DIN EN 1559-5-2017 Founding - Technical conditions of delivery - Part 5 Additional requirements for magnesium alloy castings German version EN 1559-5 2017《铸造 交货技术条件 第5部分 镁合金铸件的附加要求.pdf

《DIN EN 1559-5-2017 Founding - Technical conditions of delivery - Part 5 Additional requirements for magnesium alloy castings German version EN 1559-5 2017《铸造 交货技术条件 第5部分 镁合金铸件的附加要求.pdf》由会员分享，可在线阅读，更多相关《DIN EN 1559-5-2017 Founding - Technical conditions of delivery - Part 5 Additional requirements for magnesium alloy castings German version EN 1559-5 2017《铸造 交货技术条件 第5部分 镁合金铸件的附加要求.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、May 2017 English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 77.150.20!%dq“2659678www.din.deDIN EN

2、 1559-5Founding Technical conditions of delivery Part 5: Additional requirements for magnesium alloy castings;English version EN 15595:2017,English translation of DIN EN 1559-5:2017-05Gieereiwesen Technische Lieferbedingungen Teil 5: Zustzliche Anforderungen an Gussstcke aus Magnesiumlegierungen;Eng

3、lische Fassung EN 15595:2017,Englische bersetzung von DIN EN 1559-5:2017-05Fonderie Conditions techniques de fourniture Partie 5: Spcifications complmentaires pour les pices moules en alliages de magnsium;Version anglaise EN 15595:2017,Traduction anglaise de DIN EN 1559-5:2017-05SupersedesDIN EN 155

4、95:199801www.beuth.deDocument comprises 12 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.04.17 DIN EN 1559-5:2017-05 2 A comma is used as the decimal marker. National foreword This document (EN 1559-5:2017) has been prepared

5、by Technical Committee CEN/TC 190 “Foundry technology” (Secretariat: DIN, Germany). The responsible German bodies involved in its preparation were DIN-Normenausschuss Gieereiwesen (DIN Standards Committee Foundry Technology) and DIN-Normenausschuss Nichteisenmetalle (DIN Standards Committee Nonferro

6、us Metals), Working Committee NA 036-00-02 GA “Joint working committee Foundry Practice Standards/Nonferrous Metals Standards: Cast magnesium”. Amendments This standard differs from DIN EN 1559-5:1998-01 as follows: a) Clause 4 has been extended; b) Clause 5: Table 1 has been included; c) Subclause

7、7.3.3.1: Table 2 has been included; d) Subclauses 7.3.3.3 and 7.3.3.4 have been extended; e) Annex A has been included; f) the standard has been brought in line with EN 1559-1:2011. Previous editions DIN EN 1559-5: 1998-01 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1559-5 March 2017 ICS 77

8、.150.20 Supersedes EN 1559-5:1997English Version Founding - Technical conditions of delivery - Part 5: Additional requirements for magnesium alloy castings Fonderie - Conditions techniques de fourniture - Partie 5 : Spcifications complmentaires pour les pices moules en alliages de magnsium Gieereiwe

9、sen - Technische Lieferbedingungen - Teil 5: Zustzliche Anforderungen an Gussstcke aus Magnesiumlegierungen This European Standard was approved by CEN on 6 January 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European

10、Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (En

11、glish, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium

12、, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, S

13、witzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN nat

14、ional Members. Ref. No. EN 1559-5:2017 EEN 1559-5:2017 (E) 2 Contents Page European foreword . 3 Introduction 4 1 Scope 5 2 Normative references 5 3 Terms and definitions 5 4 Information to be supplied by the purchaser . 6 5 Designations 6 6 Manufacture 7 7 Requirements . 7 8 Inspection 8 9 Marking

15、. 9 10 Packaging and surface protection . 9 11 Complaints . 9 Annex A (informative) Significant technical changes between this European standard and the previous edition 10 DIN EN 1559-5:2017-05 EN 1559-5:2017 (E) 3 European foreword This document (EN 1559-5:2017) has been prepared by Technical Comm

16、ittee CEN/TC 190 “Foundry Technology”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2017, and conflicting national standards shall be withdraw

17、n at the latest by September 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1559-5:1997. Within its programme of w

