .961 (24.41) 20 1.322 (33.58) 1.302 (33.07) 1.251 (31.78) 1.245 (31.62) 1.086 (27.58) .660 (16.76) .640 (16.26) 22 1.448 (36.78) 1.428

10、(36.27) 1.376 (34.95) 1.370 (34.80) 1.211 (30.76) 24 1.574 (39.98) 1.554 (39.47) 1.501 (38.13) 1.495 (37.97) 1.336 (33.93) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3443C 5 NOTES: 1. Dimensions are in inches. Metric equivalents are given for

11、information only. 2. Dimensional tolerances are .XX .01 inches (0.25 mm) and .XXX .005 inches (0.13 mm). Angular tolerances are X 1. 3. Polarizing stripes, color optional. 4. Insert arrangements requiring reduced diameters for raised seal barrier on outer row of contact cavities as indicated. 5. Tru

12、e position (TP) tolerances specified are in accordance with ASME Y14.5. FIGURE 1. Receptacle, class H, dimensions and configurations - Continued. Inches mm .005 0.13 .010 0.25 .011 0.28 .016 0.41 .020 0.51 .022 0.56 .026 0.66 .047 1.19 .057 1.45 .060 1.50 .088 2.24 .140 3.56 .216 5.49 .278 7.06 Prov

13、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3443C 6 TABLE I. Contact cavities requiring reduced diameters (XX) for pins in outer row of contact cavities. 1/ Shell size Insert arrangement Contact cavities 8 -33 and -98 A, B, C 12 -10 C, G 14 -12 A,

14、B, C, D, E, F, G, H 14 -18 A, C, E, G, J, L 14 -19 B, D, F, H, K, M 16 -26 A, B, C, D, E, F, G, H, J, K, L, M, N, P, R 18 -32 A, B, C, D, E, F, G, H, J, K, L, M, N, P, R, S, T 22 -41 A, B, C, D, E, F, G, H, J, K, L, M, N, P, R, S, T, U, V, W, X, Y 1/ The reduced diameter “XX” refers to the diameters

15、 of the raised seal barriers (pin barrier rings) to ensure proper sealing of pin and socket after mating. See MIL-DTL-26482, connector intermateability control dimensions (series 1 and series 2) figure for reduced diameter “XX” for contact size 20 only. REQUIREMENTS: Dimensions and configuration: Se

16、e figure 1 and table I. Connector mating: This connector mates with MS3475 and MS3476. For insert arrangement: See MIL-STD-1669. Intermateability dimensions are in accordance with MIL-DTL-26482. Material: Shell types A and B, 300 series stainless steel in accordance with ASTM A582/A582M and ASTM A27

17、6 (weld only, not intended for solder applications). Shell type C, cold rolled steel in accordance with ASTM A108 (intended for solder applications only). Finish: Shell types A and B, passivated in accordance with ASTM A967. Shell type C, .0001 inch (2.54 m) tin minimum in accordance with ASTM B545

18、or ASTM B339 over nickel in accordance with SAE AMS-QQ-N-290. The use of pure tin, as an underplate or final finish, is prohibited both internally and externally. Tin content of connectors, their components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 per

19、cent lead, by mass. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3443C 7 MS3443 H 24 C 61 P W MS number Class Shell size Termination type and shell material Insert arrangement Contact style Insert position Supersession data: PIN MS3443H*C* super

20、sedes PINs MS3443H*A* and MS3443H*B*. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies

21、 in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-DTL-26482, this document references the fo

22、llowing: MS3475 MS3476 MIL-STD-1669 ASME Y14.5 ASTM A108 ASTM A276 ASTM A967 ASTM A582/A582M ASTM B339 ASTM B545 SAE AMS-QQ-N-290 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3443C 8 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR

23、DLA - CC Navy - AS Air Force 85 (Project 5935-2011-004) DLA - CC Review activities: Army - AV Navy - EC, SH NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-