DLA DSCC-DWG-86031 REV J-2005 RELAY SOLID STATE OPTICALLY ISOLATED 10 AMPERE LOAD AT 250 V AC DC INPUT CONTROL《250伏10安培直流输入控制的光隔离固态继电器》.pdf

《DLA DSCC-DWG-86031 REV J-2005 RELAY SOLID STATE OPTICALLY ISOLATED 10 AMPERE LOAD AT 250 V AC DC INPUT CONTROL《250伏10安培直流输入控制的光隔离固态继电器》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-86031 REV J-2005 RELAY SOLID STATE OPTICALLY ISOLATED 10 AMPERE LOAD AT 250 V AC DC INPUT CONTROL《250伏10安培直流输入控制的光隔离固态继电器》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Changed manufacturers eligibility. 24 Aug 87 D. Moore B Clarify parameters. 24 Aug 88 D. Moore C Changed several electrical requirements. Corrected top view dimension on figure 1. Editorial changes throughout. 4 Dec 89 D. Moore D Changed dimensions on figur

2、e 1. Added note to correctly show anti-rotation boss. Editorial changes throughout. 12 Sep 91 D. Moore E Changes in accordance with NOR 5945-R003-93. 10 Mar 93 D. Moore F Changed CAGE 63745 to CAGE 16170. Updated to current requirements of MIL-R-28750C. Changed paragraphs 3.5.1, 3.5.2, 3.6.6, 3.8.1,

3、 3.8.2, and 3.8.3. Changed figures 2 and 4. Editorial changes throughout. 9 Jun 95 D. Moore G Changes in accordance with NOR 5945-R002-98. 15 Apr 98 D. Moore H Validation and update. 25 Jul 03 K. Cottongim J Changed CAGE 58614 to CAGE 18741. 7 Dec 05 W. Sindelar Prepared in accordance with ASME Y14.

4、100 Selected item drawing REV PAGE REV PAGE REV REV STATUS OF PAGES PAGES PMIC N/A PREPARED BY Tony J. Westphal CHECKED BYDavid E. Moore APPROVED BYDavid E. Moore SIZE A CODE IDENT. NO.Original date of drawing 14 April 1986 REV J CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY AMSC

5、N/A DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHSDEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 H H H H H H H H J 1 2 3 4 5 6 7 8 9 DESIGN ACTIVITY DEFENSE ELECT

6、RONICS SUPPLY CENTER DAYTON, OH 45444-5000 TITLE RELAY, SOLID STATE, OPTICALLY ISOLATED, 10 AMPERE LOAD AT 250 V AC, DC INPUT CONTROL 14933 DWG NO. 86031 PAGE 1 OF 9 5945-E126 -,-,-1. SCOPE 1.1 Scope. This drawing describes the requirements for nonhermetically sealed solid state relays supplied to t

7、he Y level screen requirements of MIL-PRF-28750. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 86031 -001| | | | Drawing Dash number number 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, st

8、andards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (s

9、ee 6.3). SPECIFICATIONS DEPARTMENT OF DEFENSE MIL-PRF-28750 - Relays, Solid State, General Specification for. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-202 - Test Method Standard Electronic and Electrical Component Parts. MIL-STD-883 - Test Method Standard Microcircuits. (Unless otherwise indicated, c

10、opies of federal and military specifications, standards, and handbooks are available from the Document Automation and Production Service, Building 4D (DPM-DODSSP), 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this document

11、and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance wit

12、h MIL-PRF-28750, and as specified herein. 3.2 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-28750, and herein (see figure 1). DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OH A 14933 86031 REV H PAGE 2 Provided by IH

13、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.3 Input characteristics. 3.3.1 Control voltage range. Control voltage range shall be 3.8 V dc minimum to 32 V dc maximum. Rated control voltage shall be 5 V dc. 3.3.2 Turn-on voltage. Turn-on voltage shall be 3.8 V

14、 dc minimum. 3.3.3 Turn-off voltage. Turn-off voltage shall be 1.0 V dc maximum. 3.3.4 Input current. Input current shall be 16 milliamperes maximum (see figure 2). 3.3.5 Reverse polarity. Applicable. 3.4 Output characteristics. 3.4.1 Output current. Output current shall be .15 ampere minimum to 10

