CEPT ETS 300 718-1-1999 Radio Equipment and Systems (RES) Avalanche Beacons Transmitter - Receiver Systems Part One Application Form《无线电设备和系统(RES)雪崩信标机 发射器 接收器系统 第1部分 申请表》.pdf

《CEPT ETS 300 718-1-1999 Radio Equipment and Systems (RES) Avalanche Beacons Transmitter - Receiver Systems Part One Application Form《无线电设备和系统(RES)雪崩信标机 发射器 接收器系统 第1部分 申请表》.pdf》由会员分享，可在线阅读，更多相关《CEPT ETS 300 718-1-1999 Radio Equipment and Systems (RES) Avalanche Beacons Transmitter - Receiver Systems Part One Application Form《无线电设备和系统(RES)雪崩信标机 发射器 接收器系统 第1部分 申请表》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 STD-CEPT ETS 300 718-1-ENGL 1179 II 232bilLil 001bL51 859 Application form for testing to ETS 300 718 Radio Equipment and Systems (RES) Avalanche Beacons; Transmitter - receiver systems The submission documentation to a National Regulatory Body for Type approval purposes shall consist of two parts;

2、 Part one. Application Form Part two. Test report form Important copyright notice: No modification whatsoever of any part of the text of this Application Form may be made. The only amendments permissible in reproduction are modifications to the layout, enlargement of the field or the addition of log

3、os of test laboratories making use of this form. Version: 09/99 Approved by WG RR: September 1999 Published by: European Radiocommunications Off ice Midtermolen 1 DK-2100 Copenhagen Denmark Telephone: +45 35 25 03 O0 Telefax: +4535250330 E-mail: ero ero .dk Web Site: http:/w.ero.dk APPLICATION FORM

4、FOR TESTING TO ETS 300 718 The application form shall be used for equipment submitted for type testing in accordance with ETS 300 718. Avalanche beacons are radio location systems used for searching for and/or finding avalanche victims, for the purpose of direct rescue. The systems comprise a transm

5、itter as well as a receiver part. The application form shall be completed by the applicant and submitted to a test laboratory accredited in accordance with EN45001 or IS0 guide 25 or a national standard conforming to EN45001 or IS0 guide 25. PLEASE READ THE FOLLOWING NOTES: Note (a) More than one it

6、em of equipment may be required to be submitted for type testing where an equipment needs to be modified to provide connections to facilitate testing, .e. measurements requiring direct connections to be made. In such cases a second un-modified equipment may be required for radiated .e. case or cabin

7、et radiation or ERP (effective radiated power) measurements to be perfomed. Full details of modifications are to be provided, where applicable. Note (b) On non-hamonised parameters, national administrations may impose conditions on the type of modulation, channevfrequency separations, temperature ra

8、nge, maximum transmitter output power/eff ective radiated power, equipment marking and the inclusion of an automatic transmitter shut-off facility as a condition for the issue of an individual or general licence or as a condition for the use under licence exemption. Manufacturers producing equipment

9、 to ETS 300 718 may wish to offer an equipment of the same basic design in a number of different forms with different RF characteristics. This is subsequently referred to as a family of equiprnents. Each equipment in the family must be given a unique Type Designation. Eauipment with differina option

10、al features If an applicant wishes to obtain type approval, on the basis of a single set of test results for a family of equipments derived from the same basic design, where the equipments in the family have different operational features, such as audio output powers, which are not a requirement of

11、ETS 300 71 8 then the following considerations shall be observed. Any operational feature in hardware or software, which can effect any of the performance parameters (not including signalling), shall be clearly defined by the applicant at the time of application. This will enable the National Regula

12、tory Authority to determine whether further testing is needed. 1 Note Cc) ACCESSORIES It is the applicants responsibility wh- submitting equipment(s) to the test laboratory to provide appropriate connectors or alternative coupling arrangements to facilitate the connection of test equipment by the te

13、st laboratory to the equipment under test (E.U.T.). This should enable, if applicable: i) i) iii) iv) v) access to the equipment RF output (transmitter); operation of the equipment to transmit (transmitter); access to the equipment modulator input; access to the analogue output of the RF part; coupl

14、ing arrangement (e.g. optical or acoustic coupling for equipment having no external audio connection); means of connecting the equipment to an external power supply. means of turning the modulation and signalling on/off. vi) vi) Note (d) For type approval to be granted on the basis of tests conducte

15、d on a pre-producti n model, that model must be manufactured to the same production drawings and manufacturers specification as the later production models. Where this is not the case the national regulatory authority reserves the right to require either partial or full type testing to be carried ou

16、t on the final production models. Note (e) It is the applicants responsibility to ensure that the equipment meets all the regulatory requirements for marking in the country where type approval is being sought. I APPLICANI! S DETAILS I CATEGORY OF APPLICANT (please tick relevant box opposite) (a) 0 M

