DLA DSCC-DWG-85085 REV C-2005 RESISTOR VARIABLE NONWIRE-WOUND ADJUSTMENT TYPE 1 2 WATT TRIMMER《微调1 2瓦可调整型无线式可变电阻器》.pdf

《DLA DSCC-DWG-85085 REV C-2005 RESISTOR VARIABLE NONWIRE-WOUND ADJUSTMENT TYPE 1 2 WATT TRIMMER《微调1 2瓦可调整型无线式可变电阻器》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-85085 REV C-2005 RESISTOR VARIABLE NONWIRE-WOUND ADJUSTMENT TYPE 1 2 WATT TRIMMER《微调1 2瓦可调整型无线式可变电阻器》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Page 8 - Para. 6.4 add additional suggested sources of supply. Part number - 186P*;vendor - CTS; Vendor ID number 11236; Editorial changes throughout. 18 Apr 86 D. WITHROW B Remove vendor. Editorial changes throughout. 28 July 99 K. COTTONGIM C Terminal len

2、gth change. Editorial and procedural changes throughout 2 Feb 05 K. COTTONGIM Prepared in accordance with ASME Y14.100 Selected item drawing REV C C C C C C C REV STATUS OF PAGES PAGES 1 2 3 4 5 6 7 PMIC N/A PREPARED BY Allan R. Knox DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH CHECKED BY David W. W

3、ithrow APPROVED BY James Burkhart TITLE RESISTOR, VARIABLE, NONWIRE-WOUND, ADJUSTMENT TYPE, 1/2 WATT, TRIMMER SIZE A CODE IDENT. NO. 14933 DWG NO. 85085 Original date of drawing 18 November 85 REV C PAGE 1 OF 7 AMSC N/A 5905-E509 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFEN

4、SE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85085 REV C PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the

5、requirements for an trimmer. 1/2 watt, adjustment type, nonwire-wound, variable resistor. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 88085 - 01 Drawing number Dash number 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following sp

6、ecifications and standards form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-22097 - Resistor Variable, Nonwire-wound (Adjustment Type), G

7、eneral Specification For. DEPARTMENT OF DEFENSE STANDARD MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Ave

8、nue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a sp

9、ecific exemption has been obtained. 3. REQUIREMENTS 3.1 Item Requirements. The individual item requirements shall be as specified herein. 3.2 Interface and physical dimensions. The resistor shall meet the interface and physical dimensions as specified in MIL-PRF-22097 and herein (see figure 1). 3.3

10、Electrical characteristics. 3.3.1 Nominal resistance. The nominal resistance value shall be in accordance with table I. 3.3.2 Maximum rated working voltage. The maximum rated working voltage shall be in accordance with table I. 3.3.3 Power rating. Resistors shall have a power rating of 0.5 watt base

11、d on continuous full load operation at an ambient temperature of 70OC. For operation at temperature higher than 70OC, derate in accordance with figure 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO

12、SIZE A CODE IDENT NO. 14933 DWG NO. 85085 REV C PAGE 3 Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm 0.001 0.03 0.010 0.25 0.030 0.76 0.060 1.52 0.190 4.83 0.250 6.35 0.002 0.05 0.015 0.38 0.035 0.89 0.100 2.54 0.200 5.08 0.500 12.70 0.005 0.13 0.025 0.64 0.045 1.14 0.125 3.18 0.210 5.

13、33 0.750 19.05 NOTES: 1. All dimensions are in inches. 2. Metric equivalents are for information only. FIGURE 1. Dimensions and configuration. 2 1 3 0.210 + 0.035 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYT

14、ON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85085 REV C PAGE 4 TABLE I. Nominal resistance value and maximum working voltage. Dash number Nominal resistance value in ohms () Maximum working voltage 01 10 2.2 02 20 3.2 03 50 5.0 04 100 7.1 05 200 10.1 06 500 15.8 07 1,000 22.4 08 2,000 31.6 09 5,000

15、 50.0 10 10,000 70.7 11 20,000 100 12 25,000 112 13 50,000 158 14 0.10M 224 15 0.20M 300 16 0.25M 17 0.50M 300 18 1.00M 3.3.4 Resistance tolerance. The resistance tolerance be 10 percent. 3.3.5 End resistance. When measured as specified in 4.4, the end resistance shall be 2 ohms maximum. 3.3.6 Conta

16、ct resistance variation. When measured as specified in 4.4, the contact resistance variation shall be 1 percent/3 percent, or 1 ohm/3 ohms, whichever is greater (see 6.3). 3.3.7 Resistance temperature characteristic(RTC). When resistors are tested as specified in 4.4, the RTC shall be 100 ppm/OC and

17、 if the RTC is less than 100 ohms, 200 ppm/OC 3.3.8 Setability. When resistors are tested as specified in 4.4, the setability shall be 2 percent maximum. 3.3.9 Insulation resistance. When resistors are tested as specified in 4.4, the insulation resistance shall not be less than 1000 megohms. 3.3.10