18、ork, Technical Committee CEN/TC 190 requested CEN/TC 190/WG 9 “Cast Magnesium” to revise the following standard: EN 1559-5:1997, Founding Technical conditions of delivery Part 5: Additional requirements for magnesium alloy castings Annex A provides details of significant technical changes between th

19、is European Standard and the previous edition. This standard is one of a series of European Standards for technical delivery conditions for castings. The other standards in this series are: EN 1559-1, Founding Technical conditions of delivery Part 1: General EN 1559-2, Founding Technical conditions

20、of delivery Part 2: Additional requirements for steel castings EN 1559-3, Founding Technical conditions of delivery Part 3: Additional requirements for iron castings EN 1559-4, Founding Technical conditions of delivery Part 4: Additional requirements for aluminium alloy castings EN 1559-6, Founding

21、Technical conditions of delivery Part 6: Additional requirements for zinc alloy castings According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czec

22、h Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United

23、 Kingdom. DIN EN 1559-5:2017-05 EN 1559-5:2017 (E) 4 Introduction CEN/TC 190 “Foundry Technology” has prepared material standards covering magnesium alloy castings. In order to assist manufacturers and purchasers to prepare proper contractual arrangements and prevent misunderstanding, CEN/TC 190 app

24、roved the preparation of a series of standards covering technical delivery conditions. These have been prepared as separate parts. This part of EN 1559 covers the additional technical delivery conditions for magnesium alloy castings, e.g. optional information, manufacturing process, additional requi

25、rements regarding the condition of the casting and test methods. This part of EN 1559 cannot be used alone for compiling a specification for ordering and supplying magnesium alloy castings, but as a complement to EN 1559-1. The clauses marked with a single dot indicate that the requirements of the s

26、ame clauses of EN 1559-1 have to be met. DIN EN 1559-5:2017-05 EN 1559-5:2017 (E) 5 1 Scope This part of EN 1559 specifies the additional technical delivery conditions for castings (see EN 1753) and cast anodes (see EN 12438) made from magnesium alloys. This part of EN 1559 applies to magnesium allo

27、y castings produced in sand or permanent moulds or by pressure die casting, centrifugal casting, continuous casting or investment casting. This part of EN 1559 does not apply to ingots, bars, billets (or other shapes) for further reprocessing, such as re-melting or extrusion. 2 Normative references

28、The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1370

29、, Founding - Examination of surface condition EN 1371-1, Founding - Liquid penetrant testing- Part 1: Sand, gravity die and low pressure die castings EN 1371-2, Founding - Liquid penetrant testing - Part 2: Investment castings EN 1559-1:2011, Founding - Technical conditions of delivery - Part 1: Gen

30、eral EN 1753, Magnesium and magnesium alloys - Magnesium alloy ingots and castings EN 1754, Magnesium and magnesium alloys - Designation system for anodes, ingots and castings - Material symbols and material numbers EN 12438, Magnesium and magnesium alloys - Magnesium alloys for cast anodes prEN 126

31、81-1, Founding - Radiographic testing - Part 1: Film techniques1prEN 12681-2, Founding - Radiographic testing - Part 2: Techniques with digital detectors2EN ISO 3452-1, Non-destructive testing - Penetrant testing - Part 1: General principles (ISO 3452-1) EN ISO 5579, Non-destructive testing - Radiog

32、raphic testing of metallic materials using film and X- or gamma rays - Basic rules (ISO 5579) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 1559-1 and in the applicable material standard apply. 1) In development. 2) In development. DIN EN 1559-5:201

33、7-05 EN 1559-5:2017 (E) 6 4 Information to be supplied by the purchaser 4.1 Mandatory information 4.2 Optional information Where applicable, the enquiry and order shall include other details, such as requirements for: a) an as-cast condition; b) special or subsequent heat treatment if required (toge

34、ther with the heat-treatment conditions); c) formation of test units (unless already defined by material specifications, it shall be in accordance with 8.3.1). 4.3 Drawings, patterns and tools 4.4 Information on the mass 4.5 Preliminary sample 4.6 Initial sample 5 Designations The designation of cas

35、t magnesium alloys by material number or material symbol shall be in accordance with EN 1754. Both designations describe the magnesium alloys according to their chemical composition. The designation shall be used on the drawings and in the order. To identify the temper (heat treatment condition) and

