DIN EN 15272-2-2007 Inland navigation vessels - Equipment for rope leading - Part 2 Fairlead English version of DIN EN 15272-2 2007-06《内河航行船舶 绳索导向设备 第2部分 导缆器》.pdf

《DIN EN 15272-2-2007 Inland navigation vessels - Equipment for rope leading - Part 2 Fairlead English version of DIN EN 15272-2 2007-06《内河航行船舶 绳索导向设备 第2部分 导缆器》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 15272-2-2007 Inland navigation vessels - Equipment for rope leading - Part 2 Fairlead English version of DIN EN 15272-2 2007-06《内河航行船舶 绳索导向设备 第2部分 导缆器》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、June 2007DEUTSCHE NORM English price group 10No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 47.020.50; 47.060!,yZ“986

2、2955www.din.deDDIN EN 15272-2Inland navigation vessels Equipment for rope leading Part 2: FairleadEnglish version of DIN EN 15272-2:2007-06Fahrzeuge der Binnenschifffahrt Ausrstung zur Seilfhrung Teil 2: UmlenkrolleEnglische Fassung DIN EN 15272-2:2007-06www.beuth.deDocument comprises 18 pages 09.07

3、DIN EN 15272-2:2007-06 2 Start of validity This standard is valid from 1 June 2007. National foreword This standard includes safety requirements. This standard has been prepared by CEN/TC 15 “Inland navigation vessels” (Secretariat: DIN, Germany). The responsible German body involved in its preparat

4、ion was the Normenstelle Schiffs- und Meerestechnik (Shipbuilding and Marine Technology Standards Committee), Joint Committee BWH/NSMT NA 132-07-01 AA. The DIN Standard corresponding to the International Standard referred to in clause 2 of the EN is as follows: ISO 2768-1 DIN ISO 2768-1 National Ann

5、ex NA (informative) Bibliography DIN ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indication EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15272-2 March 2007 ICS 47.020.50; 47.060 English Version Inland navigation vessels - E

6、quipment for rope leading - Part 2: Fairlead Bateaux de navigation intrieure - Equipement de guidage de cble - Partie 2: Chaumard rouleaux Fahrzeuge der Binnenschifffahrt - Ausrstung zur Seilfhrung - Teil 2: Umlenkrolle This European Standard was approved by CEN on 3 February 2007. CEN members are b

7、ound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the

8、 CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same s

9、tatus as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Roman

10、ia, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reserved

11、 worldwide for CEN national Members. Ref. No. EN 15272-2:2007: EEN 15272-2:2007 (E) 2 Contents Page Foreword4 1 Scope 5 2 Normative references 5 3 Terms and definitions .5 4 Safety requirements 6 4.1 Dimensions.6 4.2 Strength 7 4.3 Material .7 4.4 Corrosion protection .7 4.5 Shaft bearing7 4.6 Fixin

12、g holes7 5 Test methods7 5.1 General7 5.2 Testing 7 6 Designation 8 6.1 Designation of a fairlead .8 6.2 Designation of a bush .8 7 Marking .8 8 Manufacturers certificate .8 Annex A (informative) Component parts of a fairlead made of cast steel.9 A.1 Materials .9 A.2 Component parts 10 A.2.1 Roller

13、10 A.2.2 Shaft . 12 A.2.3 Bush for shaft 13 A.2.4 Bush for roller . 13 A.2.5 Washer . 14 Annex B (informative) Example 15 B.1 Fairlead on deck 15 Bibliography. 16 Figures Figure 1 Fairlead 6 Figure A.1 Roller, item 1, for nominal size 2-8 . 10 Figure A.2 Roller, item 1, only for nominal size 1 11 Fi

14、gure A.3 Shaft, item 2 12 Figure A.4 Bush for shaft, item 3. 13 Figure A.5 Bush for roller, item 4 13 EN 15272-2:2007 (E) 3 Figure A.6 Washer, item 5.14 Figure B.1 Fairlead on deck15 Tables Table 1 Main dimensions 7 Table A.1 Materials 9 Table A.2 Dimensions for roller (cast).11 Table A.3 Shaft dime

15、nsions12 Table A.4 Dimensions for bushes and washer .14 EN 15272-2:2007 (E) 4 Foreword This document (EN 15272-2:2007) has been prepared by Technical Committee CEN/TC 15 “Inland navigation vessels”, the secretariat of which is held by DIN. This European Standard shall be given the status of a nation

16、al standard, either by publication of an identical text or by endorsement, at the latest by September 2007, and conflicting national standards shall be withdrawn at the latest by September 2007. prEN 15272 Inland navigation vessels Equipment for rope leading consists of: Part 1: General requirements

