DIN EN 1410-2008 Chemicals used for treatment of water intended for human consumption - Cationic polyacrylamides English version of DIN EN 1410 2008-04《人类用水处理的化学试剂 阳离子聚丙烯酰胺》.pdf

《DIN EN 1410-2008 Chemicals used for treatment of water intended for human consumption - Cationic polyacrylamides English version of DIN EN 1410 2008-04《人类用水处理的化学试剂 阳离子聚丙烯酰胺》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 1410-2008 Chemicals used for treatment of water intended for human consumption - Cationic polyacrylamides English version of DIN EN 1410 2008-04《人类用水处理的化学试剂 阳离子聚丙烯酰胺》.pdf（21页珍藏版）》请在麦多课文档分享上搜索。

1、April 2008DEUTSCHE NORM English price group 12No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 71.100.80!$NBK“1433140ww

2、w.din.deDDIN EN 1410Chemicals used for treatment of water intended for humanconsumption Cationic polyacrylamidesEnglish version of DIN EN 1410:2008-04Produkte zur Aufbereitung von Wasser fr den menschlichen Gebrauch Kationische PolyacrylamideEnglische Fassung DIN EN 1410:2008-04SupersedesDIN EN 1410

3、:1998-10www.beuth.deDocument comprises 21 pagesDIN EN 1410:2008-04 2 National foreword This standard has been prepared by Technical Committee CEN/TC 164 “Water supply” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was the Normenausschuss Wasserwesen (Water Pra

4、ctice Standards Committee), Technical Committee NA 119-04-02 AA Wasseraufbereitung. Users of this standard should note that national regulations exist in Germany dealing with the characteristics and treatment of water for human consumption, in particular the Trinkwasserverordnung (TrinkwV2001) (Germ

5、an Drinking Water Ordinance). Since cationic polyacrylamides are not mentioned in the list of substances for treatment and disinfection of water in accordance with article 11 of the Trinkwasserverordnung 2001, it shall not be used for the treatment of drinking water. The DIN Standards corresponding

6、to the International Standards referred to in clause 2 of the EN are as follows, whereby EN ISO Standards are only listed below if these have not been published as DIN EN ISO Standards with the same number: EN ISO 3696 DIN ISO 3696 Amendments This standard differs from DIN EN 1410:1998-10 as follows

7、: a) Reference to the Drinking Water Directive (Directive 98/83/EC) has been updated. b) The limit value for acrylamide monomer has been reduced from 250 mg/kg to 200 mg/kg. c) General purity criteria have been given in more detail. d) Specifications regarding the treatment dose have been extended.

8、Previous editions DIN EN 1410: 1998-10 National Annex NA (informative) Bibliography DIN ISO 3696, Water for analytical laboratory use Specification and test methods Verordnung zur Novellierung der Trinkwasserverordnung (German Regulation amending the German Drinking Water Ordinance), as of 21 May 20

9、01, BGBl. (German Federal Law Gazette) I, No. 24, pp. 9599801)1)Recorded in the DITR database of DIN Software GmbH, obtainable from Beuth Verlag GmbH, 10772 Berlin, Germany. EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 1410January 2008ICS 71.100.80 Supersedes EN 1410:1998 English VersionChemica

10、ls used for treatment of water intended for humanconsumption - Cationic polyacrylamidesProduits chimiques utiliss pour le traitement de leaudestine la consommation humaine - PolyacrylamidescationiquesProdukte zur Aufbereitung von Wasser fr denmenschlichen Gebrauch - Kationische PolyacrylamideThis Eu

11、ropean Standard was approved by CEN on 10 November 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

12、concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its

13、own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuan

14、ia, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN Al

15、l rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1410:2007: EDIN EN 1410:2008-04 EN 1410:2008 (E) 2 Contents Page Foreword4 Introduction .5 1 Scope 6 2 Normative references 6 3 Description .6 3.1 Identification.6 3.1.1 Chemical names.6 3.1.

