DLA DSCC-DWG-86120 REV G-2006 CONNECTOR PLUG ELECTRICAL SERIES SSMA PIN CONTACT RIGHT ANGLE FOR FLEXIBLE CABLE《针触式SSMA系列的柔性电缆的电器插头连接器》.pdf

《DLA DSCC-DWG-86120 REV G-2006 CONNECTOR PLUG ELECTRICAL SERIES SSMA PIN CONTACT RIGHT ANGLE FOR FLEXIBLE CABLE《针触式SSMA系列的柔性电缆的电器插头连接器》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-86120 REV G-2006 CONNECTOR PLUG ELECTRICAL SERIES SSMA PIN CONTACT RIGHT ANGLE FOR FLEXIBLE CABLE《针触式SSMA系列的柔性电缆的电器插头连接器》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、REVISIONS LTR DESCRIPTION DATE APPROVED A Add source and modify insertion loss. 7 Jun 1990 R. Marbais B Add CAGE 34078 as source. 4 Jun 1991 Randy Larson C Add CAGE 95077 as source. 20 Mar 1995 Randy Larson D PIN and source update 16 Nov 2001 Robert M. Heber E Incorporate NOR 17 Jan 2003 Robert M. H

2、eber F Incorporate NOR 24 Mar 2003 Richard L. Taylor G Update vendor part number for CAGE 95077 21 April 2006 Richard L. Taylor Requirements of DSCC drawing 84148 are applicable. Prepared in accordance with ASME-Y14.100. REV PAGE REV G G G G G REV STATUS OF PAGES PAGE 1 2 3 4 5 PREPARED BY PMIC N/A

3、Ron Gary DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 CHECKED BY TITLE Jeffery Bohannon APPROVED BY Richard Marbais CONNECTOR, PLUG, ELECTRICAL, SERIES SSMA, PIN CONTACT, RIGHT ANGLE, FOR FLEXIBLE CABLE SIZE CAGE CODE 037Z3 DWG. NO. 86120 Original date of drawing 21 January 1987 A REV G

4、 PAGE 1 OF 5 AMSC N/A 5935-E787-000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for Information only. 3. Wrench flats are to accommodate standard wrench opening in accordance wit

5、h FED-STD-H28, appendix 10. 4. All undimensioned pictorial configurations are for reference purposes only. 5. Dimensions .900 (22.86 mm) defines the maximum overall length of the connector when assembled to the cable. 6. Assembled using crimp tool M22520/5-01, die M22520/5-03, closure A. 7. Coupling

6、 nut is to be passivated corrosion resisting steel in accordance with MIL-PRF-39012. 8 Unless otherwise specified, tolerances are .005 (0.13 mm). FIGURE 1. General configuration. SIZE CAGE CODE DWG NO. 037Z3 86120 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVG PAGE2 Provided by IHSNo

7、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-ENGINEERING DATA: Nominal impedance: 50 ohms. Frequency range: 0 - 26 GHz. (Connector performance only. Frequency range dependent on cable used.) Voltage rating: 250 V rms at sea level. 60 V rms at 70,000 feet. Operatin

8、g temperature: -65C to +165C. REQUIREMENTS: Requirements of drawing 84148 applicable. Dimensions and configuration: See figure 1. Force to engage and disengage: Longitudinal force: Not applicable. Torque: 2 inch-pounds, maximum. Coupling proof torque: 7 inch-pounds, minimum. Hermetic seal: Not appli

9、cable. Leakage (pressurized connectors): Not applicable. Center contact retention: 4 pounds, minimum. Radial torque: Not applicable. Voltage standing wave ratio (VSWR): 1.10 + .015F (F in GHz) dB, maximum. (Not applicable to RG179.) Moisture resistance: Method 106, MIL-STD-202, no measurements at hi

10、gh humidity. Insulation resistance shall be at least 200 megohms within 5 minutes after removal from humidity. Contact resistance (in milliohms, maximum): Initial After environmentCenter contact: 4.0 4.0 Outer contact: 2.0 Not applicable Outer conductor to body: 0.5 Not applicable Dielectric withsta

11、nding voltage at sea level: 750 V rms, minimum. Vibration, high frequency: Method 204, test condition D, MIL-STD-202. Corona level: Altitude: 70,000 feet. 190 V rms, minimum. Shock (specified pulse): Method 213, test condition I, MIL-STD-202. Thermal shock: Method 107, test condition B, MIL-STD-202,

12、 except test high temperature shall be +85C. SIZE CAGE CODE DWG NO. 037Z3 86120 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVG PAGE3 Barometric pressure (reduced): Not applicable.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-RF high

13、 potential withstanding voltage: 500 V rms, minimum. Frequency: 5 MHz. Leakage current: Not applicable. Cable retention force: 20 pounds, minimum. Torque: 16 inch-ounces, minimum. Coupling mechanism retention force: 80 pounds, minimum. RF leakage: -90 + F (F in GHz)dB, minimum. RF insertion loss: .0

14、6 F, GHz dB, maximum. Note: These parts are for use in general radio frequency applications. Part or Identifying Number (PIN): See table I. TABLE I. Connector to cable reference. PIN Cable accommodation 86120ZSG M17/113-RG316, M17/173-00001 M17/119-RG174, M17/172-00001, M17/94-RG179 Approved sources

15、 of supply are listed herein. Additional sources will be added as they become available. The vendors listed on the requirements drawing have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. DSCC drawing PIN 1/ Vendor CAGE number Vendor reference PIN 86120ZSG 007

16、79 34078 95077 0145517-1 SSM-3188-56-001-02 SF2713-6031 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. SIZE CAGE CODE DWG NO. 037Z3 86120 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVG PAGE4 Provided by IHSNot for ResaleNo r

17、eproduction or networking permitted without license from IHS-,-,-Vendor CAGE Vendor name number and address 00779 TYCO Electronics P.O. Box 3608 Harrisburg, PA 17105 34078 Midwest Microwave 6564 South State Road Saline, MI 48176 95077 S/V Microwave, Inc. 2400 Centrepark West Dr. Suite 100 SIZE CAGE CODE DWG NO. 037Z3 86120 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVG PAGE5 West Palm Beach, FL 33409 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-