DIN EN 12201-2-2013 Plastics piping systems for water supply and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2 Pipes German version EN 12201-2 2011+A1 2013《.pdf

《DIN EN 12201-2-2013 Plastics piping systems for water supply and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2 Pipes German version EN 12201-2 2011+A1 2013《.pdf》由会员分享，可在线阅读，更多相关《DIN EN 12201-2-2013 Plastics piping systems for water supply and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2 Pipes German version EN 12201-2 2011+A1 2013《.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、December 2013 Translation by DIN-Sprachendienst.English price group 14No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).I

2、CS 23.040.20!%*zq“2078778www.din.deDDIN EN 12201-2Plastics piping systems for water supply, and for drainage andsewerage under pressure Polyethylene (PE) Part 2: Pipes;English version EN 12201-2:2011+A1:2013,English translation of DIN EN 12201-2:2013-12Kunststoff-Rohrleitungssysteme fr die Wasserver

3、sorgung und fr Entwsserungs- undAbwasserdruckleitungen Polyethylen (PE) Teil 2: Rohre;Englische Fassung EN 12201-2:2011+A1:2013,Englische bersetzung von DIN EN 12201-2:2013-12Systmes de canalisations en plastique pour lalimentation en eau et pour lesbranchements et les collecteurs dassainissement av

4、ec pression Polythylne (PE) Partie 2: Tubes;Version anglaise EN 12201-2:2011+A1:2013,Traduction anglaise de DIN EN 12201-2:2013-12SupersedesDIN EN 12201-2:2011-11www.beuth.deDocument comprises 30 pagesIn case of doubt, the German-language original shall be considered authoritative.12.13DIN EN 12201-

5、2:2013-12 2 A comma is used as the decimal marker. National foreword This document (EN 12201-2:2011+A1:2013) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems” (Secretariat: NEN, Netherlands). The responsible German body involved in its preparation was

6、the Normenausschuss Wasserwesen (Water Practice Standards Committee), Working Committee NA 119-04-06-08 GUA Erdverlegte Druckrohrleitungen aus thermoplastischen Werkstoffen of Joint Working Committee NA 119-04-06 GA Kunststoffrohre in der Trinkwasserversorgung. The Committee would like to point out

7、the provisions regarding the colour of pipes intended to convey water for human consumption (see Subclause 5.2) applicable in Germany as laid down in the body of technical rules and standards for gas and water issued by the DVGW Deutscher Verein des Gas- und Wasserfaches e.V. (German Technical and S

8、cientific Association for Gas and Water). According to DVGW GW 335-A2 the following colours apply: Pipes Stripes Outer peelable layer Outer coextruded layer PE 80 black RAL 9004 Light blue RAL 5012 PE 100 royal blue RAL 5005 PE 100 black RAL 9004 Royal blue RAL 5005 Royal blue RAL 5005 Royal blue RA

9、L 5005 The colours of the outer surfaces should be roughly equivalent to the specified RAL colours (see table). In Germany, blue or black with blue stripes normally indicate pipes intended for drinking water. Amendments This standard differs from DIN EN 12201-2:2011-11 as follows: a) wall thicknesse

10、s of pipes of nominal sizes DN/OD 1 000, 1 400, 1 600 and 2 000 and standard dimension ratio SDR of 13,6 and 17 and of pipes of nominal sizes DN/OD 2 250 and 2 500 and standard dimension ratio SDR 26 and 33 have been corrected; b) the temperature for the determination of the longitudinal reversion o

11、f PE 40 pipes has been reduced. Previous editions DIN 19533: 1966-05,1976-03 DIN EN 12201-2: 2003-06, 2011-11 DIN EN 13244-2: 2003-04 DIN EN 13244-2 Corrigendum 1: 2003-08 DIN EN 12201-2:2013-12 3 National Annex NA (informative) Bibliography DVGW GW 335-A2, Kunststoff-Rohrleitungssysteme in der Gas-

12、 und Wasserverteilung Anforderungen und Prfungen Teil A2: Rohre aus PE 80 und PE 100 (Plastic pipeline systems in gas and water distribution Requirements and tests Part A 2: PE 80 and PE 100 pipes)1)1 )Obtainable from: Wirtschafts- und Verlagsgesellschaft Gas und Wasser mbH, Postfach 140151, 53056 B