17、 Part 2: Fairlead Part 3: Roller fairleads Part 4: Rope lead According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland

18、, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 15272-2:2007 (E) 5 1 Scope This European Standard specifies requirements for fa

19、irleads on inland navigation vessels. It applies to fairleads for guiding ropes perpendicularly to the fairlead shaft. 2 Normative references The following referenced documents are indispensable for the application of this European Standard. For dated references, only the edition cited applies. For

20、undated references, the latest edition of the referenced document (including any amendments) applies EN 13573:2001, Inland navigation vessels Anchoring, coupling, towing, hauling and mooring systems prEN 15272-1, Inland navigation vessels Equipment for rope leading Part 1: General requirements EN IS

21、O 1302, Geometrical Product Specifications (GPS) - Indication of surface texture in technical product documentation (ISO 1302:2002) ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indication 3 Terms and definitions For the purposes of

22、this European Standard, the terms and definitions given in EN 13573:2001 and the following apply. 3.1 fairlead pedestal unit fairlead fairlead washer pulley with concave guide for reversing ropes EN 15272-2:2007 (E) 6 4 Safety requirements 4.1 Dimensions Dimensions in millimetres For general toleran

23、ces ISO 2768- accuracy grade m shall apply. Surface data shall be according to EN ISO 1302. Fairleads shall have no sharp edges or burr. Edges shall be rounded and have a radius R of at least 2 mm. Details not given need not comply with the illustration given here; compliance is only required for th

24、e dimensions and specifications given in clauses 4 to 7. Key 1 Roller 2 Shaft 3 Bush for shaft 4 Bush for roller 5 Washer aMarking bRib cFixing holes Figure 1 Fairlead EN 15272-2:2007 (E) 7 Table 1 Main dimensions Nominal size d1d3d4 d14H7 h1 r1s mm mm mm mm mm mm mm 1 160 210 195 60 80 25 1,5 2 200

25、 265 245 70 102 32 2,5 3 250 330 300 85 126 42 2,5 5 320 420 390 106 160 55 2,5 8 400 530 490 125 208 73 2,5 4.2 Strength The fairlead, its component parts and the fairlead fastening to the vessel shall withstand the basic test load as specified in prEN 15272-1 without any permanent deformation. 4.3

26、 Material All materials are permitted that meet the strength requirements specified in 4.2 except grey cast iron. Plastics shall be UV-resistant. 4.4 Corrosion protection Components susceptible to corrosion shall be permanently protected. 4.5 Shaft bearing The materials of the bearing shells shall b

27、e compatible with each other. The shaft bearings shall either be maintenance-free or capable of being lubricated. 4.6 Fixing holes In the case of rollers of nominal size 3 to 8, fixing holes shall be provided at the top of two ribs located opposite each other for connecting shackles. 5 Test methods

28、5.1 General The strength of the components can be proven by calculation or by testing. 5.2 Testing For the test, a rope is laid in a U-shape around the fairlead with the rope ends horizontal, i.e. perpendicular to the shaft. The tensile load of 1,25 times the minimum breaking load according to prEN

29、15272-1 shall be applied to both ends of the basic rope for 60 s. The load is applied 50 times. None of the fairlead components shall have undergone any permanent deformation and all of them shall be fully functional. EN 15272-2:2007 (E) 8 6 Designation 6.1 Designation of a fairlead Example of desig

30、nation of a fairlead according to Part 2 of this standard, nominal size 8: Fairlead EN 15272 2 8 6.2 Designation of a bush Designation of a bush according to Part 2 of this standard of nominal size 8, shaft P3 as component of the fairlead: Bush EN 15272 2 8 P3 NOTE Roller Figure A.1 and A.2 item 1:

31、P1 Shaft Figure A.3 item 2: P2 Bush for shaft Figure A.4 item 3: P3 Bush for roller Figure A.5, item 4: P4 Washer Figure A.6 item 5: P5 7 Marking The fairlead shall be marked on the upper inside surface (see Figure 1) with the following information: EN 15272-2; nominal size according to Table 1; man

32、ufacturer or manufacturers mark. 8 Manufacturers certificate The manufacturer shall declare conformity of the fairlead to this standard. EN 15272-2:2007 (E) 9 Annex A (informative) Component parts of a fairlead made of cast steel A.1 Materials Table A.1 Materials Material for Material ItemdPart Symb

33、ol No. to Note 1Roller (cast steel) EN-GJL-200 EN-JL 1030 EN 1561 2 Shaft S235JRG2 1.0038 EN 10025 3 Bush for shaft CuSn7Zn4Pb7-C CC493KaEN 1982 4 Bush for roller Polyamid 6 Gu (PA 6 G) with more than 4 % high-molecular low-pressure polyethyleneb, grade at the discretion of the manufacturer Density:

