CAN CSA-C22 2 NO 60335-2-34-2013 Safety of Household and Similar Electrical Appliances - Part 2-34 Particular Requirements for Motor-Compressors (First Edition).pdf

《CAN CSA-C22 2 NO 60335-2-34-2013 Safety of Household and Similar Electrical Appliances - Part 2-34 Particular Requirements for Motor-Compressors (First Edition).pdf》由会员分享，可在线阅读，更多相关《CAN CSA-C22 2 NO 60335-2-34-2013 Safety of Household and Similar Electrical Appliances - Part 2-34 Particular Requirements for Motor-Compressors (First Edition).pdf（76页珍藏版）》请在麦多课文档分享上搜索。

1、Safety of Household and Similar Electrical Appliances Part2-34: Particular Requirements for Motor-CompressorsCAN/CSA-C22.2 No. 60335-2-34-13(IEC 60335-2-34:2002+A1:2004+A2:2008, MOD)National Standard of CanadaNOT FOR RESALE. / PUBLICATION NON DESTINE LA REVENTE.Legal Notice for StandardsCanadian Sta

2、ndards Association (operating as “CSA Group”) develops standards through a consensus standards development process approved by the Standards Council of Canada. This process brings together volunteers representing varied viewpoints and interests to achieve consensus and develop a standard. Although C

3、SA Group administers the process and establishes rules to promote fairness in achieving consensus, it does not independently test, evaluate, or verify the content of standards.Disclaimer and exclusion of liabilityThis document is provided without any representations, warranties, or conditions of any

4、 kind, express or implied, including, without limitation, implied warranties or conditions concerning this documents fitness for a particular purpose or use, its merchantability, or its non-infringement of any third partys intellectual property rights. CSA Group does not warrant the accuracy, comple

5、teness, or currency of any of the information published in this document. CSA Group makes no representations or warranties regarding this documents compliance with any applicable statute, rule, or regulation. IN NO EVENT SHALL CSA GROUP, ITS VOLUNTEERS, MEMBERS, SUBSIDIARIES, OR AFFILIATED COMPANIES

6、, OR THEIR EMPLOYEES, DIRECTORS, OR OFFICERS, BE LIABLE FOR ANY DIRECT, INDIRECT, OR INCIDENTAL DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES, HOWSOEVER CAUSED, INCLUDING BUT NOT LIMITED TO SPECIAL OR CONSEQUENTIAL DAMAGES, LOST REVENUE, BUSINESS INTERRUPTION, LOST OR DAMAGED DATA, OR ANY OTHER COMMERCI

7、AL OR ECONOMIC LOSS, WHETHER BASED IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR ANY OTHER THEORY OF LIABILITY, ARISING OUT OF OR RESULTING FROM ACCESS TO OR POSSESSION OR USE OF THIS DOCUMENT, EVEN IF CSA GROUP HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES.In

8、publishing and making this document available, CSA Group is not undertaking to render professional or other services for or on behalf of any person or entity or to perform any duty owed by any person or entity to another person or entity. The information in this document is directed to those who hav

9、e the appropriate degree of experience to use and apply its contents, and CSA Group accepts no responsibility whatsoever arising in any way from any and all use of or reliance on the information contained in this document. CSA Group is a private not-for-profit company that publishes voluntary standa

10、rds and related documents. CSA Group has no power, nor does it undertake, to enforce compliance with the contents of the standards or other documents it publishes. Intellectual property rights and ownershipAs between CSA Group and the users of this document (whether it be in printed or electronic fo

11、rm), CSA Group is the owner, or the authorized licensee, of all works contained herein that are protected by copyright, all trade-marks (except as otherwise noted to the contrary), and all inventions and trade secrets that may be contained in this document, whether or not such inventions and trade s

12、ecrets are protected by patents and applications for patents. Without limitation, the unauthorized use, modification, copying, or disclosure of this document may violate laws that protect CSA Groups and/or others intellectual property and may give rise to a right in CSA Group and/or others to seek l

13、egal redress for such use, modification, copying, or disclosure. To the extent permitted by licence or by law, CSA Group reserves all intellectual property rights in this document.Patent rightsAttention is drawn to the possibility that some of the elements of this standard may be the subject of pate

14、nt rights. CSA Group shall not be held responsible for identifying any or all such patent rights. Users of this standard are expressly advised that determination of the validity of any such patent rights is entirely their own responsibility.Authorized use of this documentThis document is being provi

15、ded by CSA Group for informational and non-commercial use only. The user of this document is authorized to do only the following:If this document is in electronic form:sLOADTHISDOCUMENTONTOACOMPUTERFORTHESOLEPURPOSEOFREVIEWINGITsSEARCHANDBROWSETHISDOCUMENTANDsPRINTTHISDOCUMENTIFITISIN0$ this remains