13、onn.DIN EN 12201-2:2013-12 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12201-2:2011+A1 September 2013 ICS 23.040.20 Supersedes EN 12201-2:2011 English Version Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethy

14、lene (PE) - Part 2: Pipes Systmes de canalisations en plastique pour lalimentation en eau et pour les branchements et les collecteurs dassainissement avec pression - Polythylne (PE) - Partie 2: Tubes Kunststoff-Rohrleitungssysteme fr die Wasserversorgung und fr Entwsserungs- und Abwasserdruckleitung

15、en - Polyethylen (PE) - Teil 2: Rohre This European Standard was approved by CEN on 8 July 2011 and includes Amendment 1 approved by CEN on 12 August 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the s

16、tatus of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French,

17、 German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cr

18、oatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

19、 United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No

20、. EN 12201-2:2011+A1:2013: E EN 12201-2:2011+A1:2013 (E) 2 Contents Page Foreword 3 Introduction . 5 1 Scope 6 2 Normative references . 7 3 Terms and definitions, symbols and abbreviations 7 4 Material . 8 4.1 Compound 8 4.2 Compound for identification stripes 8 5 General characteristics 8 5.1 Appea

21、rance . 8 5.2 Colour 8 5.3 Effect on water quality . 9 6 Geometrical characteristics . 9 6.1 Measurements 9 6.2 Mean outside diameter, out-of-roundness (ovality) and tolerances . 9 6.3 Wall thicknesses and their tolerances . 11 6.4 Coiled pipe 14 6.5 Pipe lengths 14 7 Mechanical characteristics 14 7

22、.1 Conditioning . 14 7.2 Requirements . 14 7.3 Retest in case of failure at 80 C 16 7.4 Pipe stiffness for vacuum sewer systems 16 8 Physical characteristics . 16 8.1 Conditioning . 16 8.2 Requirements . 16 9 Chemical characteristics of pipes in contact with chemicals 17 10 Performance requirements

23、17 11 Marking. 18 11.1 General 18 11.2 Minimum required marking of pipes 18 Annex A (informative) Relationship between PN, MRS, S and SDR 19 Annex B (normative) Pipes with co-extruded layers . 20 Annex C (normative) Pipes with peelable layer . 22 Annex D (normative) Pipe stiffness for vacuum sewer s

24、ystems . 24 Bibliography 26 DIN EN 12201-2:2013-12 EN 12201-2:2011+A1:2013 (E) 3 Foreword This document (EN 12201-2:2011+A1:2013) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. This European Standard shall b

25、e given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2014, and conflicting national standards shall be withdrawn at the latest by March 2014. Attention is drawn to the possibility that some of the elements of this document ma

26、y be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document includes Amendment 1 approved by CEN on 12 August 2013. This document supersedes !EN 12201-2:2011“. The start and finish of text introduced or altered by a

27、mendment is indicated in the text by tags !“. !This document includes Amendment A1 to EN 12201-2:2011 that comprises technical changes to: Subclause 6.3, Wall thicknesses and their tolerances; Subclause 8.2, Requirements, Table 5, Physical Requirements, physical longitudinal reversion test.“ System

28、Standards are based on the results of the work being undertaken in ISO/TC 138, “Plastics pipes, fittings and valves for the transport of fluids“, which is a Technical Committee of the International Organization for Standardization (ISO). They are supported by separate standards on test methods to wh

29、ich references are made throughout the System Standard. The System Standards are consistent with general standards on functional requirements and on recommended practice for installation. EN 12201 consists of the following parts: EN 12201-1:, Plastics piping systems for water supply, and for drainag

30、e and sewerage under pressure Polyethylene (PE) Part 1: General; EN 12201-2:, Plastics piping systems for water supply, and for drainage and sewerage under pressure Polyethylene (PE) Part 2: Pipes (this standard); EN 12201-3:, Plastics piping systems for water supply, and for drainage and sewerage u

31、nder pressure Polyethylene (PE) Part 3: Fittings; EN 12201-4 , Plastics piping systems for water supply, and for drainage and sewerage under pressure Polyethylene (PE) Part 4: Valves for water supply systems; EN 12201-5, Plastics piping systems for water supply, and for drainage and sewerage under p