34、 1,15 g/cm Yield point stress: 58 N/mm Moisture absorption on free-lying surfaces: 2,2% max., but only 3 mm to 6 mm deepc 5 Washer Steel, grade at the discretion of the manufacturer aCasting method GZ bOther materials shall be the subject of a separate agreement. cMoisture absorption at standard atm

35、osphere ISO 554 20/65 1 dItem, see Figure 1 EN 15272-2:2007 (E) 10 A.2 Component parts A.2.1 Roller Key Groove dimensions, see X a Marking b Rib c Attachment holes for connecting shackles Figure A.1 Roller, item 1, for nominal size 2-8 EN 15272-2:2007 (E) 11 Dimensions according to Figure A.1 Figure

36、 A.2 Roller, item 1, only for nominal size 1 Table A.2 Dimensions for roller (cast) d11 Nom- inal size d1mm d2mm d3mm d4mm d5mm D6H7 mm d7H12 mm d8H12 mm d9mmd10mmmm Quantitya e mm f mm 1 160 170 210 195 110 90 72 89 2 200 240 265 245 120 100 82 99 130 155 3 250 290 330 300 140 115 97 116 155 1906 5

37、 320 370 420 390 180 144 117 140 195 240 8 400 460 530 490 220 170 137 164 240 2908 4 290 29 aWith a hole each uniformly positioned between the ribs. Table A.2 (concluded) h1h2h3h4h5h6r1r2 s1s2t1H13t2t3 bNom-inal size mm mm mm mm mm mm mm mm mm mm mm mm mm mm1 80 40 40 55 25 10 2 102 53 10 60 75 5 3

38、2 11 10 16 6 4,5 3 126 68 15 75 92 10 42 12 15 20 7 5 160 85 20 100 118 51 15 20 30 8 5 15 8 208 110 30 129 150 15 73 19 25 40 9 6 20 4 bRibs uniformly distributed over the circumference . EN 15272-2:2007 (E) 12 A.2.2 Shaft Key aPlan view: nominal size 1 to 5 bPlan view: nominal size 8 c 8,5 drilled

39、 after assembly with item 3 Figure A.3 Shaft, item 2 Table A.3 Shaft dimensions d12d13d14d15l1l2l3r3t4t5w1w2r6 min. Nom-inal size mm mm mm mm mm mm mm mm mm mm mm mm 1 60 85 60 68 61 30 2 70 95 70 89 81 20,5 15 38 20 3 85 110 85 M 10 111 98 25,5 48 5 106 140 106 50 142 124 0,8 26,5 20 56 10 8 125 16

40、5 125 M 16 60 184 156 1 31,5 25 60 EN 15272-2:2007 (E) 13 A.2.3 Bush for shaft Figure A.4 Bush for shaft, item 3 A.2.4 Bush for roller Figure A.5 Bush for roller, item 4 EN 15272-2:2007 (E) 14 A.2.5 Washer Key aPlan view: nominal size 1 to 5 bPlan view: nominal size 8 Figure A.6 Washer, item 5 Table

41、 A.4 Dimensions for bushes and washer d13d16d17d18d19 bd20d21h7a h8 bl3m r3s3s4 as5w1w2Nom-inal size mm h6 mm H7 mm z11 amm mm Toler-ance mm mm mm mm mm mm mm mm mm Toler-ance mm mm mm1 85 70 60 90 70,7 15,00+100 39 40 61 9,65 005,0302 95 80 70 100 80,8 16,00+110 58 60 81 9,6 006,08 38203 110 95 85

42、115 96,0 130 1173 75 98 9,5 007,0485 140 115 106 144 116,2 2,00+170 98 100 1240,8 1 13,9 009,010 56108 165 135 125 170 136,4 3,00+200 18126 129 15651 1,5 16,8 011,012 60 aThese dimensions are nominal sizes for the bush, item 4; they are no longer applicable after the bush has been fitted into the ro

43、ller. bThe bush dimensions are applicable after the bush has been fitted into the roller EN 15272-2:2007 (E) 15 Annex B (informative) Example B.1 Fairlead on deck Key d22 to fit d14according to Table A.3 z see Table 1 Figure B.1 Fairlead on deck EN 15272-2:2007 (E) 16 Bibliography 1 EN 1561, Founding Grey cast irons 2 EN 1982, Copper and copper alloys Ingots and castings 3 EN 10025 (all Parts), Hot rolled products of structural steels 4 ISO 554, Standard atmospheres for conditioning and for testing Specifications 5 ISO 2408, Steel wire ropes for general purposes Minimum requirements