16、 the continuing responsibility of the SDO. An NSC reflects a consensus of a number of capable individuals whose collective interests provide, to the greatest practicable extent, a balance of representation of general interests, producers, regulators, users (including consumers), and others with rele

17、vant interests, as may be appropriate to the subject in hand. It normally is a standard which is capable of making a significant and timely contribution to the national interest.Those who have a need to apply standards areencouraged to use NSCs. These standards are subjectto periodic review. Users o

18、f NSCs are cautionedto obtain the latest edition from the SDO which publishes the standard.The responsibility for approving standards as National Standards of Canada rests with theStandards Council of Canada270 Albert Street, Suite 200Ottawa, Ontario, K1P 6N7CanadaAlthough the intended primary appli

19、cation of this Standard is stated in its Scope, it is importantto note that it remains the responsibility of the users to judge its suitability for their particular purpose.TMA trade-mark of Canadian Standards Association, operating as “CSA Group”Cette norme est offerte en anglais seulement pour le

20、moment. Le Groupe CSA publiera la versionen franais ds quelle sera produite par lorganisme rdacteur.National Standard of CanadaPrepared byInternational Electrotechnical CommissionSafety of Household and Similar Electrical Appliances Part2-34: Particular Requirements for Motor-CompressorsReviewed byA

21、ssociation of Standardization andCertificationNMX-J-521/2-34-ANCEFirst EditionUnderwriters Laboratories Inc.UL 60335-2-34Fifth EditionApproved byStandards Council of CanadaCSA GroupCAN/CSA-C22.2 No. 60335-2-34-13First Edition(IEC 60335-2-34:2002+A1:2004+A2:2008, MOD)ANSI/UL 60335-2-34-2013March 22,

22、2013This national standard is based on publication IEC 60335-2-34, Edition 4.2:2008(Edition 4:2002 consolidated with amendment 1:2004 and amendment 2:2008).Commitment for AmendmentsThis standard is issued jointly by the Association of Standardization and Certification (ANCE), theCanadian Standards A

23、ssociation (operating as “CSA Group”), and Underwriters Laboratories Inc. (UL).Comments or proposals for revisions on any part of the standard may be submitted to ANCE, CSAGroup, or UL at anytime. Revisions to this standard will be made only after processing according to thestandards development pro

24、cedures of ANCE, CSA Group, and UL. CSA Group and UL will issuerevisions to this standard by means of a new edition or revised or additional pages bearing their dateof issue. ANCE will incorporate the same revisions into a new edition of the standard bearing the samedate of issue as the CSA Group an

25、d UL pages.Copyright 2013 ANCERights reserved in favor of ANCE.ISBN 978-1-55491-972-7 2013 CSA GroupAll rights reserved. No part of this publication may be reproduced in any form whatsoever without theprior permission of the publisher.This Standard is subject to periodic review, and suggestions for

26、its improvement will be referred to theappropriate committee. To submit a proposal for change, please send the following information toinquirescsagroup.org and include Proposal for change in the subject line: Standard designation(number); relevant clause, table, and/or figure number; wording of the

27、proposed change; and rationalefor the change.To purchase CSA Group Standards and related publications, visit CSA Groups Online Store atshop.csa.ca or call toll-free 1-800-463-6727 or 416-747-4044.Copyright 2013 Underwriters Laboratories Inc.ULs Standards for Safety are copyrighted by UL. Neither a p

28、rinted nor electronic copy of a Standardshould be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regardingthose Standards shall remain the sole and exclusive property of UL.This ANSI/UL Standard for Safety consists of the Fifth Edition. The most recent designatio

29、n of ANSI/UL60335-2-34 as an American National Standard (ANSI) occurred on March 22, 2013. ANSI approval fora standard does not include the Cover Page, Transmittal Pages, Title Page (front and back), or thePreface. The National Difference Page and IEC Foreword are also excluded from the ANSI approva

30、l ofIEC-based standards.Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time.Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative StandardsDevelopment System (CSDS) at http:/.To purchase UL Standards, visit Comm 2000 at http:

31、/m- call toll-free 1-888-853-3503.CONTENTSPreface .5NATIONAL DIFFERENCES .8FOREWORD 9INTRODUCTION .121 Scope 142 Normative references .153 Definitions 164 General requirement .185 General conditions for the tests 186 Classification 207 Marking and instructions 218 Protection against access to live p

32、arts 219 Starting of motor-operated appliances 2110 Power input and current .2211 Heating 2212 Void .2213 Leakage current and electric strength at operating temperature 2214 Transient overvoltages 2215 Moisture resistance .2216 Leakage current and electric strength .2217 Overload protection of trans

33、formers and associated circuits 2218 Endurance .2219 Abnormal operation .2320 Stability and mechanical hazards .3021 Mechanical strength .3022 Construction .3023 Internal wiring 3524 Components .3625 Supply connection and external flexible cords 3726 Terminals for external conductors .3727 Provision

