DIN EN ISO 9117-1-2009 Paints and varnishes - Drying tests - Part 1 Determination of through-dry state and through-dry time (ISO 9117-1 2009) English version of DIN EN ISO 9117-1 2.pdf

《DIN EN ISO 9117-1-2009 Paints and varnishes - Drying tests - Part 1 Determination of through-dry state and through-dry time (ISO 9117-1 2009) English version of DIN EN ISO 9117-1 2.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 9117-1-2009 Paints and varnishes - Drying tests - Part 1 Determination of through-dry state and through-dry time (ISO 9117-1 2009) English version of DIN EN ISO 9117-1 2.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、October 2009DEUTSCHE NORM English price group 8No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 87.040!$ZX“1552953www.d

2、in.deDDIN EN ISO 9117-1Paints and varnishes Drying tests Part 1: Determination of through-dry state and through-dry time(ISO 9117-1:2009)English version of DIN EN ISO 9117-1:2009-10Beschichtungsstoffe Trocknungsprfungen Teil 1: Bestimmung des Durchtrocknungszustandes und der Durchtrocknungszeit(ISO

3、9117-1:2009)Englische Fassung DIN EN ISO 9117-1:2009-10SupersedesDIN EN 29117:1992-09www.beuth.deDocument comprises pages14 2 DIN EN ISO 9117-1:2009-10 National foreword This standard has been prepared by Technical Committee ISO/TC 35 “Paints and varnishes”, Subcommittee SC 9 “General test methods f

4、or paints and varnishes” (Secretariat: BSI, United Kingdom) in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Beschichtungsstoffe und Beschichtungen (Coatings and Co

5、ating Materials Standards Committee), Technical Committee NA 002-00-07 AA Allgemeine Prfverfahren fr Beschichtungsstoffe und Beschichtungen. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 48 DIN ISO 48 ISO 1513 DIN EN ISO 1513 ISO 1514

6、 DIN EN ISO 1514 ISO 2808 DIN EN ISO 2808 ISO 3678 DIN EN ISO 3678 ISO 4622 DIN EN ISO 4622 ISO 15528 DIN EN ISO 15528 Amendments This standard differs from DIN EN 29117:1992-09 as follows: a) In the German version, the evaluation criterion is designated as Beschdigung (damage) and no longer as Besc

7、hdigung oder Abdruck. b) The previous Annex A has been incorporated in the text of the standard. c) The number of the standard has been changed from DIN EN 29117 into DIN EN ISO 9117-1. d) The standard has been editorially revised. Previous editions DIN EN 29117: 1992-09 3 National Annex NA (informa

8、tive) Bibliography DIN EN ISO 1513, Paints and varnishes Examination and preparation of samples for testing DIN EN ISO 1514, Paints and varnishes Standard panels for testing DIN EN ISO 2808, Paints and varnishes Determination of film thickness DIN EN ISO 3678, Paints and varnishes Print-free test DI

9、N EN ISO 4622, Paints and varnishes Pressure test for stackability DIN EN ISO 15528, Paints, varnishes and raw materials for paints and varnishes Sampling DIN ISO 48, Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD) DIN EN ISO 9117-1:2009-10 4 Thi

10、s page is intentionally blank DIN EN ISO 9117-1:2009-10 EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 9117-1May 2009ICS 87.040 Supersedes EN 29117:1992 English VersionPaints and varnishes - Drying tests - Part 1: Determination ofthrough-dry state and through-dry time (ISO 9117-1:2009)Peintur

11、es et vernis - Essais de schage - Partie 1:Dtermination du schage coeur et du temps de schage coeur (ISO 9117-1:2009)Beschichtungsstoffe - Trocknungsprfungen - Teil 1:Bestimmung des Durchtrocknungszustandes und derDurchtrocknungszeit (ISO 9117-1:2009)This European Standard was approved by CEN on 23

12、April 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obta

13、ined on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Manageme

14、nt Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, P

15、oland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any

16、 means reservedworldwide for CEN national Members.Ref. No. EN ISO 9117-1:2009: EEN ISO 9117-1:2009 (E) 2 Contents Page Foreword .3 1 Scope4 2 Normative references4 3 Terms, definitions and abbreviated terms4 4 Principle .5 5 Apparatus and materials 5 6 Sampling 7 7 Test panels.7 7.1 Substrate 7 7.2

