DLA MIL-DTL-83538 13 A-2008 CONNECTORS AND ACCESSORIES ELECTRICAL CIRCULAR UMBILICAL TEST PLUG REMOVABLE CRIMP CONTACTS PINS FOR MIL-STD-1760 APPLICATIONS (METRIC).pdf

《DLA MIL-DTL-83538 13 A-2008 CONNECTORS AND ACCESSORIES ELECTRICAL CIRCULAR UMBILICAL TEST PLUG REMOVABLE CRIMP CONTACTS PINS FOR MIL-STD-1760 APPLICATIONS (METRIC).pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-83538 13 A-2008 CONNECTORS AND ACCESSORIES ELECTRICAL CIRCULAR UMBILICAL TEST PLUG REMOVABLE CRIMP CONTACTS PINS FOR MIL-STD-1760 APPLICATIONS (METRIC).pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 METRICMIL-DTL-83538/13A 2 June 2008 SUPERSEDING MIL-DTL-83538/13 13 May 2005 DETAIL SPECIFICATION SHEET CONNECTORS AND ACCESSORIES, ELECTRICAL, CIRCULAR, UMBILICAL, TEST PLUG, REMOVABLE CRIMP CONTACTS, PINS, FOR MIL-STD-1760 APPLICATIONS (METRIC) This specification is approved for use by all Depart

2、ments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83538. FIGURE 1. Test plug. AMSC N/A FSC 5935 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

3、HS-,-,-MIL-DTL-83538/13A 2mm Inches 0.10 0.004 1.00 0.044 4.57 0.180 6.00 0.236 35.26 1.388 35.36 1.392 52.83 2.080 53.34 2.100 NOTES: 1. Dimensions are in millimeters. 2. Inch equivalents are given for information only. FIGURE 1. Test plug - Continued. REQUIREMENTS: Dimensions and configurations: S

4、ee figure 1. This connector mates with MIL-DTL-83538/4. Insert arrangement shall be in accordance with MIL-STD-1560 (25-20). Part or Identifying Number (PIN) example: M83538/13-1. QUALIFICATION: This test plug shall be in accordance with the qualification requirements of MIL-DTL-83538. The following

5、 details and exceptions shall apply: Group A: Visual and mechanical examination (100% inspection). Group B: Not applicable. Qualification and group C: Two MIL-DTL-83538/13 test samples are required for stand alone qualification. However, if the manufacturer is in the process of qualifying MIL-DTL-83

6、538/4 concurrently with the test plug, then one test sample shall be required for qualification. Testing shall be performed in the following sequence: Visual and mechanical examination. Insulation resistance and dielectric withstanding voltage. Manufacturers that are qualifying this test plug as a s

7、tand alone accessory shall conduct insulation resistance and dielectric withstanding voltage in accordance with the requirements of MIL-DTL-83538. Manufacturers that are in the process of qualifying MIL-DTL-83538/4 connectors concurrently with MIL-DTL-83538/13 are not required to perform these two t

8、ests separately, however, these manufacturers shall certify that the mating end of MIL-DTL-83538/13 is identical to the mating side of the MIL-DTL-83538/3 buffer plug which mates with MIL-DTL-83538/4. For group C, visual and mechanical, insulation resistance, dielectric withstanding voltage and post

9、 test examination shall be conducted. Post test examination. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83538/13A 3Changes from the previous issue: Marginal notations are not used in this revision to identify changes with respect to the

10、previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-83538, this document references the following: MIL-DTL-83538/3 MIL-DTL-83538/4 MIL-STD-1560 MIL-STD-1760 CONCLUDING MATERIAL Custodians: Preparing activity: Army CR DLA CC Navy AS Air Force 85 DLA CC Review

11、 activities: Army AR, MI (Project 59352007-050) Navy EC, MC, OS Air Force 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change. You should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-