32、ressure Polyethylene (PE) Part 5: Fitness for purpose of the system; CEN/TS 12201-7, Plastics piping systems for water supply Polyethylene (PE) Part 7: Guidance for the assessment of conformity. In this revision, the scope of this standard includes two additional types of pipe;- DIN EN 12201-2:2013-

33、12 EN 12201-2:2011+A1:2013 (E) 4 PE pipes with co-extruded layers on either or both the outside and/or inside of the pipe as specified in Annex B, where all layers have the same MRS rating; PE pipes with a peelable, contiguous thermoplastics additional layer on the outside of the pipe (coated pipe)

34、as specified in Annex C. In this revision, pipe diameters specified have been increased to 2 500 mm. Test methods have been updated as appropriate and in accordance with other parts of this standard. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the follo

35、wing countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, N

36、orway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 12201-2:2013-12 EN 12201-2:2011+A1:2013 (E) 5 Introduction The System Standard, of which this is Part 2, specifies the requirements for a piping system and its components when made

37、 from polyethylene (PE). The piping system is intended to be used for water supply intended for human consumption, including the conveyance of raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes. In respect of potential adverse effec

38、ts on the quality of water intended for human consumption, caused by the product covered by EN 12201 (all parts): a) this standard provides no information as to whether the product may be used without restriction in any of the Member States of the EU or EFTA; b) products intended for use in water su

39、pply systems must comply, when existing, with national regulations and testing arrangements that ensure fitness for contact with drinking water. NOTE On April 2006, EC Commission set up a revised mandate (M/136) asking CEN to propose harmonised product standards and support standards for test method

40、s which could be used for assessing the fitness for contact with drinking water. In parallel, EC Commission has launched processes for a regulation of construction products (CPR) to be substituted to CP directive (89/106/EEC) and for the revision of drinking water directive (98/83/EC). If relevant,

41、when the outputs of these processes will be known, European Product Standards will be amended by the addition of an Annex Z under Mandate M136, which will contain formal references to the applicable requirements. Until such amendments, the current national regulations remain applicable. Requirements

42、 and test methods for material and components, other than pipes, are specified in EN 12201-1:2011, EN 12201-3:2011 1 and prEN 12201-4:2011 2. Characteristics for fitness of purpose are covered in EN 12201-5:2011 and CEN/TS 12201-7 3 gives guidance for the assessment of conformity. This Part of EN 12

43、201 covers the characteristics of pipes. DIN EN 12201-2:2013-12 EN 12201-2:2011+A1:2013 (E) 6 1 Scope This part of EN 12201 specifies the characteristics of pipes made from polyethylene (PE 100, PE 80 and PE 40) for buried and above ground applications, intended for the conveyance of water for human

44、 consumption, raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes. NOTE 1 For PE components intended for the conveyance of water for human consumption and raw water prior to treatment attention is drawn to 5.3 of this European Standa

45、rd. Components manufactured for water for general purposes, drainage and sewerage may not be suitable for water supply for human consumption. It also specifies the test parameters for the test methods referred to in this standard. In conjunction with Part 1 and Parts 3 to 5 of EN 12201, it is applic

46、able to PE pipes, their joints and to joints with components of PE and other materials intended to be used under the following conditions: a) allowable operating pressure, PFA, up to 25 bar 1); b) an operating temperature of 20 C as a reference temperature; c) buried in the ground; d) sea outfalls;

47、e) laid in water; f) above ground, including pipes suspended below bridges. NOTE 2 For applications operating at constant temperatures greater than 20 C and up to 40 C, see Annex A of EN 12201-1:2011. NOTE 3 Pipes constructions including barrier layers are not covered by this document. EN 12201 cove

48、rs a range of allowable operating pressures and gives requirements concerning colours and additives. It covers three types of pipe: PE pipes (outside diameter dn) including any identification stripes; PE pipes with co-extruded layers on either or both the outside and/or inside of the pipe (total out

49、side diameter dn) as specified in Annex B, where all layers have the same MRS rating; PE pipes (outside diameter dn) with a peelable, contiguous thermoplastics additional layer on the outside of the pipe (coated pipe) as specified in Annex C. NOTE 4 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installat