DIN 8077-2008 Polypropylene (PP) pipes - PP-H PP-B PP-R PP-RCT - Dimensions《聚丙烯(PP)管 PP-H、PP-B、PP-R、PP-RCT 尺寸》.pdf

《DIN 8077-2008 Polypropylene (PP) pipes - PP-H PP-B PP-R PP-RCT - Dimensions《聚丙烯(PP)管 PP-H、PP-B、PP-R、PP-RCT 尺寸》.pdf》由会员分享，可在线阅读，更多相关《DIN 8077-2008 Polypropylene (PP) pipes - PP-H PP-B PP-R PP-RCT - Dimensions《聚丙烯(PP)管 PP-H、PP-B、PP-R、PP-RCT 尺寸》.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、September 2008DEUTSCHE NORM Translation by DIN-Sprachendienst.English price group 15No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards

2、(DIN-Normen).ICS 23.040.20!$R(“1476105www.din.deDDIN 8077Polypropylene (PP) pipes PP-H, PP-B, PP-R, PP-RCT DimensionsRohre aus Polypropylen (PP) PP-H, PP-B, PP-R, PP-RCT MaeSupersedesDIN 8077:2007-05www.beuth.deDocument comprises 34 pagesIn case of doubt, the German-language original should be consu

3、lted as the authoritative text.DIN 8077:2008-09 2 Contents Page Foreword4 1 Scope 5 2 Normative references 5 3 Terms and definitions .5 4 Safety factors .6 5 Dimensions and designation7 5.1 General7 5.2 Outside diameters, wall thicknesses, S/SDR series and masses.8 5.3 Tolerances on mean outside dia

4、meters and out-of-roundness. 11 5.4 Tolerances on wall thicknesses 13 6 Allowable operating pressures . 15 6.1 Allowable operating pressures for pipes conveying water 15 6.2 Allowable operating pressures for pipes conveying other fluids . 15 7 Form supplied . 31 8 Marking 32 Annex A (informative) Ex

5、planatory notes 33 Annex B (informative) Bibliography . 34 Figures Figure 1 Outside diameter and wall thickness .7 Tables Table 1 Safety factor SF as a function of the temperature 6 Table 2 Outside diameters, wall thicknesses, S/SDR series and masses.8 Table 3 Tolerances on mean outside diameters an

6、d out-of-roundness . 11 Table 4 Tolerances on wall thicknesses . 13 Table 5 Allowable operating pressures for PP-H pipes conveying water, safety factor (SF) = 1,6 1,25 (temperature-dependent) 16 Table 6 Allowable operating pressures for PP-H pipes conveying water, safety factor (SF) = 1,7 18 Table 7

7、 Allowable operating pressures for PP-B pipes conveying water, safety factor (SF) = 1,25 20 Table 8 Allowable operating pressures for PP-B pipes conveying water, safety factor (SF) = 1,5 22 Table 9 Allowable operating pressures for PP-R pipes conveying water, safety factor (SF) = 1,25 24 Table 10 Al

8、lowable operating pressures for PP-R pipes conveying water, safety factor (SF) = 1,5 26 DIN 8077:2008-09 3 Page Table 11 Allowable operating pressures for PP-RCT pipes conveying water, safety factor (SF) = 1,2528 Table 12 Allowable operating pressures for PP-RCT pipes conveying water, safety factor

9、(SF) = 1,530 Table 13 Tolerances on nominal lengths.31 DIN 8077:2008-09 4 Foreword This standard has been prepared by Technical Committee NA 054-05-01 AA Auendurchmesser und Betriebsdrcke of the Normenausschuss Kunststoffe (Plastics Standards Committee). The relationship with ISO 161-1 published by

10、the International Organization for Standardization (ISO) is shown in Appendix A. DIN, the German Institute for Standardization, would like to bring attention to the fact that complying with this standard can involve exploitation of Patent EP1448631 in regard to material PP-RCT. DIN takes no postitio

11、n on the legitimacy, validity or scope of this patent. The holder of this patent has declared to DIN he is prepared to negotiate with applicants from any part of the world licences under reasonable and non-discriminatory business conditions as laid down in his declaration. The declaration of the hol

12、der of patent EP 1448631 is registered with DIN. Information can be obtained from the patent holder at this address: Att: Managing Director Borealis Technology Oy | P.O. Box 330 | FI-06101 Porvoo | Finland Tel. +358 9 3949 00 e-mail: Attention is drawn to the possibility that some of the elements o

13、f this document may be the subject of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. Amendments This standard differs from DIN 8077:1999-07 as follows: a) The material designation has been amended (see Explanatory notes in Appendix A). b) Type PP-RCT

14、polypropylene has been included. c) The S/SDR series has been extended in the dimension and operating pressure tables. d) The operating pressure tables have been revised and corrected. e) The explanatory notes have been revised. This standard differs from DIN 8077:2007-05 as follows: a) A reference