15、amperes maximum (see figure 3). 3.4.2 Output voltage range. Output voltage range shall be 25 V ac minimum to 250 V ac maximum. Rated output voltage shall be 250 V ac. 3.4.3 Output frequency range. Output frequency range shall be 45 Hz minimum to 440 Hz maximum. Rated output frequency shall be 400 Hz

16、. 3.4.4 Surge current. See figure 4. 3.4.5 Voltage drop at maximum current. Voltage drop at maximum current shall be 1.5 V rms maximum (see figure 5). 3.4.6 Output leakage current. Output leakage current shall be 9 mA maximum at 250 V ac, 400 Hz (+85C). 3.4.7 Power dissipation. Power dissipation sha

17、ll be 1.5 watts/ampere maximum (+25C). 3.4.8 Transient voltage. The applied voltage shall be 460 V peak maximum (T 20 ms). 3.4.9 Turn-on time. Turn-on time shall be one-half cycle (400 Hz) maximum. 3.4.10 Turn-off time. Turn-off time shall be one cycle (400 Hz) maximum. 3.4.11 Zero voltage turn-on p

18、oint. Zero voltage turn-on point shall be 15 V peak maximum (-55C to +85C). 3.4.12 Exponential rate of voltage rise (dv/dt). Exponential rate of voltage rise (dv/dt) shall be 200 V/s. 3.5 Electrical characteristics. 3.5.1 Insulation resistance. Insulation resistance shall be in accordance with MIL-P

19、RF-28750, except the resistance shall be 100 megohms minimum at 500 V dc (input-to-output only). 3.5.2 Dielectric withstanding voltage. The dielectric withstanding voltage, from all pins-to-case, shall be 1,500 V ac at 60 Hz minimum, in accordance with MIL-PRF-28750. 3.5.3 Isolation. Isolation shall

20、 be 15 pF maximum (input to output). 3.5.4 Overload. Applicable (see figure 4). 3.5.5 Electromagnetic interference. Not applicable. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OH A 14933 86031 REV H PAGE 3 Provided by IHSNot for ResaleNo reproduction or networking permitted

21、 without license from IHS-,-,-3.5.6 Fusing I2T (1 ms). Fusing I2T (1 ms) shall be 150 A2s maximum. 3.5.7 Load power factor. Load power factor shall be 0.2 minimum. 3.5.8 Minimum current rating. Not applicable. 3.5.9 DC offset voltage. Not applicable. 3.5.10 Waveform distortion. Not applicable. 3.6 E

22、nvironmental data. 3.6.1 Operating temperature range. Operating temperature range shall be -55C to +95C. 3.6.2 Storage temperature range. Storage temperature range shall be -55C to +110C. 3.6.3 Shock. Shock shall be in accordance with MIL-STD-202, method 213, test condition I. 3.6.4 Vibration. Vibra

23、tion shall be in accordance with MIL-STD-202, method 204, test condition G, except the frequency range shall be 78 Hz to 2,000 Hz. 3.6.5 Acceleration. Acceleration shall be in accordance with MIL-STD-883, method 2001, 100 gs, Y1 axis only. 3.6.6 Thermal shock. Not applicable. 3.6.7 Resistance to sol

24、vents. Not applicable. 3.6.8 Moisture resistance. Applicable. 3.7 Physical. Physical requirements shall be as specified herein. 3.7.1 Weight. Weight shall be 85 grams maximum (3.0 ounces). 3.7.2 Dimensions and configuration. See figure 1. 3.7.3 Seal. Not applicable. 3.8 Thermal ratings. 3.8.1 Output

25、 switch junction temperature. Output switch junction temperature, (TJ), shall be +150C maximum. 3.8.2 Thermal resistance, junction to ambient. Thermal resistance, junction to ambient, (JA), shall be 15.5C/W maximum. 3.8.3 Thermal resistance, junction to heat sink. Thermal resistance, junction to hea

26、t sink, (JS), shall be 2.5C/W maximum (includes CS). 3.9 Marking. Marking shall be in accordance with MIL-PRF-28750, except the relay shall be marked with the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, and date lot codes. The M28750/X-X