17、Preparation and coating .7 8 Procedure.8 8.1 Preparation of apparatus8 8.2 Drying the test panel.8 8.3 Determination of through-dry state .8 8.4 Determination of through-dry time 8 8.5 Thickness of coating.9 9 Precision 9 10 Test report9 Bibliography10 DIN EN ISO 9117-1:2009-10 EN ISO 9117-1:2009 (E

18、) 3 Foreword This document (EN ISO 9117-1:2009) has been prepared by Technical Committee ISO/TC 35 Paints and varnishes in collaboration with Technical Committee CEN/TC 139 Paints and varnishes t which is held by DIN. This European Standard shall be given the status of a national standard, either by

19、 publication of an identical text or by endorsement, at the latest by November 2009, and conflicting national standards shall be withdrawn at the latest by November 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or

20、CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 29117:1992. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belg

21、ium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice

22、 The text of ISO 9117-1:2009 has been approved by CEN as a EN ISO 9117-1:2009 without any modification. DIN EN ISO 9117-1:2009-10 “” he secretariat of1 Scope This part of ISO 9117 specifies a test method for determining under standard conditions whether a single coat or a multi-coat system of paint,

23、 varnish or related material has reached the through-dry state after a specified drying period. NOTE The test procedure may also be used to determine the time taken to achieve that state. 2 Normative references The following referenced documents are indispensable for the application of this document

24、. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 48, Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD) ISO 1513, Paints and varnish

25、es Preparation of test samples ISO 1514, Paints and varnishes Standard panels for testing ISO 2808, Paints and varnishes Determination of film thickness ISO 15528, Paints, varnishes and raw materials for paints and varnishes Sampling 3 Terms, definitions and abbreviated terms For the purposes of thi

26、s document, the following terms, definitions and abbreviated terms apply. 3.1 IRHD scale international rubber hardness degree scale 3.2 through-dry state condition of a film in which it is dry throughout its thickness NOTE 1 The through-dry state should not be confused with the condition in which th

27、e surface of the film is dry but the bulk of the coating is still mobile. DIN EN ISO 9117-1:2009-10 EN ISO 9117-1:2009 (E) 4NOTE 2 For the purposes of this part of ISO 9117, a single coating or a multi-coat system of paint or varnish or related material is considered to be through-dry when a specifi

28、ed gauze under specified pressure, torsion and time does not damage the film. 3.3 through-dry time period of time between the application of a coat to a prepared test panel and the achievement of the through-dry state, as determined by the specified test procedure 4 Principle A coat of paint or varn

29、ish of agreed thickness is applied to a substrate and is allowed to dry under specified conditions. The completeness of drying throughout the coat is determined by examination of the surface of the coat after the application of a load, applied over a given area of the surface, and subsequent rotatio

30、n of the load-applying face through 90. 5 Apparatus and materials Ordinary laboratory apparatus and glassware together with the following: 5.1 Baseplate and plunger assembly (see Figure 1 and Figure 2), consisting essentially of a baseplate and a free-sliding plunger. The plunger head shall have a d

31、iameter of at least 25 mm. It shall be designed in such a way that the underside of the head can align itself with the upper surface of the test panel. NOTE 1 If the mass of the plunger is not greater than 250 g, the apparatus described in ISO 46221is suitable for the test. DIN EN ISO 9117-1:2009-10

32、 EN ISO 9117-1:2009 (E) 5 Key 1 weights 2 plunger 3 ball joint 4 plunger head 5 baseplate Figure 1 Baseplate and plunger assembly A rubber disc (5.2) shall be attached to the centre of the underside of the plunger head using tape coated on both sides with adhesive. There shall be a device to firmly

33、clamp a gauze (5.3) to the test face, and the plunger head shall be able to be rotated through 90. NOTE 2 It is recommended that a ball-joint connection be present between the plunger and its head and that, for reasons of economy, the plunger specified in ISO 4622 be used. 5.2 Flat rubber disc, of d

34、iameter (22 1) mm, thickness (5 0,5) mm and hardness (50 5) IRHD (see ISO 48). NOTE For reasons of economy, it is recommended that the rubber disc specified in ISO 36782be used. 5.3 Gauze, of woven monofilament polyamide, minimum size 100 mm 100 mm. The gauze thread diameter shall be 0,120 mm and th