15、to patent rights has been added to the Foreword. b) The description of PP-RCT polypropylene has been modified. c) A reference to existing European product standards has been added to the Scope. Previous editions DIN 8077: 1974-02, 1989-01, 1997-12, 1999-07, 2007-05 DIN 8077:2008-09 5 1 Scope This st

16、andard is applicable to pipes made from homopolymer polypropylene (PP-H), block copolymer polypropylene (PP-B), random copolymer polypropylene (PP-R) and random copolymer polypropylene with modified crystalline structure and elevated temperature resistance (PP-RCT) as specified in DIN 8078. Attentio

17、n is brought to the fact that existing European product standards apply for some specific applications, which are to be complied with where necessary. Some of these product standards are listed in the Bibliography for the information of users of this standard. Please note that because European Stand

18、ards are continually being developed, this list is not exhaustive. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docu

19、ment (including any amendments) applies. DIN 8078, Polypropylene (PP) pipes PP-H, PP-B, PP-R, PP-RCT General quality requirements and testing ISO 4065, Thermoplastics pipes Universal wall thickness table 3 Terms and definitions For the purposes of this document, the following terms and definitions a

20、pply: 3.1 pipe series number S nominal pipe series number taken from ISO 4065 NOTE To calculate the wall thickness e using equation (1), the “calculated” S-values in ISO 4065 are to be used. 1S2 +d= e(1) 3.2 standard dimension ratio SDR ratio of the outside diameter of a pipe to its wall thickness N

21、OTE It is calculated using equation (2). ed= +1S2SDR(2) The nominal pipe series number shall be used for S. DIN 8077:2008-09 6 4 Safety factors Safety factors shall be specified in the application standards. Minimum safety factors SF are given in Table 1 and take account of the material characterist

22、ics. Since the impact strength of PP-H decreases as the temperature increases, the safety factors have been classified as a function of the temperature. Table 1 Safety factor SF as a function of the temperature Temperature Material designation 10 to less than 40 C 40 to less than 60 C from 60 C upwa

23、rds PP-H 1,6 1,4 1,25 PP-B 1,25 PP-R 1,25 PP-RCT 1,25 Values for the allowable operating pressures are given in Tables 5, 7, 9 and 11, taking into account the safety factor specified in Table 1. Tables 6, 8, 10 and 12 include additional values based on a constant safety factor SF of 1,7 (for PP-H) a

24、nd 1,5 (for PP-B, PP-R, PP-RCT). DIN 8077:2008-09 7 5 Dimensions and designation 5.1 General The main dimensions characterizing the pipes are illustrated in Figure 1. Figure 1 Outside diameter and wall thickness Designation of a pipe made from PP-B, with an outside diameter d of 50 mm and a wall thi

25、ckness e of 2,9 mm: Pipe DIN 8077 50 2,9 PP-B DIN 8077:2008-09 8 5.2 Outside diameters, wall thicknesses, S/SDR series and masses Table 2 Outside diameters, wall thicknesses, S/SDR series and masses Pipe series S 20 16 12,5 8,3 8 5 4 3,2 2,5 2 Standard dimension ratio SDR 41 33 26 17,6 17 11 9 7,4 6

26、 5 d ea mm Mass bkg/m ea mm Mass bkg/m ea mm Mass bkg/m ea mm Mass bkg/m ea mm Mass bkg/m ea mm Mass bkg/m ea mm Mass bkg/m ea mm Mass bkg/m ea mm Mass bkg/m ea mm Mass bkg/m 10 1,8 0,046 2,0 0,050 12 1,8 0,057 2,0 0,062 2,4 0,071 16 1,8 0,080 2,2 0,095 2,7 0,110 3,3 0,128 20 1,9 0,107 2,3 0,127 2,8

27、 0,148 3,4 0,172 4,1 0,198 25 2,3 0,164 2,8 0,191 3,5 0,230 4,2 0,266 5,1 0,307 32 1,8 0,172 1,9 0,180 2,9 0,261 3,6 0,313 4,4 0,370 5,4 0,434 6,5 0,498 40 1,8 0,217 2,3 0,273 2,4 0,283 3,7 0,412 4,5 0,487 5,5 0,575 6,7 0,671 8,1 0,775 50 1,8 0,274 2,0 0,301 2,9 0,422 3,0 0,434 4,6 0,638 5,6 0,755 6

28、,9 0,896 8,3 1,04 10,1 1,21 63 1,8 0,349 2,0 0,382 2,5 0,474 3,6 0,659 3,8 0,690 5,8 1,01 7,1 1,20 8,6 1,41 10,5 1,65 12,7 1,91 75 1,9 0,438 2,3 0,528 2,9 0,647 4,3 0,935 4,5 0,973 6,8 1,41 8,4 1,69 10,3 2,01 12,5 2,34 15,1 2,70 90 2,2 0,616 2,8 0,758 3,5 0,936 5,1 1,33 5,4 1,40 8,2 2,03 10,1 2,44 1

