DLA A-A-59733-2002 CAP LUBRICATION FITTING《螺帽润滑装置》.pdf

《DLA A-A-59733-2002 CAP LUBRICATION FITTING《螺帽润滑装置》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59733-2002 CAP LUBRICATION FITTING《螺帽润滑装置》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 INCH-POUND A-A-59733 5 December 2002 SUPERSEDING CS4730-0005 12 July 1977 COMMERCIAL ITEM DESCRIPTION CAP LUBRICATION FITTING The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This CID covers the general requirements f

2、or Lubrication Fitting Caps. Caps covered by this CID are intended for commercial/industrial applications. 2. CLASSIFICATION. This CID uses a classification system which is included in the Part Identification Number (PIN) as shown (see 7.1). PIN Color AA59733-001 Black AA59733-002 Blue AA59733-003 B

3、rown AA59733-004 Green AA59733-005 Red AA59733-006 White AA59733-007 Yellow 3. SALIENT CHARACTERISTICS. 3.1 Dimensions. Cap(s) supplied to this CID shall be as specified herein and figure 1. 3.2 Material. The material shall conform to ASTM D4976, Group 2, Class 3 or 4. 3.3 Marking. Cap(s) supplied t

4、o this CID shall have the manufacturers (MFRs) standard commercial part number and this CID PIN marked as specified in the contract or order (see 7.4). 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with pa

5、ragraph 23.403 of the Federal Acquisition Regulation (FAR). Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data which may improve this document should be sent to: Defense Supply Center, Columbus, ATTN: DSCC-VAI, Post Office Box 3990, Columbus OH 43216-5000,

6、 or telephone (614) 692-0538, or facsimile (FAX) (614) 692-6939. AMSC N/A FSC 4730DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59733 SR.250.062.050.240.190.290.3

7、64.420.480.240.100.187NOTES:1. DIMENSIONS ARE IN INCHES.2. TOLERANCE: DECIMALS .010 UNLESS OTHERWISE SPECIFIED.250.270Figure 1. Cap lubrication fitting. 5. PRODUCT CONFORMANCE PROVISIONS. 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to th

8、e producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. 6. PACKAGING. Preservation, packing, and marking shall be as specified in t

9、he contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2 for PIN format example. 7.2 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and submission of these caps to DSCC under

10、 the Military Parts Control Advisory Group (MPCAG) evaluation program, CAGE code 58536 should be used. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59733 7.3 Source of documents. INDUSTRY STANDARDS AMERICAN SOCIETY FOR TESTING AND MATERIALS

11、ASTM D4976 - Standard Specification for Polyethylene Plastics Molding and Extrusion Materials. (Application for copies should be addressed to the Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19248-2959.) (Industry association specifications and standards are genera

12、lly available for reference from libraries. They are also distributed among technical groups and using Federal agencies.) 7.4 Ordering data. The contract or order should specify the following: a. CID document number, revision, and PIN. b. Marking requirements (see 3.3). c. Product conformance provis

13、ions (see 5.1). d. Packaging requirements. 7.5 Commercial products. As part of the market analysis and research effort, this CID was coordinated with the following manufacturers of commercial products. At the time of CID preparation and coordination, these manufacturers were known to have commercial

14、 products that would meet the requirements of this CID. (NOTE: This information should not be considered as a list of approved manufacturers or used to restrict procurement to only the manufacturers shown.) 3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH

15、S-,-,-A-A-59733 MFRs CAGE MFRs Name & Address 23540 Niagara Plastics 7090 Edinboro Road Erie, PA 16509-4497 Phone 1-800-457-5236, 1-800-485-0465 1-814-868-3671 FAX 1-800-358-4391 E-MAIL - URL http:/ 1L397 GKS Inc. 25670 1st Street Westlake, OH 4145 03296 Nylon Molding Corp NMC Group Inc. 2755 Thomp

16、son Creek Road Pomona, CA 91767-1861 E-Mail - 050R4 Patriot Logistics 86 Broadway Freeport, NY 11520-0000 Phone 1-516-377-3300 Fax 1-516-377-4373 E-Mail - 62727 Mid-State Sales Inc. 1101 Gahanna Parkway Columbus, OH 43230-6600 Phone 1-614-864-1811 E-Mail - jodi.maynardmidstate- 8N281 Edwards Aircr

17、aft Co. 6050 Grissom Parkway Titusville, FL 32780-7903 60117 Rosco Intl Corp 95 N. Remington Road Columbus, OH 43209-1442 Phone 1-614-497-8119 Fax 1-614-497-1905 28375 Spectron Inc.14 Bates Street Dayton, OH 45402-1326 Phone 1-937-461-5590 Fax 1-937-461-5594 E-Mail - 7.6 Part number (P/N) supersess

18、ion data. These CID part numbers, Table I, supersede the part numbers identified on Defense Construction Supply Center drawing CS-4730-0005 which is cancelled. This information is being provided to assist in reducing proliferation in the Government inventory system. 4Provided by IHSNot for ResaleNo

19、reproduction or networking permitted without license from IHS-,-,-A-A-59733 TABLE I. P/N data. Part number Drawing P/N (NAVORD) MFRs CAGE MFRs P/N 1/ NSN AA59733-001 CS4730-0005PC6 12-Z-12163-6 23540 1L397 522 4730-00-270-3916 AA59733-002 CS4730-0005PC4 12-Z-12163-4 03296 4730-00-270-3917 AA59733-00

20、3 CS4730-0005PC5 12-Z-12163-5 4730-00-270-3918 AA59733-004 CS4730-0005PC3 12-Z-12163-3 050R4 4730-00-270-3919 AA59733-005 CS4730-0005PC1 12-Z-12163-1 62727 4730-00-270-3920 AA59733-006 CS4730-0005PC7 12-Z-12163-7 8N281 28375 60117 4730-00-270-3921 AA59733-007 CS4730-0005PC2 12-Z-12163-2 4730-00-27-3

21、922 1/ The manufacturers P/N shall not be used for procurement to the requirements of this CID. At the time of preparation of this CID, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. For actual part marking requirements see 3.3. 7.7 Government users.

22、 To acquire information on obtaining these Caps from the Government inventory system, contact the DSCC call center: Defense Supply Center Columbus Cffice Code: DSCC-AB, Post Office Box 3990, Columbus, OH 43216-5000, or telephone (614) 692-2771, or (614) 692-3191. 7.7.1 National stock number (NSN). T

23、able I includes a list of NSNs assigned which correspond to this CID. The list is for information only and may not be indicative of all possible NSNs associated with this CID. For up to date information on assigned NSNs, please contact the aforementioned DSCC office (See 7.7). MILITARY INTEREST: CIVIL AGENCY COORDINATING ACTIVITY: GSA/FSS Custodians: Preparing activity: Army - AV DLA - CC Navy - AS (Project 4730-2174) Review activities: Navy - SA, OS 5Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-