DIN EN 650-2012 Resilient floor coverings - Polyvinyl chloride floor coverings on jute backing or on polyester felt backing or on a polyester felt with polyvinyl chloride backing -.pdf

《DIN EN 650-2012 Resilient floor coverings - Polyvinyl chloride floor coverings on jute backing or on polyester felt backing or on a polyester felt with polyvinyl chloride backing -.pdf》由会员分享，可在线阅读，更多相关《DIN EN 650-2012 Resilient floor coverings - Polyvinyl chloride floor coverings on jute backing or on polyester felt backing or on a polyester felt with polyvinyl chloride backing -.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、December 2012 Translation by DIN-Sprachendienst.English price group 9No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 97.150!$V“1929051www.din.deDDIN EN 650Resilient floor coverings Polyvinyl chloride floor coverings on jute backing or on polyester feltbacking or on a polyester felt with polyvinyl chloride backing Specification;English version EN 650:2012,English translation of DIN EN 650:2012-12Elastische Bodenb

3、elge Bodenbelge aus Polyvinylchlorid mit einem Rcken aus Jute oder Polyestervlies oder aufPolyestervlies mit einem Rcken aus Polyvinylchlorid Spezifikation;Englische Fassung EN 650:2012,Englische bersetzung von DIN EN 650:2012-12Revtements de sol rsilients Revtements de sol base de polychlorure de v

4、inyle sur support de jute ou de polyesteravec envers en polychlorure de vinyle Spcification;Version anglaise EN 650:2012,Traduction anglaise de DIN EN 650:2012-12SupersedesDIN EN 650:1997-01www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authori

5、tative.1511.12 DIN EN 650:2012-12 2 A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings” (Secretariat: BSI, United Kingdom). The responsible German body involved in its preparation

6、 was the Normenausschuss Kunststoffe (Plastics Standards Committee), Working Committee NA 054-04-05 AA Bodenbelge. Amendments This standard differs from DIN EN 650:1997-01 as follows: a) normative references have been updated; b) the characteristic “thickness loss” has been deleted from Table 2 “Cla

7、ssification requirements for wear groups”; c) Subclause 4.2.2 “Wear layers” has been included; d) the previous Table 3 “Classification requirements for level of use” has been split into new Tables 3 and 4; e) a new class “22” has been included in Table 4 “Classification requirements for level of use

8、”; f) the designation of the level of use (Tables 3 and 4) has been brought in line with DIN EN 685; g) Annexes A and B have been merged in Annex A “Optional properties” and further test methods have been included for: Resistance to stubbed and burning cigarettes (EN 1399); Curling on exposure to mo

9、isture (EN 662); h) the Bibliography has been updated; i) the standard has been editorially revised. Previous editions DIN EN 650: 1997-01 DIN 16952-1: 1972-02, 1977-04 DIN 16952-4: 1977-04 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 650 September 2012 ICS 97.150 Supersedes EN 650:1996Engli

10、sh Version Resilient floor coverings - Polyvinyl chloride floor coverings on jute backing or on polyester felt backing or on a polyester felt with a polyvinyl chloride backing - Specification Revtements de sol rsilients - Revtements de sol base de polychlorure de vinyle sur support de jute ou de pol

11、yester avec envers en polychlorure de vinyle - Spcifications Elastische Bodenbelge - Bodenbelge aus Polyvinylchlorid mit einem Rcken aus Jute oder Polyestervlies oder auf Polyestervlies mit einem Rcken aus Polyvinylchlorid - Spezifikation This European Standard was approved by CEN on 10 August 2012.