35、e gauze aperture approximately 0,2 mm. 5.4 Weights, giving a total mass of (1 500 10) g. 5.5 Stopwatch, accurate to 0,1 s. DIN EN ISO 9117-1:2009-10 EN ISO 9117-1:2009 (E) 6 Key 1 plunger 2 clip 3 rod for rotating plunger head 4 gauze 5 double-faced adhesive tape 6 rubber disc Figure 2 Detail showin

36、g assembled plunger head 6 Sampling Take a representative sample of the product to be tested (or of each product in the case of a multi-coat system), as described in ISO 15528. Examine and prepare each sample for testing, as described in ISO 1513. 7 Test panels 7.1 Substrate Select as the substrate

37、three test panels (or six if both the through-dry state and the through-dry time are to be determined) of a type described in ISO 1514, where possible ensuring that the substrate is equivalent to the intended application. 7.2 Preparation and coating Prepare the test panels (see 7.1) in accordance wi

38、th ISO 1514 and then coat them with the product or system under test by the specified method to the thickness specified for the dry film. The coating method and dry film thickness shall be as specified by the manufacturer, or agreed between interested parties, and included in the test report see Cla

39、use 10, items c) 2) and c) 3). DIN EN ISO 9117-1:2009-10 EN ISO 9117-1:2009 (E) 78 Procedure 8.1 Preparation of apparatus Clamp the gauze (5.3) over the rubber disc (5.2) under the plunger head (see Figure 2), taking care to ensure that the exposed surface of the gauze is free from creases. Take a f

40、resh piece of gauze for each test. 8.2 Drying the test panel Dry (or stove) and age, if applicable, each coated test panel in a horizontal position with free circulation of air, but shielded from draughts and direct sunlight, for the specified time under the specified conditions. The drying (or stov

41、ing) and aging time and conditions shall be as specified by the manufacturer, or agreed between the interested parties, and included in the test report see Clause 10, items c) 4) and c) 5). 8.3 Determination of through-dry state 8.3.1 On completion of the specified drying time (see 8.2), place a tes

42、t panel on the baseplate. 8.3.2 Place the weights (5.4) on the top of the plunger. Gently lower the plunger so that the gauze is in contact with the test panel. Start the stopwatch (5.5) and allow the plunger to remain in this position for (10 1) s. 8.3.3 At the end of this period, turn the plunger

43、head through an angle of 90 over a period of about 2 s. Immediately raise the plunger, remove the test panel and examine the coat in the test area using the naked eye. 8.3.4 Repeat the procedure in 8.3.1 to 8.3.3 on two additional coated panels. 8.3.5 If no damage is observed on any of the three tes

44、t surfaces, report the result as “through-dry state achieved”. If damage is observed on one or more of the three test surfaces, report the result as “through-dry state not achieved”. Some coatings do not reach a point where they are totally unaffected by the test (i.e. a point where no mark, for ins

45、tance, is left on the surface by the gauze), even when they have reached a functionally acceptable state of drying or cure. In such cases, the time when the coating reaches the stage at which the action carried out in the test does not cause deterioration of the coating to an extent where it could n

46、ot perform its ultimate function shall be quoted. For some coatings, e.g. those which are applied to protect the substrate rather than for cosmetic reasons, marking of the surface would not constitute an inability of the coating to perform its function. For highly pigmented coatings, the action of t

47、he gauze can cause polishing of the surface, leaving marks which might not be detrimental to the coatings ultimate function. In such cases, all observations shall be recorded in the test report. Take care to avoid confusion between cohesive failure within the coat (a failure under this test) and fai

48、lure of the coat to adhere to the substrate (not a failure under this test). 8.4 Determination of through-dry time 8.4.1 On completion of the specified drying time (see 8.2), place a test panel on the baseplate. 8.4.2 At appropriate intervals, carry out the test described in 8.3.2 and 8.3.3. Examine

49、 the coating in the test area for damage. Stop the test when no damage occurs to the coat (see 8.3.5). 8.4.3 Repeat the procedure in 8.4.1 and 8.4.2 on two additional coated panels. 8.4.4 Report the longest time taken in the three tests for the coat to reach the through-dry state. DIN EN ISO 9117-1:2009-10 EN ISO 9117-1:2009 (E) 8 8.5 Thickness of coating Determine the thickness, in micrometres, of the coat in the through-dry state by one of the procedures specified in ISO 2808, using an untested area of