29、2,3 2,87 15,0 3,36 18,1 3,88 aThe minimum wall thickness has been set as e = 1,8 mm. bThe masses have been calculated taking an average density of 0,910 g/cm3. For other densities, the masses shall be corrected proportionally. Half the specified tolerance has been added to the wall thickness. The va

30、lues have been rounded to 3 decimal places. DIN 8077:2008-09 9 Table 2 (continued) Pipe series S 20 16 12,5 8,3 8 5 4 3,2 2,5 2 Standard dimension ratio SDR 41 33 26 17,6 17 11 9 7,4 6 5 d ea mm Mass bkg/m ea mm Mass bkg/m ea mm Mass bkg/m ea mm Mass bkg/m ea mm Mass bkg/m ea mm Mass bkg/m ea mm Mas

31、s bkg/m ea mm Mass bkg/m ea mm Mass bkg/m ea mm Mass bkg/m 110 2,7 0,903 3,4 1,12 4,2 1,37 6,3 1,99 6,6 2,09 10,0 3,01 12,3 3,62 15,1 4,30 18,3 5,01 22,1 5,78 125 3,1 1,18 3,9 1,45 4,8 1,76 7,1 2,55 7,4 2,65 11,4 3,91 14,0 4,66 17,1 5,53 20,8 6,47 25,1 7,46 140 3,5 1,48 4,3 1,80 5,4 2,23 8,0 3,20 8,

32、3 3,32 12,7 4,87 15,7 5,86 19,2 6,95 23,3 8,12 28,1 9,35 160 4,0 1,91 4,9 2,32 6,2 2,92 9,1 4,17 9,5 4,33 14,6 6,38 17,9 7,62 21,9 9,04 26,6 10,6 32,1 12,2 180 4,4 2,38 5,5 2,94 6,9 3,63 10,2 5,25 10,7 5,47 16,4 8,07 20,1 9,64 24,6 11,4 29,0 13,4 36,1 15,4 200 4,9 2,92 6,2 3,68 7,7 4,50 11,4 6,50 11

33、,9 6,75 18,2 9,95 22,4 11,9 27,4 14,1 33,2 16,5 225 5,5 3,70 6,9 4,57 8,6 5,65 12,8 8,19 13,4 8,56 20,5 12,6 25,2 15,1 30,8 17,9 37,4 20,9 250 6,2 4,63 7,7 5,67 9,6 6,99 14,2 10,1 14,8 10,5 22,7 15,5 27,9 18,5 34,2 22,1 280 6,9 5,73 8,6 7,09 10,7 8,72 15,9 12,6 16,6 13,2 25,4 19,4 31,3 23,3 38,3 27,

34、6 315 7,7 7,20 9,7 8,97 12,1 11,1 17,9 16,0 18,7 16,7 28,6 24,6 35,2 29,5 355 8,7 9,14 10,9 11,3 13,6 14,0 20,1 20,3 21,1 21,2 32,2 31,2 39,7 37,4 aThe minimum wall thickness has been set as e = 1,8 mm. bThe masses have been calculated taking an average density of 0,910 g/cm3. For other densities, t

35、he masses shall be corrected proportionally. Half the specified tolerance has been added to the wall thickness. The values have been rounded to 3 decimal places. DIN 8077:2008-09 10 Table 2 (concluded) Pipe series S 20 16 12,5 8,3 8 5 4 3,2 2,5 2 Standard dimension ratio SDR 41 33 26 17,6 17 11 9 7,

36、4 6 5 d ea mm Mass bkg/m ea mm Mass bkg/m ea mm Mass bkg/m ea mm Mass bkg/m ea mm Mass bkg/m ea mm Mass bkg/m ea mm Mass bkg/m ea mm Mass bkg/m ea mm Mass bkg/m ea mm Mass bkg/m 400 9,8 11,6 12,3 14,4 15,3 17,8 22,7 25,7 23,7 26,8 36,3 39,6 450 11,0 14,7 13,8 18,2 17,2 22,5 25,5 32,5 26,7 33,9 40,9

37、50,1 500 12,3 18,2 15,3 22,6 19,1 27,7 28,4 40,2 29,7 41,9 560 13,7 22,6 17,2 28,2 21,4 34,7 31,7 50,3 33,2 52,5 630 15,4 28,6 19,3 35,6 24,1 44,0 35,7 63,7 37,4 66,5 710 17,4 36,4 21,8 45,2 27,2 55,9 40,2 80,8 42,1 84,4 800 19,6 46,1 24,5 57,2 30,6 70,8 45,3 103 47,4 107 900 22,0 58,3 27,6 72,5 34,

