DLA DSCC-DWG-04055-2007 TOOL INSTALLATION AND REMOVAL TERMINI FIBER OPTIC CABLE ASSEMBLY (CECOM DRAWING A3302584)《光缆组件终端装卸工具( CECOM绘画A3302584)》.pdf

《DLA DSCC-DWG-04055-2007 TOOL INSTALLATION AND REMOVAL TERMINI FIBER OPTIC CABLE ASSEMBLY (CECOM DRAWING A3302584)《光缆组件终端装卸工具( CECOM绘画A3302584)》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-04055-2007 TOOL INSTALLATION AND REMOVAL TERMINI FIBER OPTIC CABLE ASSEMBLY (CECOM DRAWING A3302584)《光缆组件终端装卸工具( CECOM绘画A3302584)》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A 6060-E023 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.100 Selected item drawing REV REV STATUS OF PAGES PAGES 1 2 3 4 5 PMIC N/A PREPARED BY Eugene A. Ebert DESIGN ACTIVITY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH CHECKED BY Eugene A. Ebert APPROVED BY

2、Michael Radecki TITLE TOOL, INSTALLATION AND REMOVAL, TERMINI, FIBER OPTIC CABLE ASSEMBLY (CECOM DRAWING A3302584) SIZE A CODE IDENT. NO. 037Z3 DWG NO. 04055 Original date of drawing 21 March 2007 SCALE N/A REV PAGE 1 OF 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without

3、license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 04055 DWG NO. 04055 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a tool used to install and remove termini from fiber optic connectors per CECOM drawing A3302584. 1.2 Part or Ident

4、ifying Number (PIN). The complete PIN shall be as follows: 04055 | Drawing number 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification o

5、r recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this specification, whether or not they are listed. 2.2 G

6、overnment documents. 2.2.1 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solici

7、tation or contract. CECOM drawing A3302584 Fiber Optic Cable Assemblies (Copies of this drawing are available by email at Charles.Alcottus.army.mil or by calling (732) 532-3741). 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, th

8、e text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. See figure 1. 3.2 Functional. Tool shall be capable of capturing a terminus an

9、d using only hand force applied, the tool shall be capable of compressing the terminus spring. Applying only hand pressure, the tool shall also be capable of lifting the terminus 12 inches above the horizontal surface and holding it for not less than 30 seconds without the terminus falling or being

10、ejected from the tool. With the spring compressed and a wire looped around the exposed termini body diameter, the tool shall be able to exert a force of 16 ounces minimum on the wire. 3.3 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable

11、 materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.4 Materials. Materials utilized shall be selected for wear characteristics. Provided by IHSNo

12、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 04055 DWG NO. 04055 REV PAGE 3 NOTES: 1. Dimensions are in inches. 2. Where jaws are not visually discernable, denotes bottom jaw of tool to facilitat

13、e proper orientation to rear spring compression bushing. 3. Allows clearance for insertion of tool between adjacent termini for jaw lengths (NOTE: This may not apply to optional jaw configuration). 4. Precludes interference between tool and terminus retainer plate for jaw lengths perpendicular to te

14、rminus axis (NOTE: This may not apply to optional jaw configuration). 5. Upper limit of dimension assures that rear spring compression bushing is properly positioned for installation onto terminus retainer plate. Lower limit of dimension prevents over-compression of terminus spring. 6. Metric equiva

15、lents are given for general information only. 7. Tool is designed for use with terminiutilized in connectors perCECOM drawing A3302584. 8. Cutouts in jaws of toolshall be configured to permit entry into the designated areas of the termini. 9. Relationship of the top and bottom jaws of the tool must

16、be as follows: a. Tool includes a stop to prevent over compression ofthe spring (see note 5). b. Compression of the terminus spring to its minimum of .520 inch (13.21 mm) (see note 5),does not result in the terminus being ejected from the tool. 10. Jaw configurations are provided in this figure for

17、guidance only. Optional design variations are allowed, provided performance requirements of 3.2 are met. FIGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A COD

18、E IDENT NO. 04055 DWG NO. 04055 REV PAGE 4 3.5 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.6 Marking. Marking shall consist of the PIN as specified herein (see 1.2), the manufacturers name or Commercial

19、and Government Entity (CAGE) code, and date lot codes. 3.7 Workmanship. The tool shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Sampling and inspection. Unless otherwise specified, sampling and inspection procedures sha

20、ll be performed in accordance with conformance inspection specified using sampling plan indicated. 4.1.1 Conformance inspection. Conformance inspection shall consist of inspections necessary to verify compliance to figure 1 or optional configuration allowed and requirements listed herein including t

21、he functional requirement (see 3.2). 4.1.2 Sampling plan. A sample of parts shall be randomly selected from each lot in accordance with table I, if one or more defects are found, the lot shall be rescreened and defects removed. After screening and removal of defects, a new sample of parts shall be r

22、andomly selected using the sample size of the next larger lot size specified in table I. If one or more defects are found in the second sample, the lot shall be rejected and shall not be supplied to this drawing. TABLE I. Conformance inspection sampling plan Lot size Sample size 1 to 26 to 51 to 91

23、to 151 to 281 to 501 to 1,201 to 3,201 to 10,001 and 2550901502805001,2003,20010,000over3 5 6 7 10 11 15 18 22 29 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed b

24、y DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the mili

25、tary services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES 6.1 Intended use. This tool is intended to be used for installation

26、 and removal of termini from second generation tactical fiber optic connectors. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 04055 DWG NO. 04055 REV PAGE 5 6.2 Ordering data. The

27、 contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements

28、 for packaging and packing. 6.3 Users of record. Coordination of this document for future revisions is coordinated only with the suggested sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at TubesFiberOpticdla.

29、mil or if in writing to: Defense Supply Center, Columbus, ATTN: DSCC/VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0729 or DSN 850-0729. 6.4 Suggested sources of supply. Suggested sources of supply are listed herein (see table II). Additional sources will be added as t

30、hey become available. Assistance in the use of this drawing may be obtained online at FiberOpticGroupdscc.dla.mil or by contacting Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0729 or DSN 850-0729. TABLE II. Suggested source

31、s of supply. DSCC drawing PIN Vendor similar designation or type number 1/ Vendor CAGE Vendor name and address 04055 FSTP 0645 0YMP4 Amphenol Fiber Systems International 1300 Central Expressway North Suite 100 Allen, TX 75013 http:/ 04055 182-010 06324 Glenair 1211 Air Way Glendale, CA 91201-2497 ht

32、tp:/ 04055 0731-1132 08RC6 Kitco Fiber Optics 5269 Cleveland Street Virginia Beach, VA 23462-6556 http:/ 04055 420-0125 1HVU5 Stran Technologies 39 Great Hill Road Naugatuck, CT 06770 http:/ 1/ Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-