17、ANUFACTURER (b) 0 IMPORTER (Cl 0 DISTRIBUTOR (d) 0 AGENT COMPANY NAME ADDRESS . . NAME FOR CONTACT PURPOSES TELEPHONE NO: . FAX No: . E-MAIL: . If box (a) is ticked and the equipment is manufactured at a different address to that of the applicant, or if box (b), (c) or (d) is ticked, complete detail

18、s in the box below with respect to the manufacturer. MA“FACTRERS DETAILS COMPANY NAME ADDRESS . . . NAME FOR CONTACT PURPOSES TELEPHONE NO: . FAX NO: . E-MAIL: . _ INTENDED USE (For information only) Details . Product brochures included Yes o No 3 - TYPE DESIGNATION (See Note 1) The type designation

19、 may be either a single alphanumeric code an alphanumeric/code divided into two parts. Please fill in OR TYPE DESIGNATION IN TWO PARTS: Note 1 This is the manufacturers numeric or alphanumeric code or name that is specific to a particular equipment. It may contain information in coded form on the ch

20、aracteristics of the equipment e.g. frequency, power. The manufacturer is free to choose the form of the type designation. This is the number, code or trade name used by the manufacturer to describe a series or family of equipment of substantially the same mechanical and electrical construction whic

21、h will include a number of related equipments. This number is often referred to as the “model no.“. Note 2 Note 3 This is the manufacturers identification number given to a specific equipment in the series or family of equipments. It is often referred to as the “identification number“. TYPE APPROVAL

22、 TO OTHER ETC Has the equipment been previously type approved to any other ETS or I- ETS ? Yes 0 If Yes please provide details of the previous type approval. (i.e. Type numbers, Dates, Issuing Authority, continue on separate sheet if required) . . 4 STD.CEPT ETS 300 718-1-ENGL It999 = 232bqLLi bbL5b

23、 330 m EXTREME T-ERA- RANGE (over which equipment is to be type tested) General Other -30 OC to +45 OC . TRANSMITTER TECHNICAL CHARACTERISTICS Type +-+ Type 1: f = 457 kHz +-+ +-+ Type 2: f = 2 275 Hz and f= 457 IcHz (See ETS 300 718 sub-clause 4.2.8) FREQUENC CHARACTERISTICS Method of frequency gen

24、eration +-+ CRYSTAL +-+ +-+ SYNTHESIZER +-+ +-+ +-+ OTHER ,. . ,. . ,. . 5 STDmCEPT ETS 300 71B-L-ENGL 1999 232bli1I 00LbL57 277 = TRANSM1“ER RF CARRIER CHARACTERISTICS MAXIMUM RATED TRANSMITTER OUTPUT dB(pA/m) Field strength at 10m (FOR CLASS EQUIPMENT WITH INTEGRAL ANTENNA) Is transmitter carrier

25、output variable? +-+ Yes +-+ NO +-+ +-+ If Yes RF output Maximum . Is the RF output continuously variable or stepped If stepped . . -. . dB per step Minimum . Amps/dEi(p?i/m) +-+ Yes +-+ +-+ Yes +-+ +-+ NO +-+ +-+ +-+ No BATTERY +-+ Nickel Cadmium +-+ Lead acid +-+ Leclanch +-+ Lithium +-+ Other Det

26、ails: . Extreme test voltages +-+ +-+ +-+ +-+ +-+ . DC (VI . Nominal DC Voltage (V) DC Maximum Current (A) 6 FREQUENCY IDENTIFICATION Each equipment, whether one or more submitted for tests shall carry clear identification (such as a serial number), together with the frequency identification display

27、ed on the equipment. Trancmi t Nominal Frequency (MHZ 1 Equipment identification e.g. serial number Receive Nominal Frequency (MHZ 1 7 Spare batteries e. g . (portable equipment 1 +-+ +-+ Yes +-+ +-+ No No No No Battery charging device +-+ Yes +-+ +-+ +-+ Special tools for dismantling equipment +-+

28、Yes +-+ +-+ +-+ Test fixture (if applicable) Yes +-+ +-+ +-+ +-+ Full equipment documentation: Operating instructions +-+ Yes +-+ +-+ NO +-+ User manual +-+ Yes +-+ +-+ NO +-+ Circuit diagrams +-+ Yes +-+ +-+ NO +-+ P.C. board layout, including component positioning +-+ Yes +-+ NO +-+ +-+ Parts list

29、 Other +-+ +-+ Yes +-+ +-+ NO +-+ Yes +-+ +-+ No +-+ If Yes, please specify 8 DECLARATION Are the equipments submitted representative production models? +-+ Yes +-+ +-+ NO +-+ If not are the equipments pre-production models? I +-+ Yes +-+ +-+ NO +-+ If pre-production equipments are submitted will th

30、e final production equipments be identical in respects with the equipment tested +-+ Yes +-+ +-+ NO +-+ If no, supply full details of differences: I I hereby declare that I am entitled to sign on behalf of the applicant and that the information supplied is correct and complete. Signature Name Position held Date 9