DLA A-A-59554 A-2009 CORRUGATED COLLAPSIBLE REUSABLE BULK PACKING SYSTEM.pdf

《DLA A-A-59554 A-2009 CORRUGATED COLLAPSIBLE REUSABLE BULK PACKING SYSTEM.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59554 A-2009 CORRUGATED COLLAPSIBLE REUSABLE BULK PACKING SYSTEM.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 3990 A-A-59554A 4 August 2009 SUPERSEDING A-A-59554 21 December 2004 COMMERCIAL ITEM DESCRIPTION CORRUGATED COLLAPSIBLE REUSABLE BULK PACKING SYSTEM The General Services Administration has authorized the use of this Commercial Item Description for all Federal Agencies. 1. SCOPE. This sp

2、ecification covers the minimum requirements of corrugated box and pallet system used in the Defense Depots. 2. CLASSIFICATION. 2.1 Classification. Corrugated collapsible reusable bulk packing system will be of the following styles, entry designation, and weather resistant designation, as specified.

3、2.1.1 Style: “A” 48”Length X 40” Width Pallet with 30 cubic feet Box “B” 48”Length X 40” Width Pallet with 20 cubic feet Box 2.1.2 Entry designation: “2” Two Way Entry “4” Four Way Entry 2.1.3 Weather resistant designation: “W” Weather Resistant Material “ ” Non-Weather Resistant Material 2.2 Part o

4、r Identifying Number (PIN): The following PIN procedure is for government purposes and does not constitute a requirement for the contractor. This example describes a PIN for CID A-A-59554. AA59554-B-2-W Weather resistant designator (see 2.1.3) Entry designator (see 2.1.2) Style (see 2.1.1) Basic CID

5、 number 48”Length X 40” Width Pallet with 20 cubic feet Box - Two Way Entry Weather Resistant INCH-POUND Comments, suggestions, or questions on this document should be addressed to Defense Supply Center Philadelphia (DSCP), ATTN: DSCP-NASA, 700 Robbins Avenue, Philadelphia, PA 19111-5096 or e-mail t

6、o dscpg&inspecommentsdla.mil . Since contact information can change, you may want to verify the currency of this address information using ASSIST Online database at http:/assist.daps.dla.mil .Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59554A

7、 2 3. SALIENT CHARACTERISTICS. 3.1 Reclaimable material. Bulk packing system shall be 100% recyclable. 3.2 Set-up. Bulk packing system shall be designed to be both set-up and knock down, one-man operation. 3.3 Collapsibility. Box component shall collapse upon corrugated pallet. Lid will fit snuggly

8、over collapsed unit. Unit shall have a height no greater than 12 total. The pallet height shall be no greater than 6” maximum. 3.4 Pallet construction. Pallet upper deck corrugated material shall be a minimum of 275 lb/sq. inch (psi) double-wall. Pallet lower deck (bottom surface) corrugated materia

9、l shall be 2 laminated sheets of 275 lb/msf double wall. Pallets shall have either 9 cores or 3 stringers minimum. Cores and stringers shall be wrapped to in place to help secure and prevent shifting and shearing. Forklift tine positions shall be a minimum of 7.50” and a maximum of 12”. The forklift

10、 tine opening shall begin at 8.25” 8.50” from each end on all sides. The height of the forklift tine opening shall be 3” minimum. 3.5 Box construction. Box corrugated material shall be a minimum of 400 psi double-wall. Style shall be Half Slotted Container (HSC) with Regular Slotted Container (RSC)

11、bottom. Fluting shall be vertical to the depth of the box. Box maximum capacity shall be 2500 pounds. 3.6 Weather resistant material. When specified, single face flute shall include a water resistant resin to enhance and ensure flute formation and bonding. All water resistant pallets shall be assemb

12、led using a high performance water based adhesive product, developed to bond paper. 3.7 Adhesive. Box, pallet and lid shall use waterproof adhesive (WPA) in construction. 3.8 Box attachment. Box shall be attached to corrugated pallet. Pallet and box shall be of singular construction. 3.9 Bottom surf

13、ace. The load-bearing surface in contact with the ground (pallet footprint) shall be a minimum of 40 percent of the top deck area. 3.10 Flatness. When the pallet bottom is placed on a flat surface, the pallet top shall not vary more than 0.25” from the average pallet height. 3.11 Box lid material. L

14、id-corrugated material shall be a minimum of 400 psi double-wall. 3.12 Identification marking. The following marking shall be applied to the pallet for identification: Box certification stamp and manufacturers CAGE code. 4. PRODUCT CONFORMANCE PROVISION. 4.1 Product conformance. The products provide

15、d shall meet the salient characteristics of this commercial item description, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The government reserves the right to require proof of su

16、ch conformance. 4.2 Inspection. The bulk packing system shall be inspected as specified below to determine compliance with all requirements specified in this CID. 4.2.1 Pallet component. Measure the pallet length and width. The length and the width of the pallet shall be within specified style plus

17、or minus tolerance of 0.25”. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59554A 3 4.2.2 Box component. Measurement of the cubic feet of the fully assembled box within specified style shall have a plus or minus tolerance of 1%. 4.2.3 Entry. Fo

18、rks shall be fully extended through the shorter side of the pallet. Pallet jack entry need only be 2 way. 4.2.4 Bottom surface. Measure the bottom deck and calculate 40 percent of the top deck area. 4.2.5 Forklift tine openings: The openings on the four pallet sides shall be measured and shall be wi

19、thin as specified (see 3.4). 4.2.6 Height. The height of a bulk packing system shall be measured not to exceed 12” in the collapsed mode. 4.2.7 Flatness. Measure the pallet height at the four corners and at the midpoints of the perimeter. Average the eight measurements. Place the pallet on a flat su

20、rface. At the same eight points, measure the distance from the flat surface to the pallet top. No measurement shall exceed the average pallet height by more then 0.25”. 4.2.8 Squareness. Measure the two diagonals of the top deck. The differences of the two measurements shall not be greater than 0.75

21、”. 4.2.9 Identification marking. Visually inspect for presence of identification markings. 4.2.10 Compression test. Box compression shall meet an average of 3500 lb. compression at 1.270 inches, in accordance with ASTM D4577 (Section 7.2 no fewer than 5 samples). 4.2.11 Board flexural rigidity test.

22、 Board shall meet an average flex rigidity value tested on a Composite Flex Tester of 70 N-m on combined board samples (no fewer than 5 samples). 4.2.12 Resiliency. Bulk packing system shall be capable of withstanding automatic banding equipment and moving through an automated conveyor system. 5. PA

23、CKAGING. Preservation, packing and marking shall be as specified in the contract or order. 6. NOTES. 6.1 Ordering data. The contract or order should specify the following: a. CID document number, revision, and CID PIN. b. Packaging requirements. 6.2 Styles C,D, E, and F are deleted under this revisi

24、on without replacement. 6.3 Sources of documents. 6.3.1 ASTM International standards. ASTM standards are available online at www.astm.org or from ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. ASTM D4577 - Standard Test Method for Compression Resistance of a Container U

25、nder Constant Load 6.4 Key words. Box Lid Pallet Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59554A 4 6.5 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due

26、 to the extent of the changes. Military interests: Custodians: Preparing activty: Army AV DLA - IS Navy SA Air Force 99 (Project 3990-2009-002) Review activity: Air Force - 84 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-