12、 CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on

13、application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELE

14、C Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,

15、 Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17,

16、B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 650:2012: EEN 650:2012 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .54 Requirements and testing .54.1 General requireme

17、nts 54.2 Classification requirements 54.2.1 Wear group classification .54.2.2 Homogeneous products and wear layers .54.2.3 Level of use classification 55 Marking 11Annex A (informative) Optional properties 12Bibliography . 13DIN EN 650:2012-12 EN 650:2012 (E) 3 Foreword This document (EN 650:2012) h

18、as been prepared by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March

19、 2013, and conflicting national standards shall be withdrawn at the latest by March 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent righ

20、ts. This document supersedes EN 650:1996. The following technical changes were introduced in this version: Wear group classification is based on one method (EN 660-2) instead of two (EN 660-1 and -2) A requirement on “wear layers“ has been added A new table 3 was included. The original table 3 is no

21、w table 4. Annexes A and B were merged and new characteristics added (staining, cigarette resistance, curling when wet) According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium,

22、Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland

23、, Turkey and the United Kingdom. DIN EN 650:2012-12 EN 650:2012 (E) 4 1 Scope This European Standard specifies the characteristics of floor coverings based on polyvinyl chloride and modifications thereof, on jute or polyester backing or on polyester felt with polyvinyl chloride backing, supplied in

24、either tile or roll form. To encourage the consumer to make an informed choice the standard includes a classification system (see EN 685) based on intensity of use, which shows where these floor coverings should give satisfactory service. It also specifies requirements for marking. 2 Normative refer

25、ences The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. E

26、N 424, Resilient floor coverings Determination of the effect of simulated movement of a furniture leg EN 425, Resilient and laminate floor coverings Castor chair test EN 426, Resilient floor coverings Determination of width, length, straightness and flatness of sheet material EN 427, Resilient floor

27、 coverings Determination of the side length, squareness and straightness of tiles EN 428, Resilient floor coverings Determination of overall thickness EN 429, Resilient floor coverings Determination of the thickness of layers EN 430, Resilient floor coverings Determination of mass per unit area EN 4

28、31, Resilient floor coverings Determination of peel resistance EN 432, Resilient floor coverings Determination of shear force EN 433, Resilient floor coverings Determination of residual indentation after static loading EN 434, Resilient floor coverings Determination of dimensional stability and curl

29、ing after exposure to heat EN 436, Resilient floor coverings Determination of density EN 660-2, Resilient floor coverings Determination of wear resistance Part 2: Frick-Taber test EN 661, Resilient floor coverings Determination of the spreading of water EN 663, Resilient floor coverings Determinatio

30、n of conventional pattern depth EN 684, Resilient floor coverings Determination of seam strength EN 685, Resilient, textile and laminate floor coverings Classification EN 718, Resilient floor coverings Determination of mass per unit area of a reinforcement or a backing of polyvinyl chloride floor co

31、verings EN ISO 105-B02:1999, Textiles Tests for colour fastness Part B02: Colour fastness to artificial light: Xenon arc fading lamp test (ISO 105-B02:1994, including amendment 1:1998) DIN EN 650:2012-12 EN 650:2012 (E) 5 3 Terms and definitions For the purposes of this document, the following terms

32、 and definitions apply. 3.1 polyvinyl chloride floor covering on jute backing floor covering consisting of a polyvinyl chloride surface layer applied to jute felt backing 3.2 polyvinyl chloride floor covering on polyester felt backing floor covering consisting of a polyvinyl chloride surface layer a

33、pplied to polyester felt backing 3.3 polyvinyl chloride floor covering on polyester felt with polyvinyl chloride backing floor covering consisting of a polyvinyl chloride surface layer applied to polyester felt with a polyvinyl chloride backing 4 Requirements and testing 4.1 General requirements Flo

34、or coverings described in this European Standard shall conform to the appropriate general requirements as specified in Table 1 when tested in accordance with the methods given therein. 4.2 Classification requirements 4.2.1 Wear group classification Polyvinyl chloride floor coverings are classified i

35、n the appropriate wear group specified in EN 660-2. Floor coverings described in this standard shall be classified in wear group T or P. Floor coverings with a transparent wear layer are a priori group T and need not be tested 4.2.2 Wear layers A homogeneous product shall retain its wear group class

