DIN EN ISO 9073-17-2008 Textiles - Test methods for nonwovens - Part 17 Determination of water penetration (spray impact) (ISO 9073-17 2008) German version EN ISO 9073-17 2008《纺织物 .pdf

《DIN EN ISO 9073-17-2008 Textiles - Test methods for nonwovens - Part 17 Determination of water penetration (spray impact) (ISO 9073-17 2008) German version EN ISO 9073-17 2008《纺织物 .pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 9073-17-2008 Textiles - Test methods for nonwovens - Part 17 Determination of water penetration (spray impact) (ISO 9073-17 2008) German version EN ISO 9073-17 2008《纺织物 .pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、September 2008DEUTSCHE NORM English price group 8No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 59.080.30!$Qf“1466727

2、www.din.deDDIN EN ISO 9073-17Textiles Test methods for nonwovens Part 17: Determination of water penetration (spray impact)(ISO 9073-17:2008)English version of DIN EN ISO 9073-17:2008-09Textilien Prfverfahren fr Vliesstoffe Teil 17: Bestimmung der Wasserdurchdringung (Sprhverfahren) (ISO 9073-17:200

3、8)Englische Fassung DIN EN ISO 9073-17:2008-09www.beuth.deDocument comprises 13 pagesDIN EN ISO 9073-17:2008-09 2 National foreword This standard has been published in accordance with a decision taken by Technical Committee CEN/TC 248 “Textiles and textile products” (Secretariat: BSI, United Kingdom

4、) to adopt International Standard ISO 9073-17:2008 as a European Standard. ISO 9073-17:2008 was prepared by Technical Committee ISO/TC 38 “Textiles”. At present a DIN committee does not exist for this standard since the parties concerned have not shown any interest in work on the subject. The Normen

5、ausschuss Materialprfung (Materials Testing Standards Committee) is obliged to publish the standard, however, as the subject falls in its domain. DIN EN ISO 9073 consists of the following parts, under the general title Textiles Test methods for nonwovens: Part 2: Determination of thickness Part 4: D

6、etermination of tear resistance Part 5: Determination of resistance to mechanical penetration (ball burst procedure) (at draft stage) Part 6: Absorption Part 7: Determination of bending length Part 8: Determination of liquid strike-through time (simulated urine) Part 9: Evaluation of drapability inc

7、luding drape coefficient Part 10: Lint and other particles generation in the dry state Part 11: Run-off Part 12: Demand absorbency Part 13: Repeated liquid strike-through time Part 14: Coverstock wetback Part 15: Determination of air permeability Part 18: Determination of breaking strength and elong

8、ation of nonwoven materials using the grab tensile test The following parts of ISO 9073 under the general title Textiles Test methods for nonwovens are only available as International Standards: Part 1: Determination of mass per unit area Part 3: Determination of tensile strength and elongation Part

9、 16: Determination of resistance to penetration by water (hydrostatic pressure) Part 17: Determination of water penetration (spray impact) DIN EN ISO 9073-17:2008-09 3 The DIN Standards corresponding to the International Standards referred to in the EN are as follows: ISO 139 DIN EN ISO 139 ISO 9073

10、-6 DIN EN ISO 9073-6 National Annex NA (informative) Bibliography DIN EN ISO 139, Textiles Standard atmospheres for conditioning and testing DIN EN ISO 9073-6, Textiles Test methods for nonwovens Part 6: Absorption DIN EN ISO 9073-17:2008-09 4 This page is intentionally blank EUROPEAN STANDARD NORME

11、 EUROPENNE EUROPISCHE NORM EN ISO 9073-17 May 2008 ICS 59.080.30 English Version Textiles - Test methods for nonwovens - Part 17: Determination of water penetration (spray impact) (ISO 9073-17:2008) Textiles - Mthodes dessai pour nontisss - Partie 17: Dtermination de la pntration de leau (impact dar

12、osol) (ISO 9073-17:2008) Textilien - Prfverfahren fr Vliesstoffe - Teil 17: (ISO 9073-17:2008) This European Standard was approved by CEN on 14 May 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the sta

13、tus of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German).