34、 for earthing 3728 Screws and connections .3729 Clearances, creepage distances and solid insulation 3730 Resistance to heat and fire 3831 Resistance to rusting 3832 Radiation, toxicity and similar hazards .39MARCH 22, 2013 NMX-J-521/2-34-ANCE CAN/CSA-C22.2 NO. 60335-2-34-13 UL 60335-2-34 3AnnexesAnn

35、ex C (normative) Aging test on motorsAnnex D (normative) Alternative requirements for protected motor unitsAnnex AA (normative) Running overload tests for motor-compressors classified as tested withAnnex AAAnnex DVA (informative) Component Standards Cross ReferenceAnnex 101.DVBB (normative) Accelera

36、ted Aging Tests GasketsAnnex 101.DVCC Refrigeration Code (informative)Annex 101.DVDD (normative) Nonmetallic Materials101.DVDD.1 General 57101.DVDD.2 Electrical properties .57101.DVDD.3 Mechanical properties .57101.DVDD.4 Thermal properties 58101.DVDD.5 Ultraviolet light exposure .58Annex 101.DVEE (

37、normative) Bypass valve testingAnnex 101.DVFF (informative) Supplemental requirementsAnnex 101.DVGG (informative) Optional Fatigue Test101.DVGG.5 Fatigue cycle test specification .61Annex 101.DVHH (informative) Maximum Continuous Current TestBibliographyMARCH 22, 2013NMX-J-521/2-34-ANCE CAN/CSA-C22.

38、2 NO. 60335-2-34-13 UL 60335-2-344PrefaceThis is the harmonized ANCE, CSA Group, and UL standard for particular requirements formotor-compressors. It is the first edition of NMX-J-521/2-34-ANCE, the first edition of CAN/CSA-C22.2No. 60335-2-34, and the fifth edition of UL 60335-2-34. This edition of

39、 UL 60335-234 supersedes theprevious edition(s) published in March, 2004. This Standard is based on the Standard for Safety ofHousehold and Similar Electrical Appliances, Part 2-34: Particular Requirements for Motor-Compressors,IEC Publication 60335-234, edition 4.2.In Canada, for general informatio

40、n on the Standards of the Canadian Electrical Code, Part II, see thepreface of CAN/CSA-C22.2 No. 0.This harmonized standard was prepared by the Association of Standardization and Certification (ANCE),CSA Group, and Underwriters Laboratories Inc. (UL). The efforts and support of Industry Associations

41、Cmara Nacional de Manufacturas Elctricas (CANAME), the Heating, Refrigeration and Air ConditioningInstitute of Canada (HRAI), the Air-Conditioning, Heating, and Refrigeration Institute (AHRI), and theAssociation of Home Appliance Manufacturers (AHAM), and of the Technical HarmonizationSub-Committee

42、(THSC 61D TC1) of the Council on the Harmonization of Electrotechnical Standards ofthe Nations of the Americas (CANENA), are gratefully acknowledged.This standard is considered suitable for use for conformity assessment within the stated scope of thestandard.The present Mexican Standard was develope

43、d by the CT 61 from the Comite de Normalizacion de laAsociacion de Normalizacion y Certificacion, A.C., CONANCE with the collaboration of the heating,refrigeration and air conditioning manufacturers and users.This standard was reviewed by the CSA Subcommittee on Household Appliances for Refrigeratio

44、n, underthe jurisdiction of the CSA Technical Committee on Consumer and Commercial Products and the CSAStrategic Steering Committee on Requirements for Electrical Safety, and has been formally approved bythe CSA Technical Committee.This standard has been approved by the Standards Council of Canada (

45、SCC) as a National Standard ofCanada.This Standard has been approved by the American National Standards Institute (ANSI) as an AmericanNational Standard.Where reference is made to a specific number of samples to be tested, the specified number is to beconsidered a minimum quantity.Note: Although the

46、 intended primary application of this standard is stated in its scope, it is important to note thatit remains the responsibility of the users of the standard to judge its suitability for their particular purpose.Level of harmonizationThis standard adopts the IEC text with national differences. This

47、standard is published as an equivalentstandard for ANCE, CSA Group, and UL. An equivalent standard is a standard that is substantially thesame in technical content, except as follows: Technical national differences are allowed for codes andgovernmental regulations as well as those recognized as bein

48、g in accordance with NAFTA Article 905, forMARCH 22, 2013 NMX-J-521/2-34-ANCE CAN/CSA-C22.2 NO. 60335-2-34-13 UL 60335-2-34 5example, because of fundamental climatic, geographical, technological, or infrastructural factors, scientificjustification, or the level of protection that the country conside

49、rs appropriate. Presentation is word for wordexcept for editorial changes.All national differences from the IEC text are included in the ANCE, CSA Group, and UL versions of thestandard. While the technical content is the same in each organizations version, the format andpresentation may differ.It is the intent and obje