36、/or the casting process, the designation shall be supplemented with symbols preceded and separated from each other by a hyphen (-): for tempers as given in EN 1753; for casting processes as given in EN 1753 and EN 12438. For examples of the use of these symbols in conjunction with either the materia

37、l symbol or material number see Table 1. Table 1 Examples for the designation Designation by Explanation for the supplement number symbol 3.5316 EN-MCMgAl9Zn1(A) without supplement 3.5316-T4 EN-MCMgAl9Zn1(A)-T4 “-T4” specifies the temper (heat treatment condition) 3.5316-F-D EN-MCMgAl9Zn1(A)-F-D “-F

38、-D” specifies the temper and the casting process 3.5130 EN-MAMgMn1 without supplement 3.5130-S EN-MAMgMn1-S “-S” specifies the casting process DIN EN 1559-5:2017-05 EN 1559-5:2017 (E) 7 6 Manufacture 6.1 Manufacturing process 7 Requirements 7.1 General 7.2 Material 7.2.1 Chemical composition EN 1559

39、-1 shall apply with the following addition: Determination of elements not specified in the applicable material standard shall be carried out when agreed between the manufacturer and the purchaser by the time of acceptance of the order. 7.2.2 Mechanical properties 7.2.3 Other properties 7.3 Casting 7

40、.3.1 Chemical composition 7.3.2 Mechanical properties 7.3.3 Outer and inner conditions (non-destructive testing) 7.3.3.1 The testing shall be performed according to the applicable European Standards as listed in Table 2. Other methods may be agreed between purchaser and manufacturer. Table 2 Test me

41、thods Test method Symbol General principles Test conditions Liquid penetrant PT EN ISO 3452-1 EN 13711 EN 13712 Radiographic RT EN ISO 5579 prEN 126811 prEN 126812 7.3.3.2 7.3.3.3 The selection of a non-destructive testing method is dependent on the thickness and material of the casting and the posi

42、tion, orientation and size of possible discontinuities in the areas to be tested. Different acceptance criteria can be specified for different areas of the same casting. Moreover, for the same area of the casting different acceptance criteria can be specified according to the non-destructive test me

43、thods selected. For all non-destructive testing methods, the acceptance criteria (discontinuity levels) can be graded with increasing number and/or extent of indications. Unless specifically agreed, discontinuities revealed on cast surfaces which are to be machined, are not to be regarded as discont

44、inuities, when these discontinuities are totally removed by machining. DIN EN 1559-5:2017-05 EN 1559-5:2017 (E) 8 7.3.3.4 If applicable, the roughness of the cast or grinded surface shall be specified in accordance with EN 1370 and shall be subject of an agreement between the manufacturer and the pu

45、rchaser by the time of acceptance of the order. 7.3.4 Condition of the casting 7.3.5 Mass of the casting 7.3.6 Additional requirements regarding the condition of the casting 7.3.6.1 In order to eliminate leaks in castings, impregnation procedures may be used after the approval of the purchaser. The

46、impregnation medium and method, maximum permitted size of discontinuities and retest procedures shall be agreed between the manufacturer and the purchaser. 7.3.6.2 Where appropriate, a macroscopic examination of a suitably prepared section shall be carried out to assess the grain structure and/or st

47、ructural inadequacy of a casting to agreed criteria. NOTE Assessment is usually carried out with naked eyes or with an agreed magnification. 7.3.6.3 Where appropriate, a microscopic examination of a suitably prepared section shall be carried out to determine the metallurgical structure of a casting

48、to agreed criteria. NOTE 1 Assessment is usually carried out with an agreed magnification and can include the nature, shape and distribution of the structural constituents. NOTE 2 A cooling curve/thermal analysis carried out on a sample of liquid alloy before casting can help to predict the metallur

49、gical structure of the casting. 7.3.6.4 If applicable, density evaluation by weighting in air and water to agreed criteria shall be used to estimate the soundness of the casting. 8 Inspection 8.1 General 8.2 Type of inspection documents and type of inspection The requirements given in the applicable material standard shall also apply. 8.3 Test unit 8.3.1 Formation of test units 8