14、A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republ

15、ic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE N

16、ORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 9073-17:2008: EBestimmung der Wasserdurchdringung (Sprhverfahren) 2 DIN EN

17、ISO 9073-17:2008-09 - : -EN ISO 9073-17:2008 (E) Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Principle4 5 Materials and reagents5 6 Apparatus .5 7 Procedure .5 8 Calculation6 9 Test report 6 Annex A (informative) General information regarding reproducibili

18、ty9 3 EN ISO 9073-17:2008 (E) DIN EN ISO 9073-17:2008-09 Foreword This document (EN ISO 9073-17:2008) has been prepared by Technical Committee ISO/TC 38 “Textiles“ in collaboration with Technical Committee CEN/TC 248 “Textiles and textile products” the secretariat of which is held by BSI. This Europ

19、ean Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2008, and conflicting national standards shall be withdrawn at the latest by November 2008. Attention is drawn to the possibility that some of the el

20、ements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this

21、European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the Un

22、ited Kingdom. Endorsement notice The text of ISO 9073-17:2008 has been approved by CEN as a EN ISO 9073-17:2008 without any modification. 1 Scope This part of ISO 9073 specifies a method for measuring the resistance of fabrics to the penetration of water by impact. The water penetration (spray impac

23、t) test is applicable to fabrics that are expected to exhibit a degree of water resistance or water repellency. The results obtained with this method depend on the water repellency of the fibres or the treatment applied to the finished material, as well as on the construction of the material. 2 Norm

24、ative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 139, Textiles Standard atmos

25、pheres for conditioning and testing ISO 3951-5, Sampling procedures for inspection by variables Part 5: Sequential sampling plans indexed by acceptance quality limit (AQL) for inspection by variables (known standard deviation) ISO 9073-6, Textiles Test method for nonwovens Part 6: Absorption 3 Terms

26、 and definitions For the purposes of this document, the following terms and definitions apply. 3.1 water resistance of nonwoven materials fabric characteristics which are resistant to wetting and penetration by water 4 Principle This method measures the resistance of fabrics to the penetration of wa

27、ter by impact and can thus be used to predict the probable rain-penetration resistance of the fabric. The sample is used as a protective barrier covering a sheet of pre-weighed absorbent blotting paper. A specific volume of distilled or deionized water is then sprayed onto the sample and the blotter

28、 weighed again. The difference in the two weights is a measure of the amount of water passing through the barrier. The greater the difference, the more water that has passed through, i.e. the less water repellent the fabric. Thus, higher numbers indicate lower water resistance. See Annex A for gener

29、al information on reproducibility. 4 DIN EN ISO 9073-17:2008-09EN ISO 9073-17:2008 (E) 5 Materials and reagents 5.1 Blotting paper2)for spray impact penetration, 150 mm 225 mm, meeting the following parameters: a) no visible distortion in the paper when wetting while testing; b) have an absorbent ra

30、te of 5 s or less (see ISO 9073-6); c) have a minimum absorbent capacity of 480 % (see ISO 9073-6); d) exhibit uniform sheet formation; e) be traceable back to a production lot; f) have a sheet density of (0,24 0,05) g/cm3; g) have a basis weight of (124 6) g/m2; h) have a sheet thickness of 0,500 m

31、m to 0,560 mm at 10 kPa foot pressure. 5.2 Water, distilled, at a temperature of (27 1) C. 5.3 Balance, a laboratory balance capable of weighing the specimen to an accuracy of 0,01 g. 5.4 Stopwatch. 5.5 Baffle, 100 mm 100 mm cut from 6 mm thick polymethyl methacrylate plastic or an equivalent inert

32、material, to be positioned in the funnel to eliminate liquid swirling. 5.6 Drip catcher, e.g. standard blotting paper or any type of absorbent material to catch the last large drops and keep them from hitting the test specimen. 6 Apparatus 6.1 Impact penetration apparatus (impact penetration tester)

33、, as shown in Figure 1 (spray head) and Figure 2 (complete unit minus the weighed clamp). 6.2 Clamp that will clamp across the width of the specimen and which has been modified to provide a total weight of 454 g. 7 Procedure 7.1 Specimens should be sampled in accordance with ISO 3951-5. 7.2 Bring th

34、e specimens and the blotting papers from the prevailing atmosphere to moisture equilibrium for testing in the standard atmosphere as specified in ISO 139. These blotting papers should be exposed to the atmosphere on all sides (hanging on a clothes line is satisfactory). Care in handling should be ob

