DIN EN 16433-2014 Internal blinds - Protection from strangulation hazards - Test methods German version EN 16433 2014《内部窗帘 防止勒束危险的保护 试验方法 德文版本EN 16433-2014》.pdf

《DIN EN 16433-2014 Internal blinds - Protection from strangulation hazards - Test methods German version EN 16433 2014《内部窗帘 防止勒束危险的保护 试验方法 德文版本EN 16433-2014》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 16433-2014 Internal blinds - Protection from strangulation hazards - Test methods German version EN 16433 2014《内部窗帘 防止勒束危险的保护 试验方法 德文版本EN 16433-2014》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、June 2014 Translation by DIN-Sprachendienst.English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 9

2、1.060.50!%2b“2156397www.din.deDDIN EN 16433Internal blinds Protection from strangulation hazards Test methods;English version EN 16433:2014,English translation of DIN EN 16433:2014-06Innere Abschlsse Schutz vor Strangulationsgefahren Prfverfahren;Englische Fassung EN 16433:2014,Englische bersetzung

3、von DIN EN 16433:2014-06Stores intrieurs Protection contre les risques de strangulation Mthodes dessai;Version anglaise EN 16433:2014,Traduction anglaise de DIN EN 16433:2014-06www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 20 pages 05

4、.14 DIN EN 16433:2014-06 2 A comma is used as the decimal marker. National foreword This document (EN 16433:2014) has been prepared by Technical Committee CEN/TC 33 “Doors, windows, shutters, building hardware and curtain walling” (Secretariat: AFNOR, France). The responsible German body involved in

5、 its preparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Working Committee NA 005-09-01 AA Tren, Tore, Fenster, Abschlsse, Baubeschlge und Vorhangfassaden. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16433 February 2014 ICS 91.060.50 English Ve

6、rsion Internal blinds - Protection from strangulation hazards - Test methods Stores intrieurs - Protection contre les risques de strangulation - Mthodes dessai Innere Abschlsse - Schutz vor Strangulationsgefahren - Prfverfahren This European Standard was approved by CEN on 26 October 2013. CEN membe

7、rs are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on applicatio

8、n to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Manageme

9、nt Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, L

10、ithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17

11、, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16433:2014 EEN 16433:2014 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 General 5 5 Test sample 7 6 Breakaway s

12、ystem .7 6.1 General 7 6.2 Test method .7 7 Tensioning system . 10 7.1 General . 10 7.2 Test method 11 8 Accumulation system . 12 8.1 General . 12 8.2 Test method 12 9 Tangling test 13 9.1 General . 13 9.2 Test method 13 10 Inner cords test . 13 10.1 General . 13 10.2 Test method 14 Annex A (informa

13、tive) Flowchart of testing . 17 Bibliography . 18 DINEN 16433:2014-06EN 16433:2014 (E) 3 Foreword This document (EN 16433:2014) has been prepared by Technical Committee CEN/TC 33 “Doors, windows, shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR. This Europe

14、an Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2014, and conflicting national standards shall be withdrawn at the latest by August 2014. Attention is drawn to the possibility that some of the element

15、s of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. This document is pa

16、rt of a series of standards dealing with blinds and shutters for buildings as defined in EN 12216. It is the intention that safety devices used in EN 13120 conform to EN 16434 for component testing and EN 16433 for functionality. According to the CEN-CENELEC Internal Regulations, the national standa

17、rds organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Lux

18、embourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DINEN 16433:2014-06EN 16433:2014 (E) 4 1 Scope This European Standard specifies test methods for the verification of the requirements relating to the protect

19、ion from strangulation. This European Standard applies to all internal blinds as specified in EN 13120, insect screens as specified in EN 13561 and to blinds in sealed glazed units. These products may be operated manually, with or without compensating springs, or by means of electric motors (power o

20、perated products). Although at the time this standard has been published, no product standard exists for draperies, test methods specified in the present standard may be used for such products. 2 Normative references The following documents, in whole or in part, are normatively referenced in this do

21、cument and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12216, Shutters, external blinds, internal blinds - Terminology, glossary and definitio

22、ns EN 13120, Internal blinds - Performance requirements including safety EN 13561, External blinds and awnings - Performance requirements including safety 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12216, EN 13120 and EN 13561 and the following a

23、pply. 3.1 head probe test probe representing the head of a child Note 1 to entry: See Figure 2. 3.2 accessibility probe test probe representing a finger of a child Note 1 to entry: See Figure 3. 3.3 length of pull cord(s), chain(s), ball-chain(s), tape(s) and similar distance from the highest point

24、of the internal blind to the bottom of the loop of a cord, chain, ball-chain, tape and similar Note 1 to entry: See Figure 1. DIN EN 16433:2014-06 EN 16433:2014 (E) 5 Key 1 length of pull cord(s), chain(s), ball-chain(s), tape(s) and similar Figure 1 Illustration of the length of the pull cord(s), c

25、hain(s), ball-chain(s), tape(s) and similar 4 General All tests defined in this standard shall be performed at 23 C 5 C. All dimensions, masses and forces shall be considered with a maximum tolerance of 1 %. Although all figures show free-hanging loads to apply forces, other methods of achieving the

26、 same effect may be used. Unless otherwise specified, a pulley of 20 mm diameter shall be used to apply the loads. Annex A presents a flowchart summarizing tests to be carried out on internal blinds. The internal blinds shall be installed according to the manufacturer specification so that the insta

27、llation, i.e. the test rig, the fixing, etc., has no influence on the results of tests. In the context of this standard, the term “cord(s)” used shall mean “cord(s), chain(s), ball-chain(s), tape(s) and similar”. The head probe shall have the dimensions and design specified in Figure 2. It shall be