16、2 Synonym or common name6 3.1.3 Relative molecular mass.6 3.1.4 Empirical formula.6 3.1.5 Chemical formulae.7 3.1.6 CAS Registry Numbers 7 3.1.7 EINECS reference .8 3.1.8 Commercial form .8 3.2 Physical properties8 3.2.1 Appearance 8 3.2.2 Density 8 3.2.3 Solubility.8 3.2.4 Vapour pressure 8 3.2.5 B

17、oiling point at 100 kPa .8 3.2.6 Melting point.8 3.2.7 Specific heat.9 3.2.8 Viscosity, dynamic.9 3.2.9 Critical temperature.9 3.2.10 Critical pressure.9 3.2.11 Physical hardness .9 3.3 Chemical properties 9 4 Purity criteria9 4.1 General9 4.2 Composition of commercial product.9 4.3 Impurities and m

18、ain by-products.10 4.4 Chemical parameters 10 5 Test methods10 5.1 Sampling.10 5.2 Analyses .10 5.2.1 General10 5.2.2 Main product 10 5.2.3 Impurity: residual acrylamide monomer content .10 6 Labelling - transportation - storage .15 6.1 Means of delivery.15 6.2 Risk and safety labelling in accordanc

19、e with the EU Directives 15 6.3 Transportation regulations and labelling15 6.4 Marking .15 6.5 Storage15 6.5.1 Long term stability.15 6.5.2 Storage incompatibilities 15 Annex A (informative) General information on cationic polyacrylamides .16 A.1 Origin 16 DIN EN 1410:2008-04 : EN 1410:2008 (E) 3 A.

20、2.2 A.2.4 A.2.6 A.3 Bibliography 19 A.1.1 Raw materials 16 A.1.2 Manufacturing process. 16 A.2 Use 16 Form in which it is used 17 Means of application. 17 A.2.1 Function 16 A.2.3 Treatment dose 17 A.2.5 Secondary effects 17 Removal of excess product 17 A.4 Emergency procedures. 18 A.4.1 First aid. 1

21、8 Rules for safe handling and use 17 A.4.2 Spillage. 18 A.4.3 Fire 18 DIN EN 1410:2008-04 : EN 1410:2008 (E) 4 Foreword This document (EN 1410:2008) has been prepared by Technical Committee CEN/TC 164 “Water supply”, the secretariat of which is held by AFNOR. This European Standard shall be given th

22、e status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2008, and conflicting national standards shall be withdrawn at the latest by July 2008. This document supersedes EN 1410:1998. Significant technical differences between this edition a

23、nd EN 1410:1998 are as follows: (a) reduction in the limit value for acrylamide from 250 mg/kg to 200 mg/kg in 4.4; (b) updating of the reference to the drinking water directive from 80/778/EEC to 98/83/EC; (c) provision of more information on treatment dose in Annex A. According to the CEN/CENELEC

24、Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg

25、, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. DIN EN 1410:2008-04 EN 1410:2008 (E) 5 Introduction In respect of potential adverse effects on the quality of water intended for human consumption, caused by the product covere

26、d by this European Standard: a) this European Standard provides no information as to whether the product may be used without restriction in any of the Member States of the EU or EFTA; b) it should be noted that, while awaiting the adoption of verifiable European criteria, existing national regulatio

27、ns concerning the use and/or the characteristics of this product remain in force. NOTE Conformity with this European Standard does not confer or imply acceptance or approval of the product in any of the Member States of the EU or EFTA. The use of the product covered by this European Standard is subj

28、ect to regulation or control by national authorities. DIN EN 1410:2008-04 EN 1410:2008 (E) 6 1 Scope This European Standard is applicable to cationic polyacrylamides used for treatment water intended for human consumption. It describes the characteristics of cationic polyacrylamides and specifies th

29、e requirements and the corresponding test methods for cationic polyacrylamides. It gives information on their use in water treatment. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies

30、. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 3696, Water for analytical laboratory use Specification and test methods (ISO 3696:1987) ISO 3165, Sampling of chemical products for industrial use Safety in sampling ISO 6206, Chemical

31、 products for industrial use Sampling Vocabulary ISO 8213, Chemical products for industrial use Sampling techniques Solid chemical products in the form of particles varying from powders to coarse lumps 3 Description 3.1 Identification 3.1.1 Chemical names Copolymer of acrylamide and amine ester or a

32、mide. 3.1.2 Synonym or common name Cationic polyacrylamide. NOTE The more general terms: “cationic polymer“, “cationic polyelectrolyte“ and “cationic flocculant“ are used but can also cover other chemicals referred to in other European Standards. 3.1.3 Relative molecular mass Typically in the range

33、of 1 to 20 million. 3.1.4 Empirical formula ()( )yxAONHCONHC53 dcbaDIN EN 1410:2008-04 EN 1410:2008 (E) 7 where A is a negative ion; a, b, c and d are variable depending on the cationic monomer; x and y are variable depending on the product. 3.1.5 Chemical formulae Copolymer of acrylamide and amine

