DLA MIL-DTL-20633 D-2000 SIGNS AND MARKER ALUMINUM MINED AREA MARKING《雷区铝标记及标号器》.pdf

《DLA MIL-DTL-20633 D-2000 SIGNS AND MARKER ALUMINUM MINED AREA MARKING《雷区铝标记及标号器》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-20633 D-2000 SIGNS AND MARKER ALUMINUM MINED AREA MARKING《雷区铝标记及标号器》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、POT MEASUREMENT SENSITIVE1 MIL-DTL-20633D 14 January 2000 SUPERSEDING 16 February 1989 MIL-S-2063 3 C DETAIL SPECIFICATION SIGNS AND MARKER, ALUMINUM; MINED AREA MARKING This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This deta

2、il specification covers safe-lane and mined-area marking signs and a mine marker. 1.2 Classification The signs and markers should be of the following classes as specified (see 6.2(b). Class D - Safe-lane sign Class E - Mine marker Class F - Mined area sign 2. APPLICABLE DOCUMENTS 2.1 General. The do

3、cuments listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents in other sections of the specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, d

4、ocument users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be used in improving this document should

5、 be addressed to Defense Supply Center Richmond (DSCR), ATTN: DSCR-VBD, 8000 Jefferson Davis Highway, Richmond, VA 23297-56 1 O by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC NIA FSC 9905 DISTRIBUTION STATEMENT A. Ap

6、proved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-20633D 2.2 Government documents. 2.2.1 Government documents, drawings, and publications The following other Government documents, drawing, a

7、nd publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation (see 6.2(c). DRAWINGS U.S. ARMY TANK AUTOMOTIVE COMMAND 132 1 1E78 1 O - Sign, Mined Area Marking 1321 1E7811 - Sign Safe Lane Marking 1321 1E7812 -

8、 Marker, Land Mine (Copies of drawings are available from the U.S. Army Tank Automotive Command, ATTN: AMSTA-TR-E/EDS, Engineering Business Group MS#270, Warren, MI 48397-5000.) 2.3 Non-Government Publications The following documents form a part of this document to the extent specified herein. Unles

9、s otherwise specified, the issues of thdocuments which are DoD adopted are those listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in theDoDISS are the issues of the documents cited in the solicitation. AMERICAN NATIONAL STAND

10、ARDS INSTITUTE (ANSI) ANSUASQC Z 1.4- 1994 Sampling Procedures and Tables for Inspection by Attributes (DoD adopted) (Applications for copies should lx sent to: American National Standards Institute, 11 West 42nd Street, New York, NY 10036.) 2.4 Order of precedence. In the event of a conflict betwee

11、n the text of this document and the references cited herein (except for related associated specifications or specification sheets), the text of the document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.

12、3. REQUIREMENTS 3.1 First article. When specified (see 6.2(d), a sample shall be subjected to first article inspection in accordance with 4.2. 3.2 Quality Conformance Items shall meet the requirements of section 4.3. 3.3 Packaging. Items shall meet the requirements of section 4.4. 2 Provided by IHSN

13、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-20633D 3.4 Materials and components. Materials and components shall be as specified on the drawings referenced herein. When substitute components are proposed, the contractor shall submit to the responsible age

14、ncy a listing of all substitute components, samples of the components, and supporting data which proves the functional equivalence and design compatibility of the items. Approval of the submitted listing authorizes construction of the first article. 3.5 Construction. Construction shall conform in al

15、l respects to the drawings listed in section 2 and as specified herein. 4 VERIFICATION 4.1 Classification of inspections The inspection requirements specified herein are classified as follows: a. First article inspection (see 4.2) b. Quality Conformance inspection (ce 4.3) c. Inspection of packaging

16、 (see 4.4) 4.2 First article inspection When specified (see 6.2(e), a random sample shall be subject to first article inspection. The contractor shall furnish to the Government one or more safe-lane and mined-area marking signs and mine markers, as specified by the contract. Unless otherwise specifi

17、ed (see 6.2(e), all examination and test shall be conducted by the contractorand subjected to surveillance and approval by the Government. The signs and markers shall be examined for the characteristics in table I. Failure of first article signs and markers to meet examination criteria of table I sh

18、all be cause for rejection of the first article signs and markers. Any failure shall be cause for the Government to reject any production signs and markers until the contractor has provided acceptable evidence that the defects have been eliminated. Table I. Examination characteristics I Defects I Co

19、mponents missing or not assembled as specified. Dimensions not as specified. Materials not as specified. Workmanship not as specified. 4.3 Quality conformance inspection Samples shall be examined for the defects listed in table I. Sampling for examination shall be in accordance with ANSUASQC Z1.4. L

20、ot size shall be as specified (see 6.2(f). The unit of product is one safe-lane sign, one mined-area sign, and one mine marker. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-20633D 4.4 Inspection of packaging. The fully packaged end items

21、 shall be examined for compliance in accordance with section 5.1. Sampling shall be in accordance with ANSUASQC 21.4. The unit of product shall be a completed pack prepared for shipment. Thelot size will be specified by the contracting officer. 5. PACKAGING 5.1 Packaging. For acquisition purposes, t

22、he packaging requirements shall be as specified in the contract or order (see 6.2(g). When actual packaging of material is to be performed byDoD personnel, these personnel need to contact the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are mai

23、ntained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the Military Departments System Command. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products,

24、or by contacting the responsible packaging activity. 6. NOTES 6.1 Intended use. The class D sign is intended for marking a safe lane through a mined area. The class E mine marker is intended for marking the location of a detected mine until removal is accomplished. The class F sign is intended for m

25、arking mined areas. 6.2 Acquisition requirements Acquisition documents must specify the following: a. Title, number, and date of this document b. Class of sign or marker required (see 1.2) c. Issue of DoDISS to be cited in the solicitation, and if required, the specific issue of d. First article, if

26、 required (see 3.1) e. First article examination responsibility, if different (see 4.2) f. Quality conformance lot size, specify requirements (see 4.3) g. Packaging requirements (see 5.1) individual documents referenced (see 2.2.1) 6.3 Part identification number (PIN) The PIN to be used for signs an

27、d markers acquired to this specification are created as follows: - M 20633- Prefix for military Specification number specification - X Class 6.4 Subject term (key word) listing Safe-lane 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-20633D Custodians: Air Force - 99 Army - CR4 Preparing activity: DLA - GS (Project 9905-0349) Reviewers: Air Force - 84 Army - GL, MI 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-