27、XXY PIN shall not be used. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OH A 14933 86031 REV H PAGE 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Inches mm .015 .02 .05 .06 .11 .16 .30 .44 .50 .60 .75 .875 1.00 1.10 2.00

28、0.38 0.5 1.3 1.5 2.8 4.1 7.6 11.2 12.7 15.2 19.1 22.23 25.4 27.9 50.8 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm) for three place decimals and .01 (0.25 mm) for two place decimals. 4. C

29、ircuit diagram shown on part is terminal view. FIGURE 1. Dimensions and configuration. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OH A 14933 86031 REV H PAGE 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FIGURE 2. Typic

30、al input current versus input voltage. FIGURE 3. Thermal derating curves. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OH A 14933 86031 REV H PAGE 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTE: Output may lose blocki

31、ng capability during and after surge until TJfalls below maximum. FIGURE 4. Peak surge current versus surge current duration. FIGURE 5. Typical output voltage drop versus load current. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OH A 14933 86031 REV H PAGE 7 Provided by IHS

32、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.10 Waveform distortion. Not applicable. 3.11 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.12 Recycled, recovered, or en

33、vironmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.13 Workm

34、anship. The relay shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Product assurance program. The product assurance program specified in MIL-PRF-28750 is not applicable to this document. 4.2 Statistical process control. T

35、he statistical process control program specified in MIL-PRF-28750 is not applicable to this document. 4.3 Conformance inspection. 4.3.1 Inspection of product for delivery. Inspection of product for delivery shall consist of the group A inspections of MIL-PRF-28750 for the Y screening level. Group A

36、testing shall be performed on each inspection lot and manufacturers shall keep lot records for 3 years (minimum), monitor for compliance to the prescribed procedures, and records on lots are maintained for these relays. Components used internally to the relay shall not require hermetic packaging. Te

37、mperature range for screening tests shall be as specified in 3.6.1 herein. 4.3.2 Inspection of packaging. Inspection of packaging shall be in accordance with MIL-PRF-28750. 4.4 Methods of inspection. Methods of inspection shall be in accordance with MIL-PRF-28750. 5. PACKAGING 5.1 Packaging. For acq

38、uisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.3). When actual packaging of materiel is to be performed by DoD personnel, these personnel need to contact the responsible packaging activity to ascertain requisite packaging requirements. Packaging r

39、equirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the Military Departments System Command. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files

40、, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Notes. Only definitions of the notes specified in MIL-PRF-28750 will apply to this drawing. 6.2 Inte

41、nded use. Relays conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. This drawing is intended exclusively to prevent the proliferation of unnecessary du

42、plicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing on QPL-28750, this drawing will become inactive for new design. The QPL-28750 product shall be the preferred item for all applicat

43、ions. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OH A 14933 86031 REV H PAGE 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-6.3 Ordering data. The contract or purchase order should specify the following: a. Complete PIN

44、(see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. 6.4 Replaceability. Relays covered by this dra

45、wing will replace the same generic devices covered by contractor-prepared specifications or drawings. 6.5 Users of record. Coordination of this document for future revisions are coordinated only with the suggested sources of supply and the users of record of this document. Requests to be added as a

46、recorded user of this drawing should be in writing to: Defense Supply Center, Columbus, ATTN: DSCC/VAT, Post Office Box 3990, Columbus, OH 43216-5000 or by telephone (614) 692-0554 or DSN 850-0554. 6.6 Suggested sources of supply. Suggested sources of supply are listed herein. Additional sources wil

47、l be added as they become available. For assistance in the use of this drawing, contact Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43216-5000 or by telephone (614) 692-0554 or DSN 850-0554. DSCC drawing PIN Vendor similar designation or type number 1/ Vendor

48、CAGE Vendor name and address 86031-001 602-1Y 16170 Teledyne Microelectronic Technologies 12964 Panama Street Los Angeles, CA 90066-6534 Phone: (310) 822-8229 86031-001 PS12-1Y 18741 Tyco Electronics-Kilovac550 Linden Avenue Carpinteria, CA 93013 Phone: (805) 220-2023 1/ Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OH A 14933 86031 REV H PAGE 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-