34、ester Copolymer of acrylamide and amine amide where n and m are variables depending on the product. 3.1.6 CAS Registry Numbers 1)The following is a list of CAS Registry Numbers for typical cationic polyacrylamide polymers. 69418-26-4 26006-22-4 35429-19-7 25568-39-2 60162-07-4 1)Chemical Abstracts S

35、ervice Registry Number. DIN EN 1410:2008-04 EN 1410:2008 (E) 8 51410-72-1 52285-95-7 68227-15-6 55216-72-3 26796-75-8 45021-77-0 3.1.7 EINECS reference 2)The conformity of polymers to EINECS is assessed on the basis of the monomers of which they are composed. Thus, EINECS reference numbers do not ex

36、ist for polymers. 3.1.8 Commercial form Cationic polyacrylamide as specified in this standard is available as a solid containing a small amount of residual moisture. 3.2 Physical properties 3.2.1 Appearance The product is a white or off-white solid in the form of granule, flake or powder. 3.2.2 Dens

37、ity The bulk density of the product is typically in the range 0,5 g/cm3to 0,8 g/cm3. 3.2.3 Solubility The product is soluble in cold water. Its solubility is limited only by viscosity, with a gel being formed at concentrations of approximately 20 g/l and above. 3.2.4 Vapour pressure Not applicable.

38、3.2.5 Boiling point at 100 kPa 3)Not applicable. 3.2.6 Melting point The product decomposes at approximately 200 C. 2)European Inventory of Existing Commercial Chemical Substances. 3)100 kPa = 1 bar. DIN EN 1410:2008-04 EN 1410:2008 (E) 9 3.2.7 Specific heat Not applicable. 3.2.8 Viscosity, dynamic

39、Not applicable. 3.2.9 Critical temperature Not applicable. 3.2.10 Critical pressure Not applicable. 3.2.11 Physical hardness Not applicable. 3.3 Chemical properties Cationic polyacrylamide is a non hazardous material and not intrinsically reactive. However, in common with many other organic compound

40、s, a strong exothermic reaction will occur if it is brought into contact in the dry state with a strong acid or oxidizing agent. NOTE In dilute solution, there can be a reaction with, or destruction by, some of the disinfection and oxidizing agents used in water treatment. 4 Purity criteria 4.1 Gene

41、ral This European Standard specifies the minimum purity requirements for cationic polyacrylamides used for the treatment of water intended for human consumption. Limits are given for impurities commonly present in the product. Depending on the raw material and the manufacturing process other impurit

42、ies may be present and, if so, this shall be notified to the user and when necessary to relevant authorities. NOTE Users of this product should check the national regulations in order to clarify whether it is of appropriate purity for treatment of water intended for human consumption, taking into ac

43、count raw water quality, required dosage and contents of other impurities and additives used in the product not stated in the product standard. Limits have been given for impurities and chemical parameters where these are likely to be present in significant quantities from the current production pro

44、cess and raw materials. If the production process or raw materials lead to significant quantities of impurities, by-products or additives being present, this shall be notified to the user. 4.2 Composition of commercial product The cationic polyacrylamide shall be free of any visible extraneous matte

45、r. NOTE Various parameters can be checked as part of assessment of product quality (see 5.2.2). DIN EN 1410:2008-04 EN 1410:2008 (E) 10 4.3 Impurities and main by-products Based on the raw materials and manufacturing process (see A.1), there are no significant concentrations of additional reactants

46、or by-products which are relevant to the application of these products in drinking water treatment. 4.4 Chemical parameters The product shall contain no more than 200 mg of acrylamide monomer per kilogram of product. NOTE Other chemical parameters and indicator parameters as listed in EU Directive 9

47、8/83/EC (see 1) are not relevant to polyacrylamides because the raw materials used in the manufacturing process are free of them and they are not by-products of the manufacturing process. 5 Test methods 5.1 Sampling Sampling shall be in accordance with ISO 8213 and the recommendations given in ISO 3

48、165 and ISO 6206 shall be followed. A representative sample of the solid product, of sufficient mass, shall be obtained immediately after manufacture or from a newly opened package(s). The sample shall be clearly labelled with product name/code, batch number, type of container(s) sampled and date sa

49、mpled. Reference samples shall be retained for the storage life of the product as claimed by the manufacturer/supplier. 5.2 Analyses 5.2.1 General Unless otherwise specified, all reagents shall be of recognized analytical grade. The water used shall conform to grade 2 specified in EN ISO 3696. 5.2.2 Main product If additional requirements are agreed between the customer and the manufacturer/supplier, the latter shall provide the necessary test methods, if requested, so that the customer can carry out his own quality checks. A c