DLA DSCC-DWG-93035 REV B-2004 CONNECTOR ACCESSORIES ELECTRICAL BACKSHELL ENVIRONMENTAL 90 DEG INDIVIDUAL AND OR OVERALL SHIELD TERMINATION (FOR MIL-DTL-38999 SERIES III AND IV CON.pdf

《DLA DSCC-DWG-93035 REV B-2004 CONNECTOR ACCESSORIES ELECTRICAL BACKSHELL ENVIRONMENTAL 90 DEG INDIVIDUAL AND OR OVERALL SHIELD TERMINATION (FOR MIL-DTL-38999 SERIES III AND IV CON.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-93035 REV B-2004 CONNECTOR ACCESSORIES ELECTRICAL BACKSHELL ENVIRONMENTAL 90 DEG INDIVIDUAL AND OR OVERALL SHIELD TERMINATION (FOR MIL-DTL-38999 SERIES III AND IV CON.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、NOTICE OF REVISION (NOR) This revision described below has been authorized for the document listed. 1. DATE (YYMMDD) 04-05-07 DSCC-VAI b. ADDRESS (Street, City, State, Zip Code) 4. ORIGINATOR Defense Supply Center Columbus 3990 East Broad Street Columbus, Ohio 43216-5000 a. TYPED NAME (First, Middle

2、 Initial. Last) Jeffery Tunstall Richard L. Taylor 03723 d. TITLE e. SIGNATURE CHIEF,INTERCONNECION Richard L. Taylor DEVICES 15a. ACTIVITY ACCOMPLISHING REVISION b. REVISION COMPLETED (Signature) DSCC-VAI Jeffery Tunstall 7. CAGE CODE I 03723 f. DATE SIGNED (04-05-07) c. DATE SIGNED (04-05-07) 9. T

3、ITLE OF DOCUMENT CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, ENVIRONMENTAL, 90” INDIVIDUAL AND/OR OVERALL AND IV CONNECTORS). SHIELD TERMINATION, (FOR MIL-DTL-38999 SERIES III 1 IO. REVISION LETTER Form Approved 0188 OMB NO. 0704- 3. DODAAC 6. NOR NO. 5935-R033-03 8. DOCUMENT NO 93035 , ECPNO. NIA

4、 LltS ALL 13. DESCRIPTION OF REVISION Page 3, Figure 1: Add Max cable range” column to accessory shell size table, as shown to the left. Page 5, Vendor CAGE number table Delete: “390HA005” and substitute: “390HB005”. (1) Existing document supplemented by the NOR may be used in manufacture. (2) Revis

5、ed document must be received before manufacturer may incorporate this change. a. (X one) I I (3) Custodian of master document shall make above revision and furnish revised document. b. ACTIVITY AUTHORIZED TO APPROVE CHANGE FOR GOVERNMENT I c. TYPED NAME (First, Middle Initial. Last) Provided by IHSN

6、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-LTR A I Correcting address list of sources. I I DESCRIPTION DATE APPROVED Robert Heber Update format. 16 July 02 Correcting references. REV STATUS CHECKED BY Abdo Abdouni APPROVEDBY Robert Heber I PMIC NIA TITLE CONNEC

7、TOR ACCESSORIESl ELECTRICAL, BACKS HELL, ENVIRONMENTAL, 90“ INDIVIDUAL AND/OR OVERALL SHIELD TERMINATION, CATEGORY CONNECTORS) 2A (FOR MIL-DTL-38999 SERIES 111 AND IV Original date of drawing SIZE A November 14,1994 93035 CAGE CODE DWG. NO. 03723 PREPARED BY Jeffery Tunctall DEFENSE SUPPLY CENTER, C

8、OLUMBUS 1 COLUMBUS, OHIO 4321 6-5000 1 OF 5 - I REV A I PAGE SMSC NIA 5935-E675 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CONFIGURATION CEE REQMT1 pHxp OFT IONAL 7 O-RING- I OPTIONAL SHIELD TERMINATION METHOD OPTIONAL Il DESIGN OPTIONAL STYLE A