35、served so that specimens do not contact any contaminants, such as soap, salt, oil, etc., which might facilitate or hinder water penetration. 2) Such paper is available, for example, from Hollingsworth and Vose, Cheltenham, United Kingdom, under the reference ERTFF3. This information is given for the

36、 convenience of users of this part of ISO 9073 and does not constitute an endorsement by ISO of the product. Equivalent products may be used if they can be shown to lead to the same results. 5 EN ISO 9073-17:2008 (E) DIN EN ISO 9073-17:2008-097.3 Specimens should be cut 175 mm 325 mm, with the long

37、dimension in the machine direction. NOTE The accuracy of this procedure is highly depended on the care taken when calibrating the apparatus. 7.4 Weigh a 150 mm 225 mm piece of blotting paper to the nearest 0,01 g and designate this as the initial mass (m1). 7.5 Clamp one end of the test specimen und

38、er the 150 mm spring clamp at the top of the inclined stand. 7.6 Affix a second 150 mm clamp, modified to provide a total mass of 454 g, to the other end of the fabric specimen. 7.7 Position the pre-weighed blotting paper beneath the clamped fabric as shown in Figure 2. 7.8 Pour 500 ml of distilled

39、water, at a temperature of (27 1) C, into the funnel of the tester and allow it to spray onto the test specimen. 7.9 Upon completion of the spraying period, and at the proper time (2 s after the continuous flow stops), insert the “drip catcher” blotting paper to stop the remaining water from hitting

40、 the test area. 7.10 Lift the test specimen carefully and remove the blotting paper beneath it. 7.11 In order not to allow any evaporation loss, immediately weigh the blotting paper to the nearest 0,01 g (m2). 8 Calculation The increase in mass from m1to m2of the blotters is calculated in grams, and

41、 the individual, average and standard deviation results for each test sample are reported. 9 Test report The test report shall include the following: a) a reference to this part of ISO 9073, i.e. ISO 9073-17; b) type or designation of material tested; c) number of test pieces tested; d) testing cond

42、itions; e) individual spray impact, expressed in grams, to an accuracy of 0,01 g; f) the average and standard deviation of the spray impact, expressed in grams; g) any deviation from the standard procedure. 6 DIN EN ISO 9073-17:2008-09EN ISO 9073-17:2008 (E) Dimensions in millimetres Key 1 25 holes,

43、 61 drill 2 brass 3 bronze Figure 1 Spray head or nozzle for impact penetration tester 7 EN ISO 9073-17:2008 (E) DIN EN ISO 9073-17:2008-09Dimensions in millimetres Key 1 funnel 2 extension ring 3 ferrule 4 slide assembly 5 valve 6 spray head 7 clamp 8 drip catcher 9 test stand 10 spring clip 11 spe

44、cimen and blotting paper on clipboard 12 baffle Figure 2 Impact penetration tester 8 DIN EN ISO 9073-17:2008-09EN ISO 9073-17:2008 (E) Annex A (informative) General information regarding reproducibility This interlaboratory study was based on using six laboratories, 30 specimens of one material and

45、two types of blotting paper. The two blotting papers were type A, blotting paper that met all the test-procedure parameters, and type B blotting paper that was supplied as “routine” but did not meet any of the test-procedure requirements. It was more dense, more variable, had a slow absorbent rate a

46、nd distorted greatly when wet. Table A.1 illustrates what the six laboratories found and how the two blotting papers compared. All the observations are taken by well-trained operators using specimens randomly tested from one lot of standard material specification (SMS) material. This procedure requi

47、res the use of a blotting paper with very tight control standards, as stated in 5.1. Table A.1 Comparison between two blotting papers Blotting-paper sample A Blotting-paper sample B No. of participating laboratories 6 6 No. of non-eliminated laboratories 6 6 No. of single values at each of the non-e

48、liminated laboratories 30 30 Grand average 0,522 4,319 Standard deviation of repeatability, sr0,607 2,592 Standard deviation of reproducibility, sR0,607 2,726 One population of SMS material was used for all testing. A blotting paper that has a low absorbent rate and a high density will distort and give unreliable results. 9 EN ISO 9073-17:2008 (E) DIN EN ISO 9073-17:2008-09