28、made of a rigid material and shall have a smooth finish. NOTE This probe is taken from ANSI/WCMA A100.12010 and is equivalent to the small head probe defined in CEN/TR 13387:2004 (Table 3.3B) for children aged from 9 to 12 months. DIN EN 16433:2014-06 EN 16433:2014 (E) 6 Figure 2 Head probe dimensio

29、ns The accessibility probe shall be of the dimensions and design specified in Figure 3. Figure 3 Accessibility probe DIN EN 16433:2014-06 EN 16433:2014 (E) 7 5 Test sample A test sample shall be representative of a family of products which may cover a variety of dimensions or weight of internal blin

30、ds. In the context of this standard, a family of products is defined with regard to the utilization of common safety device(s) and any design aspect relating to protection from strangulation. Within a family, the test sample shall be chosen so that the following conditions are fulfilled: Tensioning

31、systems: this test shall be carried out on an internal blind with the maximum length of the operating cord(s). Breakaway systems: the tests shall be carried out on an internal blind taking into account the maximum number of pull cord(s). Accumulation systems: the tests shall be carried out on an int

32、ernal blind taking into account the maximum length and number of pull cord(s) when the curtain is retracted. Inner cord(s): the tests shall be carried out on an internal blind taking into account the maximum distance between two consecutive points of attachment / retention. Within a family of produc

33、ts, there is no variation in the design of the internal blind that would affect the tangling test. 6 Breakaway system 6.1 General For the tests defined in 6.2 a test cylinder of 60 mm diameter made of a rigid material shall be inserted into the loop. The total mass specified in EN 13120 shall be gra

34、dually applied downwards. This mass shall include the mass of the cylinder. “Gradually” means there shall be no dynamic effect on the cord. NOTE The test cylinder is intended to represent the neck of a child. 6.2 Test method 6.2.1 Operating system consisting of a pull cord(s) forming a hazardous loo

35、p The length of the pull cord(s) shall be measured. The test shall be carried out on the breakaway system so that a breakaway device is successively located at the highest possible position, at the lowest position (at the bottom of the loop) and in the middle of the loop (see Figure 4). After a succ

36、essful breakaway test, the affected device shall be replaced. If several breakaway devices are used, they all shall be tested in the positions mentioned above. DINEN 16433:2014-06EN 16433:2014 (E) 8 Key 1 looped pull cord 2 test cylinder 3 load 4 breakaway device Figure 4 Illustration of the test of

37、 a breakaway system on a looped cord (example of a single breakaway device) If the performance of the breakaway system is independent of the position of any specific component (e.g. a breakaway device), the test shall be carried out with the loop in any position. 6.2.2 Operating system consisting of

38、 free hanging pull cord(s) connected together The length of the pull cord(s) shall be measured. The internal blind shall be placed in the fully retracted position (see Figure 5). If more than two cords are connected together, all possible loop combinations shall be tested. DIN EN 16433:2014-06 EN 16

39、433:2014 (E) 9 Key 1 looped pull cord 2 headrail 3 test cylinder 4 load 5 breakaway system Figure 5 Illustration of the test of a breakaway system on hanging pull cords connected together (example of two cords) 6.2.3 Inner cord(s) forming a hazardous loop The test shall be carried out on the penulti

40、mate and the last panel with the internal blind in the fully extended position (see Figure 6). DINEN 16433:2014-06EN 16433:2014 (E) 10 Key 1 inner cord 2 headrail 3 curtain 4 test cylinder 5 load Figure 6 Illustration of the test of a breakaway system on an inner cord (example when a loop is created

41、 with the curtain) 7 Tensioning system 7.1 General This subclause applies to internal blinds where the operating system consists of a continuous cord(s) forming a loop and maintained under tension by a system secured to a fixed surface (e.g. window frame, wall, .). It shall be verified that the tens

42、ioning system consisting of the pull cord(s), the control mechanism: the pulley and its housing, and the fixed retaining device maintaining the cord(s) under tension, shall not break under the application of a horizontal load applied in the middle of the cord(s) (see Figure 7). Where a tensioning sy

43、stem is designed to accept more than one cord, each cord shall be tested separately. DINEN 16433:2014-06EN 16433:2014 (E) 11 Key 1 pull cord(s) 2 control mechanism 3 fixed retaining device Figure 7 Principle of the test of tensioning system 7.2 Test method All installation positions described in the

44、 installation instructions of the manufacturer shall be tested. The distance between the two strands of the loop shall be measured at the point of exit from the fixed tensioning system (see Figure 8). DINEN 16433:2014-06EN16433:2014(E)12 Key 1 distance between the two strands Figure 8 Measurement of

45、 the distance between the two strands The length of the pull cord(s) shall be measured. A horizontal force shall be gradually applied in the plane and at mid-point of the height of the loop (see Figure 7) until the load defined in EN 13120 is applied to the cord. Gradually means there shall be no dy

46、namic effect on the cord. The load shall be then maintained for 10 s. The test shall be repeated with the force being applied in the direction perpendicular to the plane of the cord. 8 Accumulation system 8.1 General This subclause applies to internal blinds for which extension and retraction of the

47、 curtain leads to a change in length of the pull cord(s). It shall be verified that the full length of pull cord(s) can be accumulated at any position of the curtain, including fully retracted. 8.2 Test method The length of the pull cord(s) shall be measured when the internal blind is in the fully e

48、xtended position. The pull cord(s) shall be accumulated according to the instructions of the manufacturer when the internal blind is in the fully retracted position. DIN EN 16433:2014-06 EN 16433:2014 (E) 13 9 Tangling test 9.1 General This subclause applies to internal blinds where the operating system consists of two free hanging pull cords. In this situation, it shall be verified that the two cords present cannot tangle producing a hazardous loop. 9.2 Test method One cord shall be twisted around the ot