18、Actual effective-electrical travel. When resistors are tested as specified in 4.4, the number of turns of the operating shaft necessary for the contact arm to traverse the resistance element shall be 10 turns minimum and 28 turns maximum. 3.4 Torque. 3.4.1 Operating torque. When resistors are tested

19、 as specified in 4.4, the torque required to move the contact arm shall be 5 inch-ounce maximum. 3.4.2 Clutch. When resistors are tested as specified in 4.4, the contact arm shall idle against the stop without electrical discontinuity or evidence of mechanical damage. The travel arm shall be capable

20、 of reversing direction. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85085 REV C PAGE 5 FIGURE 2. Derating curve. 3.5 Thermal shock. When resistors are tested as

21、specified in 4.4, the change in total resistance shall not exceed 2 percent. 3.6 Solderability. When resistors are tested as specified in 4.4, the dipped surface of the terminals shall be at least 95 percent covered with a new, smooth, continuous surface, free from pinholes. The remaining 5 percent

22、of the terminal surface shall show only pinholes, voids, or rough spots. These shall not be concentrated in one area. Bare base metal, and areas where the solder dip failed to cover the original coating are indicators of poor solderability and shall be cause for failure. In case of a dispute, the pe

23、rcent of coverage with pinholes or rough spots shall be determined by actual measurement of these areas compared to the total area. 3.7 Resistance to solvents. When resistors are tested as specified in 4.4, there shall be no evidence of mechanical damage. 3.8 Immersion. When resistors are tested as

24、specified in 4.5, no more than three bubbles shall be omitted. 3.9 Weight. The maximum weight shall be 0.00551 pounds (2.5 grams). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 1

25、4933 DWG NO. 85085 REV C PAGE 6 3.10 Marking. Resistors shall be marked with the PIN assigned herein (see 1.2) and the manufacturers Commercial and Government Entity (CAGE) code (or logo) in accordance with MIL-STD-1285. 3.11 Recycled, recovered, or environmentally preferable materials. Recycled, re

26、covered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.12 Certificate of compliance. A certificate of complianc

27、e shall be required from manufacturers requesting to be suggested source of supply. 3.13 Workmanship. Resistors shall be processed to be uniform in quality and parts shall be free from defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualifi

28、cation inspection not applicable to this document. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of the group A and B inspections of MIL-PRF-22097. 4.2.2 Certification. The procuring activity may accept a certificate of complia

29、nce in lieu of Group B inspection. 4.3 Visual and mechanical inspection. Resistors shall be inspected to verify that the materials, design, construction, physical dimensions, and workmanship are in accordance with the acceptable requirements (see 3.2 and 3.13). 4.4 Test methods. Test methods specifi

30、ed in 3.3.5 through 3.8 shall be in accordance with MIL-PRF-22097. 4.5 Immersion. The surface of the resistors shall be clean of any foreign matter immediately before immersion. a. Precondition. Precondition resistors in an oven at 125OC 5OC for 13 minutes 2 minutes, or use a fluorocarbon bath maint

31、ained at 125OC 5OC for a period of 1.5 minutes 0.5 minutes. Upon completion of precaution, allow resistors to stabilize to room temperature for approximately 13 minutes 2 minutes. b. Fluorocarbon. Immerse resistors (not to exceed 30 samples) into a bath of fluorocarbon held at 85OC +5OC, -0OC for a

32、period of 60 seconds 5 seconds. Visually examine resistors for inadequate seals, as evidenced by bubbles emanating from any point on the resistors. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packagin

33、g of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or

34、 Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. Provided by IHSNot for ResaleNo reproduct

35、ion or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85085 REV C PAGE 7 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use

36、. Resistors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for the original equipment manufacturer application. Resistor networks described herein are intended for use

37、in electrical circuits where miniaturization is required. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery and one copy of the conformance inspection data or certification of compliance that parts have passed conf

38、ormance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. d. Whether the manufacturer performs the group B tests or provides a certificate of compliance with group B requirements. If purchase order makes no reference to Group B screening the manuf

39、acturer will provide a certification of compliance. 6.3 User of record. Coordination of this document for future revisions are coordinated only with the suggested source of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online

40、 at resistordla.mil or in writing to: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-8754 or DSN 850-8754. 6.4 Suggested source of supply. Suggested source of supply is listed herein. Additional sources will be added as they become available. Assistance in the use

41、of this drawing may be obtained online at resistordla.mil or contact DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-8754 or DSN 850-8754. DSCC drawing PIN Vendor similar designation or type number 1/ Vendor CAGE Vendor name and address 43P* 2/ 02111 Spectrol Electr

42、onics 17070 East Gale Avenue P.O. Box 1220 City of Industry, CA 91745 85085 -* 3006P-1-* 3/ 32997 Bourns, Incorporated 1200 Columbia Avenue Riverside, CA 92507 1/ Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. 2/ Contact resistance variation is 3 percent or 3 ohms, whichever is greater. 3/ Contact resistance variation is 1 percent or 1 ohms, whichever is greater. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-