DIN EN 13617-4-2012 Petrol filling stations - Part 4 Safety requirements for construction and performance of swivels for use on metering pumps and dispensers German version EN 1361.pdf

《DIN EN 13617-4-2012 Petrol filling stations - Part 4 Safety requirements for construction and performance of swivels for use on metering pumps and dispensers German version EN 1361.pdf》由会员分享，可在线阅读，更多相关《DIN EN 13617-4-2012 Petrol filling stations - Part 4 Safety requirements for construction and performance of swivels for use on metering pumps and dispensers German version EN 1361.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、May 2012 Translation by DIN-Sprachendienst.English price group 10No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 75

2、.200!$|=“1892629www.din.deDDIN EN 13617-4Petrol filling stations Part 4: Safety requirements for construction and performance of swivelsfor use on metering pumps and dispensersEnglish translation of DIN EN 13617-4:2012-05Tankstellen Teil 4: Sicherheitstechnische Anforderungen an Bau- und Arbeitsweis

3、e von Drehgelenkenfr Zapfsulen und druckversorgte ZapfsulenEnglische bersetzung von DIN EN 13617-4:2012-05Stations-service Partie 4: Exigences de scurit relatives la construction et aux performances desraccords tournants utiliss sur les distributeurs de carburantsTraduction anglaise de DIN EN 13617-

4、4:2012-05SupersedesDIN EN 13617-4:2005-01www.beuth.deDocument comprises 16 pagesIn case of doubt, the German-language original shall be considered authoritative.04.12 DIN EN 13617-4:2012-05 2 A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Commit

5、tee CEN/TC 393 “Equipment for storage tanks and for service stations” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Tankanlagen (Tank Installations Standards Committee), Working Committee NA 104-02-06 AA Abgabeeinrichtungen an Tankstelle

6、n. Amendments This standard differs from DIN EN 13617-4:2005-01 as follows: a) a new note has been added at the end of the scope; b) an informative Annex B regarding environmental aspects has been included; c) normative references have been updated. Previous editions DIN EN 13617-4: 2005-01 EUROPEAN

7、 STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13617-4 March 2012 ICS 75.200 Supersedes EN 13617-4:2004English Version Petrol filling stations - Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and dispensers Stations-service - Partie 4: Exigences relat

8、ives laconstruction et aux performances descuritdes raccords tournants utiliss sur les distributeurs de carburants Tankstellen - Teil 4: Sicherheitstechnische Anforderungen an Bau- und Arbeitsweise von Drehgelenken fr Zapfsulen und druckversorgte Zapfsulen This European Standard was approved by CEN

9、on 28 January 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards

10、may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notifie

11、d to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

12、Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012

13、 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13617-4:2012: EEN 13617-4:2012 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .54 Explosion protection measures .55 Construction .55.1 General

14、 55.2 Connection threads .65.3 Safe breaks .66 Physical properties 67 Functional requirements .78 Frequency of testing .79 Information for use 89.1 General 89.2 Marking and instruction 8Annex A (normative) Testing .9A.1 General 9A.2 Fuel compatibility pre-conditioning .9A.3 Endurance 9A.4 Electrical

15、 resistance test 10A.5 Burst test . 10A.6 Drop test 10A.7 Leak test 10Annex B (informative) Environmental aspects 11Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 94/9/EC . 13DIN EN 13617-4:2012-05 EN 13617-4:2012 (E) 3 Foreword This

16、 document (EN 13617-4:2012) has been prepared by Technical Committee CEN/TC 393 “Equipment for tanks and filling stations”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement,

17、at the latest by September 2012, and conflicting national standards shall be withdrawn at the latest by September 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifyi

18、ng any or all such patent rights. This document supersedes EN 13617-4:2004. According to edition EN 13617-4:2004 the following fundamental changes are given: a new note at the end of the scope: Fuels other than of Explosion Group IIA are excluded from this European Standard added; informative Annex

19、B concerning environmental aspects added. This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directives. For relationship with EU Directives, see informative Annex ZA, whi

20、ch is an integral part of this standard. The present standard is composed of the following parts: Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units; Part 2: Safety requirements for construction and performance of safe breaks for use o

21、n metering pumps and dispensers; Part 3: Safety requirements for construction and performance of shear valves; Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and dispensers. According to the CEN/CENELEC Internal Regulations, the national standards o

22、rganizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,

23、 Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 13617-4:2012-05 EN 13617-4:2012 (E) 4 1 Scope This European Standard specifies safety requirements for the construction and performance of swivels to be fitted to delivery hose assemblies on met

24、ering pumps and dispensers installed at filling stations and used to dispense liquid fuels into the tanks of motor vehicles, boats and light aircraft and into portable containers at flow rates up to 200 l min-1. It pays particular attention to electrical, mechanical and hydraulic characteristics of

25、swivels. The requirements apply to swivels at ambient temperatures from 20 C to +40 C with the possibility for an extended temperature range. This European Standard applies mainly to hazards related to the ignition of liquid fuels being dispensed or their vapour. This European Standard also addresse

26、s electrical and mechanical hazards of swivels. This European Standard is not applicable to swivels for the dispensing of any compressed gas. NOTE 1 This European Standard does not apply to equipment for use with liquefied petroleum gas (LPG) or liquefied natural gas (LNG) or compressed natural gas

27、(CNG). NOTE 2 Fuels other than of Explosion Group IIA are excluded from this European Standard. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited app

28、lies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 228, Automotive fuels Unleaded petrol Requirements and test methods EN 11271, Explosive atmospheres Explosion prevention and protection Part 1: Basic concepts and methodology EN 1360, R

