SAE AS 85352 4A-2013 INFLATOR ASSEMBLY DUAL CHUCK STEM GAGE KIT《双重查克杆充量装配工具》.pdf

《SAE AS 85352 4A-2013 INFLATOR ASSEMBLY DUAL CHUCK STEM GAGE KIT《双重查克杆充量装配工具》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 85352 4A-2013 INFLATOR ASSEMBLY DUAL CHUCK STEM GAGE KIT《双重查克杆充量装配工具》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD INFLATOR ASSEMBLY DUAL CHUCK STEM GAGE KITAS85352/4Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or oth

2、erwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2002-02REAFFIRMED 2007-12 STABILIZED 2013-10 THIRD AN

3、GLE PROJECTION CUSTODIAN: A-5 REV.AFEDERAL SUPPLY CLASS 6685 AS85352/4REV. APROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits appli

4、cability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsug

5、gestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS85352/4ARATIONALE NEED TO OPEN A PROJECT TO PLACE ON A 28 DAY BALLOT FOR STABILIZATION. NEITHER A-5 NOR AGE-2C PLANS TO MAINTAIN THIS DOCUMENT. STABILIZED NOTICE THIS DO

6、CUMENT HAS BEEN DECLARED “STABILIZED“ BY THE SAE A-5 AEROSPACE LANDING GEAR SYSTEMS COMMITTEE AND WILL NO LONGER BE SUBJECTED TO PERIODIC REVIEWS FOR CURRENCY. USERS ARE RESPONSIBLE FOR VERIFYING REFERENCES AND CONTINUED SUITABILITY OF TECHNICAL REQUIREMENTS. NEWER TECHNOLOGY MAY EXIST. Copyright SA

7、E International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS85352/4 SHEET 1 OF 2 REV. A INFLATOR ASSEMBLY DUAL CHUCK STEM GAGE KIT NOTICETHIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFIC

8、ATION MIL-I-85352/4, NOTICE 1 AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-I-85352/4, NOTICE 1. ANY PART NUMBERS ESTABLISHED BY T

9、HE ORIGINAL SPECIFICATION REMAIN UNCHANGED.THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVI

10、DE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT.UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREM

11、ENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo repr

12、oduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS85352/4 SHEET 2 OF 2 REV. A INFLATOR ASSEMBLY DUAL CHUCK STEM GAGE KIT THIS SPECIFICATION IS APPROVED FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE.THE COMPLETE REQUIREMENTS FOR PROCURING THE DU

13、AL CHUCK STEM GAGES DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE IN EFFECT OF SPECIFICATION MIL-I-85352.REQUIREMENTS:DUAL CHUCK STEM GAGE: THE DUAL CHUCK STEM GAGE SHALL CONSIST OF THE GAGE SHOWN WITH A GAGE ELEMENT CONFORMING TO M85352/3-1 OR M85352/3-2 AS SPECIFIED BY THE P

14、ART NUMBER.PART NUMBER: PART NUMBERS SHALL CONSIST OF THE FOLLOWING:(IN SEQUENCE)1. THE LETTER “M”2. THE GENERAL SPECIFICATION NUMBER3. A SLASH, AND SLASH NUMBER OF THIS SPECIFICATION SHEET4. A DASH, AND THE APPROPRIATE SIZE DASH NUMBERS FROM TABLE ICopyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-