DLA A-A-59230-1998 FLUID MAGNETIC PARTICLE INSPECTION SUSPENSION《悬浮磁性粒子检验流度》.pdf

《DLA A-A-59230-1998 FLUID MAGNETIC PARTICLE INSPECTION SUSPENSION《悬浮磁性粒子检验流度》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59230-1998 FLUID MAGNETIC PARTICLE INSPECTION SUSPENSION《悬浮磁性粒子检验流度》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、METRICA-A-592302 J uly 1998SUPERSEDINGDOD-F-8793512 J anuary 1984Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any otherdata which may improve this document should be sent to: Defense Supply Center Richmond(DSCR), ATTN: DSCR-VBD, 8000 Jefferson Davis Highway, R

2、ichmond, VA 23297-5678.AMSC N/A FSC 6850DISTRIBUTION STATEMENT A . Approved for public release; distribution is unlimited.COMMERCIAL ITEM DESCRIPTIONFLUID, MAGNETIC PARTICLE INSPECTION, SUSPENSIONThe General Services Administration has authorized the use of this commercialitem description as a repla

3、cement for DOD-F-87935 for all federal agencies.1. SCOPE. This commercial item description (CID) covers a petroleum-base fluid for use as asuspension vehicle while performing magnetic particle nondestructive inspection procedures.2. SALIENT CHARACTERISTICS2.1 General . The magnetic particle suspensi

4、on fluid characteristics shall conform to all therequirements of Type 1 product specified in AMS 2641, Vehicle, Magnetic Particle Inspection(Petroleum Based). In addition, the suspension fluid when tested in accordance with test methodsspecified in AMS 2641, shall conform to the adjusted technical r

5、equirements as follows:2.1.1 Fluorescence . The fluid fluorescence shall not exceed that of a 1 part per million (ppm) byweight reference standard solution.2.1.2 Particulate matter . The particulate matter in the fluid shall not exceed 0.5 milligram perliter (mg/L).2.1.3 Total acid number . The flui

6、d total acid number shall not exceed 0.015 mg of potassiumhydroxide (KOH) per gram.2.1.4 Color . The fluid color shall not be darker than 1.0 ASTM Color when tested in accordancewith ASTM D1500, Standard Test Method for ASTM Color of Petroleum Products (ASTMColor Scale).Provided by IHSNot for Resale

7、No reproduction or networking permitted without license from IHS-,-,-A-A-5923023. REGULATORY REQUIREMENTS3.1 Material safety data sheet . Manufacturers shall prepare and submit a material safety datasheet (MSDS) in accordance with FED-STD-313 and meeting the Code of Federal Regulationsrequirements o

8、f 29 CFR 1910.1200.4. QUALITY ASSURANCE PROVISIONS4.1 Product conformance . The products provided shall meet the salient characteristics of thiscommercial item description, shall conform to the producers own drawings, specifications,standards, and quality assurance practices, and shall be the same p

9、roduct offered for sale in thecommercial market. The government reserves the right to require proof of such conformance.5. PACKAGING5.1 Preservation, packing, and marking . For acquisition purposes, the magnetic particlesuspension vehicle fluid shall be preserved, packed, and marked as specified in

10、the contract ororder.6. NOTES6.1 Sources of documents .6.1.1 Copies of SAE standards may be obtained from Society of Automotive EngineersInternational, 400 Commonwealth Drive, Warrendale, PA 15095-0001.6.1.2 Copies of ASTM standards may be obtained from the American Society for Testing andMaterials,

11、 100 Barr Harbor Dr., West Conshohocken, PA 19428-2959.6.1.2 For bidding purposes, copies of FED-STD-313 may be obtained from the General ServicesAdministration, Federal Supply Service Bureau, Specification Section, Suite 8100, 479 LEnfantPlaza SW, Washington, DC 20407.6.2 National stock number (NSN

12、) . This CID is associated with NSN 6850-01-196-5472. OtherNSNs may correspond with this document.MILITARY INTERESTS:Custodians:Air Force - 68Army - AVNavy - ASPreparing activity:DLA - GS(Project 6850-1188)Reviewers:Air Force - 11Navy - SHProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-