29、ubber and plastic hoses and hose assemblies for measured fuel dispensing systems Specification EN 13012:2001, Petrol filling stations Construction and performance of automatic nozzles for use on fuel dispensers EN 13463-1:2009 Non-electrical equipment for use in potentially explosive atmospheres Par

30、t 1: Basic method and requirements EN 13483, Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems Specification prEN 136171:2010 Petrol filling stations Part 1: Safety requirements for construction and performance of metering pumps, dispense

31、rs and remote pumping units EN 13617-2:2012, Petrol filling stations Part 2: Safety requirements for construction and performance of safe breaks for use on metering pumps and dispensers EN 60079-0, Explosive atmospheres Part 0: Equipment General requirements EN ISO 2281, Pipe threads where pressure-

32、tight joints are not made on the threads Part 1: Dimensions, tolerances and designation (ISO 228-1) EN ISO 1825, Rubber hoses and hose assemblies for aircraft ground fuelling and defuelling Specification (ISO 1825) DIN EN 13617-4:2012-05 EN 13617-4:2012 (E) 5 EN ISO 8031:2009, Rubber and plastics ho

33、ses and hose assemblies Determination of electrical resistance and conductivity (ISO 8031:2009) ISO 261, ISO general-purpose metric screw threads General plan ISO 9652, ISO general purpose metric screw threads Tolerances Part 2: Limits of sizes for general purpose external and internal screw threads

34、 Medium quality ISO 119253, Reaction to fire tests Ignitability of building products subjected to direct impingement of flame Part 3: Multi-source test 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 13012:2001, prEN 136171:2010 and EN 136172:2012 and

35、 the following apply: 3.1 swivel device fitted between nozzle and metering pump or dispenser to allow rotational movement 3.2 single plane swivel swivel with one plane of rotation 3.3 dual plane swivel swivel with two planes of rotation 4 Explosion protection measures 4.1 Explosion protection measur

36、es shall be taken in accordance with EN 1127-1 and Annex B of EN 13617-1:2012. 4.2 The swivel shall be explosion protected and shall be Category 2 in accordance with EN 134631. The vapour path of a vapour recovery swivel shall be Category 1 in accordance with EN 134631. The swivel shall fulfil the r

37、equirements for temperature Class T3 and Group IIA to EN 60079-0 or EN 134631. 5 Construction 5.1 General All electrical and non-electrical equipment and components, intended for use in potentially explosive atmospheres, shall be designed and constructed according to good engineering practice and in

38、 conformity with the required categories for Group II equipment to ensure avoidance of any ignition source. To classify the category of the equipment it shall be subjected to an ignition hazard assessment in accordance with 5.2 of EN 13463-1:2009. Materials used in the construction shall be chemical

39、ly and dimensionally stable under known service conditions. Materials likely to come into contact with fuels in both liquid and vapour phases shall be resistant to attack by these fuels. Conformity shall be demonstrated by manufacturers declaration and by the tests detailed in Annex A. Light alloys

40、when used shall conform to the requirements of 6.4.4.2 of EN 134631:2009. If other specifications for explosion protected equipment impose more stringent requirements then the more stringent requirement shall apply. DIN EN 13617-4:2012-05 EN 13617-4:2012 (E) 6 All components shall be of corrosion re

41、sistant material or shall be provided with a corrosion resistant protective coating. Outside surfaces likely to be handled shall be free of sharp edges. If protective covers are fitted they shall be constructed so that they allow ventilation and evaporation of fuel even if some shrinkage occurs. The

42、y shall not affect the performance of the swivels. The sealing surfaces of the connection threads shall be designed such that they are suitable for use with an enclosed O-ring or flat gasket. 5.2 Connection threads Connection threads shall be one of the following styles: Style 1 Swivels without a va

43、pour recovery path shall use parallel threads in accordance with EN ISO 2281. The connection thread dimensions shall be in accordance with Table 1 Table 1 Thread specifications Nominal connection size Inch Female threadsMaximum thread depthamm Male threads Minimum thread lengthbmm ” 12,5 11,01” 15,5

44、 14,01 ” 15,5 17,5 1 ” 15,5 18,0 aThe thread depth, measured from the outer fore-part to the metallic inner sealing face. bThe stated minimum length only applies if the female thread of the connection fitting includes an inner flat gasket. When no inner flat gasket is used the minimum thread length

45、depends on the tightness requirements of the threaded connection. Style 2: Swivels with a vapour recovery path shall use M 34 x 1,5 male outlet threads according to ISO 261 and ISO 965-2. The total thread length shall be maximum 15,0 mm. The inlet end shall be machined to a diameter of (35,0 0,05) m

46、m for a length (6,0 0,1) mm. 5.3 Safe breaks If a swivel has an integral safe break it shall fulfil the requirements of EN 136172. 6 Physical properties The physical properties of the swivel shall conform to the requirements given in Table 2 when tested by the methods indicated. DIN EN 13617-4:2012-

47、05 EN 13617-4:2012 (E) 7 Table 2 Physical properties of swivel Property Requirement Test method Electrical resistance between inlet and outlet when assembled. 105 A.4 Electrostatic properties 6.7 EN 13463-1:2009 EN 13463-1 Fuel compatibility 5.1 A.2 followed by A.6, A.7 and A.5Endurance Clause 6 and

48、 electrical resistance test 105 after endurance test A.3 Ignitability of composites on the swivel. Ignition source C; Effect time 20 s; Surface flame impingement The material tested shall not flame ISO 119253 Characteristics of swivel components and/or covers to prevent dangerous, mechanically generated, sparks (resistance to sparking). 6.4.4.2 EN 134631:2009 EN 134631 7 Functional requirements The swivel