36、ification throughout the thickness of the product if tested. A wear layer shall retain its wear group classification throughout its thickness if tested. 4.2.3 Level of use classification Floor coverings described in this European Standard shall be classified as suitable for different levels of use i

37、n accordance with the performance requirements specified in Table 3 and 4, when tested with the methods given therein. Classification shall conform to the scheme specified in EN 685. DIN EN 650:2012-12 EN 650:2012 (E) 6 Table 1 General requirements (1 of 2) Characteristic Requirement Test method Rol

38、l form: length m width mm Not less than the nominal values EN 426 Tiles: side length mm squareness and straightness for side length: mm 400 mm 400 mm 400 mm (intended for welding) Deviation 0,13 % of nominal length up to 0,5 mm maximum Deviation allowed at any point 0,25 0,35 0,50 EN 427 Overall thi

39、ckness: mm average individual results Nominal value + 0,18 - 0,15 Average value 0,20 EN 428 Total mass per unit area g/m Nominal value + 13 % average - 10% EN 430 Mass per unit area of backing g/m Jute backing: average individual results Polyester backing average individual results 500 400 300 270 E

40、N 718 Density of the wear layer (average) kg/m Nominal value 0,50 EN 436 Dimensional stability after exposure % to heat: Floor coverings on jute or polyester felt backing Floor coverings on polyester felt with polyvinyl chloride backing sheets and tiles intended for welding tiles intended for dry-jo

41、int laying 0,4 0,4 0,25 EN 434 DIN EN 650:2012-12 EN 650:2012 (E) 7 Table 1 (2 of 2) Curling after exposure to heat: mm Floor coverings on jute or polyester felt Floor coverings on polyester felt with polyvinyl chloride backing: sheets and tiles intended for welding tiles intended for dry-joint layi

42、ng 8 8 2 EN 434 Colour fastness to artificial light 6 minimum EN ISO 105-B02:1999 Method 3 aPeel resistance N/50 mm average individual results 50 40 EN 431 Shear force of backing (for jute backing only) average individual results 360 280 EN 432 Spreading of water bThe time for water to spread to one

43、 edge of a test specimen shall be greater than 16 h EN 661 aExpose a full size of test specimen. Store a further test specimen in the dark, which will constitute the reference standard for assessment of colour change. bFor floor coverings, other than those on jute backing, intended for use under moi

44、st conditions. Table 2 Classification requirements for wear groups Characteristic Requirements for wear group Test method T P M F volume loss Fv mm Fv 2,0 a2,0 Fv 4,0 4,0 Fv 7,5 7,5 Fv 15,0 EN 660-2 aIf tested for verification. DIN EN 650:2012-12 EN 650:2012 (E) 8 Table 3 Classification requirements

45、 for level of use (1 of 2) Class Symbol dLevel of use Thickness of wear layer. Nominal value c, mm Conventional pattern of depth. Nominal value (minimum), mm Effect of castor chair Simulated movement of a furniture leg Seam strength when welded in accordance with manufacturers instructions N/50 mm T

46、 P TP 21 domestic moderate 0,15 0,20 0,13 0,15 No requirement No requirement No requirement 22 domestic general 0,20 0,30 0,15 0,18 No damage shall be visible after testing with a type 3 foot 22+ domestic general 0,20 0,30 0,15 0,18 23 domestic heavy 0,25 0,40 0,18 0,20 31 commercial moderate 0,25 0

47、,40 0,18 0,20 32 abcommercial general 0,35 0,50 0,30 - No disturbance to the surface other than slight change inappearance and no delamination shall occur No damage shall be visible after testing with a type 2 foot Average value 150 Individual values 120 DIN EN 650:2012-12 EN 650:2012 (E) 9 Table 3 (2 of 2) 41 blight industrial moderate 0,35 0,50 0,30 - No disturbance to the surface other than slight change inappearance and no delamination shall occur No damage shall be visible after testing wi