DLA DSCC-DWG-89034 REV B-2001 CONNECTOR ELECTRICAL RECEPTACLE RADIO FREQUENCY SERIES TNC FLANGE MOUNTED CRES BODY SOLDER POCKET STANDARD SCREWS《系列TNC法兰安装件射频插座连接器 新月形 标准螺母》.pdf

《DLA DSCC-DWG-89034 REV B-2001 CONNECTOR ELECTRICAL RECEPTACLE RADIO FREQUENCY SERIES TNC FLANGE MOUNTED CRES BODY SOLDER POCKET STANDARD SCREWS《系列TNC法兰安装件射频插座连接器 新月形 标准螺母》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-89034 REV B-2001 CONNECTOR ELECTRICAL RECEPTACLE RADIO FREQUENCY SERIES TNC FLANGE MOUNTED CRES BODY SOLDER POCKET STANDARD SCREWS《系列TNC法兰安装件射频插座连接器 新月形 标准螺母》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、REVISIONSLTR DESCRIPTION DATE APPROVEDA Add source 95077. 2 Aug 1993 Randy LarsonB PIN and source update. 3 August 2001 Robert HeberPrepared in accordance with MIL-STD-100.REVPAGEREVBBBBREV STATUSOF PAGES PAGE 1234PREPARED BYPMIC N/ARon GaryDEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OHIO 43216-5000CHE

2、CKED BY TITLEC. W. KoellerAPPROVED BYRichard MarbaisCONNECTOR, ELECTRICAL, RECEPTACLE, RADIOFREQUENCY, SERIES TNC, FLANGE MOUNTED,CRES BODY, SOLDER POCKET, STANDARD SCREWSSIZE CAGE CODE037Z3DWG. NO. 89034Original date ofdrawing20 November 1989AREV B PAGE 1 OF 4AMSC N/A 5935-E641-11DISTRIBUTION STATE

3、MENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZECAGE CODE DWG NO.037Z3 89034DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OH 43216-5000AREVBPAGE2Inches mm Inches mm.060 1.52 .35 8.9.080 2.

4、03 .496 12.60.100 2.54 .504 12.80.120 3.04 .563 14.30.125 3.18 .68 17.3.130 3.30 .687 17.45.246 6.24 .70 17.8.254 6.45 1.06 26.9.34 8.6NOTES:1. Dimensions are in inches.2. Metric equivalents are given for general information only.3. There shall be a solder barrier in the socket between the pin entry

5、 and the solder pocket to prevent solder wicking.4. All undimensioned pictorial configurations are for reference purposes only.5. Interface dimensions shall be in accordance with MIL-STD-348, series TNC, socket contact.FIGURE 1. Flange mount TNC.Provided by IHSNot for ResaleNo reproduction or networ

6、king permitted without license from IHS-,-,-SIZECAGE CODE DWG NO.037Z3 89034DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OH 43216-5000AREVBPAGE3ENGINEERING DATA:Nominal impedance: 50 ohms.Frequency range: 500 MHz to 11 GHz.Voltage rating: 500 volts rms sea level, minimum.125 volts rms at 70,000 feet, mi

7、nimum.Operating temperature: -65C to +165C.REQUIREMENTS: (Requirements of DSCC drawing 84148 are applicable).Dimensions and configuration: See figure 1 and MIL-STD-348.Force to engage and disengage: 2 inch-pounds maximum axial torque (.225 Nm).Longitudinal force: Not applicable.Coupling proof torque

8、: Not applicable.Hermetic seal: Not applicable.Leakage (pressurized connectors): Not applicable.Center contact retention: 6 pounds minimum axial force (26.69 N).Radial torque: Not applicable.Voltage standing wave ratio (VSWR): Not applicable.Moisture resistance: Method 106, MIL-STD-202, no measureme

9、nts at high humidity. Insulation resistance shall be at least 200megohms minimum within 5 minutes after removal from humidity.Contact resistance (in milliohms maximum):AfterInitial environmentalCenter contact: 1.5 1.5Outer contact: 2.0 N/AInsulation resistance: 5000 megohms, minimum, when tested in

10、accordance with MIL-STD-202, method 302, test condition B.Dielectric withstanding voltage: 1,500 V rms minimum, in accordance with MIL-STD-202, method 301.Vibration, high frequency: MIL-STD-202, test condition B of method 204.Corrosion: MIL-STD-202, test condition B, method 101.Corona level: 375 V r

11、ms, at 70,000 feet (21.336 km).Shock (specified pulse): Method 213, test condition I of MIL-STD-202.Thermal shock: MIL-STD-202, test condition C of method 107, except that the test high temperature condition shall be +200C.RF high potential withstanding voltage: 1,000 V rms, minimum.Frequency: 5 MHz

12、.Leakage current: Not applicable.Cable retention force: Not applicable.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZECAGE CODE DWG NO.037Z3 89034DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OH 43216-5000AREVBPAGE4Solderability: MIL-STD-202, method

13、208.Coupling mechanism retention force: Not applicable.RF leakage: Not applicable.RF insertion loss: .Not applicable.NOTE: These connectors are for use in radio frequency applications only.Part or Identifying Number (PIN): 89034TSP.Approved sources of supply. Approved sources of supply are listed he

14、rein. Additional sources will be added as theybecome available. The vendors listed on the requirements drawing have agreed to this drawing and a certificate ofcompliance has been submitted to DSCC-VAI.DSCC drawingPIN 1/Vendor CAGEnumberVendor referencePIN 89034TSP 00795950771213000K181-001SF4060-602

15、01/ Parts must be purchased to this DSCC PIN to assure that allperformance requirements and tests are met.Vendor CAGE Vendor namenumber and address00795 Delta Electronics416 Cabot StreetBeverly, MA 0191595077 Solitron/Vector Microwave Products3301 Electronics WayWest Palm Beach, FL 33407Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-