9、 FIGURE I I H i STYLE B . Dimensions and confiquration. STYLE C CAGE CODE DWG NO. 03723 93035 A DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Clamp size Cable accommodation range B max K max N

10、 max Min Max NOTES: 1. Dimensions are in millimeters. Inch-pound equivalents are in parentheses. 2. Dimensions apply after plating. 3. The U.S. Government preferred system of measurements is the metric SI system. However, this item was originally using inch-pound units of measurement, in the event o

11、f conflict between the metric and inch-pound units, the inch-pound units shall take precedence. o1 02 03 04 05 06 07 08 o9 10 11 FIGURE 1. Dimensions and configuration - Continued. 3.99 (.157) 5.33 (.210) 19.30 (.760) 21.4 (.84) 16.0 (.63) 4.75 (.187) 7.92 (.312) 19.30 (.760) 23.0 (.91) 19.2 (.76) 7

12、.14 (.281) 11.13 (.438) 19.30 (.760) 27.8 (1.09) 23.9 (.94) 9.83 (.387) 14.27 (562) 19.30 (.760) 30.01 (1.19) 27.1 (1.07) 10.80 (.425) 15.88 (.625) 19.30 (.760) 32.5 (1.28) 30.3 (1.19) 14.61 (575) 19.05 (.750) 19.30 (.760) 38.1 (1.50) 35.1 (1.38) 17.78 (.700) 23.83 (.938) 27.30 (1.073) 43.7 (1.72) 3

13、9.0 (1 54) 22.53 (.887) 31.75 (1.250) 33.60 (1.323) 52.4 (2.06) 46.9 (1.85) 30.48 (1.200) 34.93 (1.375) 33.60 (1.323) 58.7 (2.31) 57.3 (2.26) 33.65 (1.325) 41.28 (1.625) 39.93 (1.572) 69.1 (2.72) 63.8 (2.51) , 40.01(1.575) , 47.60 (1.875) , 39.93 (1.567) , 75.4 (2.97) , 70.0 (2.76) CAGE CODE DWG NO.

14、 03723 93035 A DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 4321 6-5000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-REQUIREMENTS: Shall be in accordance with MIL-C-85049, category 2A. Backshell shall be capable of terminating individual and/or ov

15、erall shields or double overall shields and provide an environmental seal. Design and construction: See figure 1. Interface dimensions shall confirm to MIL-C-85049 accessory intermateability data for MIL-DTL-38999, series III and IV connectors. Material: Accessory components: Aluminum alloy shall be

16、 in accordance with MIL-C-85049. O-ring and grommet: Shall be in accordance with MlL-C-85049. Finish: N and W shall be in accordance with MIL-C-85049. Finish N is for space application only. Part or Identifying Number (PIN): The PIN shall be in accordance with the following: Example: - C - O Drawing

17、 number Finish Shell size (see figure 1) Strain relief style Cable accommodation range Marking: Marking shall be in accordance with MlL-C-85049 except the PIN shall be as stated above. QUALIFICATION: Qualification inspection: Qualification inspection for the adapter specified herein shall not be req

18、uired. Qualification conformance inspection: Shall be in accordance with MIL-C-85049. Inspection of packaging: Shall be in accordance with MIL-C-85049. Methods of inspection: Shall be in accordance with MIL-C-85049. CAGE CODE DWG NO. 03723 93035 A DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5

19、000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DSCC drawing Vendor CAGE number 93035* 03723 REV A A I I l I - I/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. 93035 PAGE 5 Vendor CAGE num

20、ber Vendor name and address 31461 06324 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 4321 6-5000 Electro Adapter, Incorporated 20640 Nordhoff Street Chatcworth, CA 91 31 1 Glenair, Incorporated 121 1 Air Way Glendale, CA 91201-2497 I CAGECODE I DWGNo. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-