38、4 89,5 51,0 130 53,3 135 1000 24,5 72,0 30,6 89,2 38,2 110 1200 29,4 104 36,7 128 45,9 159 1400 34,3 141 42,9 175 53,5 216 1600 39,2 184 49,0 228 61,2 283 aThe minimum wall thickness has been set as e = 1,8 mm. bThe masses have been calculated taking an average density of 0,910 g/cm3. For other dens

39、ities, the masses shall be corrected proportionally. Half the specified tolerance has been added to the wall thickness. The values have been rounded to 3 decimal places. DIN 8077:2008-09 11 5.3 Tolerances on mean outside diameters and out-of-roundness Table 3 Tolerances on mean outside diameters and

40、 out-of-roundness Dimensions in millimetres Tolerance on out-of-roundnesscTolerance on out-of-roundnesscd Tolerances on mean outside diameter a bStraight pipes Coiled pipes d Tolerances on mean outside diametera bStraight pipes Coiled pipes 10 +0,3 (+0,3) 0 1,1 1,0 75 +0,7 (+0,5) 0 1,6 12 +0,3 (+0,3

41、) 0 1,1 1,0 90 +0,9 (+0,6) 0 1,8 16 +0,3 (+0,3) 0 1,2 1,0 110 +0,9 (+0,6) 0 2,2 20 +0,3 (+0,3) 0 1,2 1,2 125 +1,2 (+0,8) 0 2,5 25 +0,3 (+0,3) 0 1,2 1,5 140 +1,3 (+0,9) 0 2,8 32 +0,3 (+0,3) 0 1,3 2,0 160 +1,5 (+1,0) 0 3,2 40 +0,4 (+0,3) 0 1,4 2,4 180 +1,7 (+1,1) 0 3,6 50 +0,5 (+0,3) 0 1,4 3,0 200 +1,

42、8 (+1,2) 0 4,0 63 +0,6 (+0,4) 0 1,6 3,8 225 +2,1 (+1,4) 0 4,5 aThe values given have been calculated as follows: tolerance on mean outside diameter: for d 400 mm: +0,009 d, rounded up to the nearest 0,1 mm, at least 0,3 mm; for d = 450 mm to 710 mm: +0,004 d + 2 mm, rounded up to the nearest 0,1 mm;

43、 for d = 800 mm to 1 000 mm: +5,0 mm; for d = 1 200 mm to 1 600 mm: +6,0 mm. bThe dimensions in brackets are restricted tolerances on the mean outside diameter for electrofusion welding: +0,006 d rounded up to the nearest 0,1 mm, at least 0,3 mm. cThe values given have been calculated as follows: to

44、lerance on out-of-roundness: Straight pipes: d 75 mm: 0,008 d + 1 mm, rounded up to the nearest 0,1 mm; d = 90 mm to 250 mm: 0,02 d, rounded up to the nearest 0,1 mm; d 250 mm: 0,035 d, rounded up to the nearest 0,1 mm. Coiled pipes: d 63 mm: 0,06 d, rounded up to the nearest 0,1 mm; at least 1,0 mm

45、; d 75 mm: subject to agreement when determining the delivery conditions. DIN 8077:2008-09 12 Table 3 (concluded) Tolerance on out-of-roundnesscTolerance on out-of-roundnesscd Tolerances on mean outside diametera bStraight pipes Coiled pipes d Tolerances on mean outside diameter a bStraight pipes Co

46、iled pipes 250 +2,3 (+1,5) 0 5,0 630 +4,6 0 22,1 280 +2,5 (+1,7) 0 9,8 710 +4,9 0 24,9 315 +2,5 (+1,9) 0 11,1 800 +5,0 0 28,0 355 +3,2 0 12,5 1 000 +5,0 0 35,0 400 +3,6 0 14,0 1 200 +6,0 0 42,0 450 +3,8 0 15,8 1 400 +6,0 0 49,0 500 +4,0 0 17,5 1 600 +6,0 0 56,0 560 +4,3 0 19,6 aThe values given have

47、 been calculated as follows: tolerance on mean outside diameter: for d 400 mm: +0,009 d, rounded up to the nearest 0,1 mm, at least 0,3 mm; for d = 450 mm to 710 mm: +0,004 d + 2 mm, rounded up to the nearest 0,1 mm; for d = 800 mm to 1 000 mm: +5,0 mm; for d = 1 200 mm to 1 600 mm: +6,0 mm. bThe di

48、mensions in brackets are restricted tolerances on the mean outside diameter for electrofusion welding: +0,006 d rounded up to the nearest 0,1 mm, at least 0,3 mm. cThe values given have been calculated as follows: tolerance on out-of-roundness: Straight pipes: d 75 mm: 0,008 d + 1 mm, rounded up to the ne