BS ISO 5483-2004 Ships and marine technology - Drain facilities from oil and water tanks《船舶和海上技术 油箱和水箱的排水设施》.pdf

《BS ISO 5483-2004 Ships and marine technology - Drain facilities from oil and water tanks《船舶和海上技术 油箱和水箱的排水设施》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 5483-2004 Ships and marine technology - Drain facilities from oil and water tanks《船舶和海上技术 油箱和水箱的排水设施》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 5483:2003 Ships and marine technology Drain facilities from oil and water tanks ICS 47.020.30 BS ISO 5483:2003 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 5 February 2004 BSI 5 February 2004 ISBN 0 580 43354 4 Nati

2、onal foreword This British Standard reproduces verbatim ISO 5483:2003 and implements it as the UK national standard. The UK participation in its preparation was entrusted by Technical Committee SME/32, Ships and marine technology, to Subcommittee SME/32/3, Ships and marine technology piping and mach

3、inery, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be found in the BSI Catalogue under the sec

4、tion entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.

5、Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor re

6、lated international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page pages ii to v, a blank page, pages 1 to 16, an inside back cover and a back cover. The BSI copyright notice displayed in this

7、 document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments Reference number ISO 5483:2003(E) OSI 3002INTERNATIONAL STANDARD ISO 5483 Second edition 2003-02-15 Ships and marine technology Drain facilities from oil and water tanks Navires et techn

8、ologie maritime quipement de vidange des rservoirs dhuile et deau BSISO5483:2003ISO 5483:2003(E) DPlcsid Fremia ihTs PDF file mya ctnoian emdebt dedyfepcaes. In ccacnadrow eitA hebods licnesilop gnic,y tihs file mirp eb yatnde iv roweb detu slahl ton ide ebtlnu deess teh typfecaes wihce era hml era

9、deddebicsnede ti dna onstlalde t noeh comuptfrep reromign tide ehtin.g In wodlnidaot gnihs fil,e trapise atpecc tiereht nser ehnopsiiblity fo nto ifnriigngn Aebods licnesilop gnic.y ehT ISO tneClar Secrteirata caceptl on siibality in this .aera Ai ebods a tedarmfo kra Aebod SystemI snctaropro.de teD

10、ials fo teh sfotwcudorp erats sut deo crtaee tihs PDF file cna f ebi dnuon tlareneG eh Ifnler oatit evt oeh file; tP ehDc-Frtaeino marapterew stpo ereimizde fro irptni.gn Evyre cera neeb sah takne tsne oeru taht teh file is siutlbae fosu re yb ISO memdob rebeis. In tlnu ehikletneve y ttah lborp aem

11、lertait gno it is f,dnuo plsaee ifnrom ttneC ehlar Secterirata ta teh serddaig sleb nevwo. ISO 3002 All irthgs erse.devr lnUeto sswrehise specified, on trap fo this lbupictaion maeb y cudorperro de tuilizi den yna form ro na ybm ynae,s lecetrinoc ro mceinahcla, incliduntohp gcoiypodna gn micrfoilm,

12、wittuoh repmissii now nritign from ietI rehSa Ot tsserdda eh ebolw or ISOs memreb i ydobn the cnuotfo yr ttseuqer ehe.r ISO cirypothg fofice saCe tsopale 65 eneG 1121-HC 02 av leT. 4 + 10 947 22 1 11 xaF0 947 22 14 + 9 74 E-mial coirypthgis.o gro We bwww.is.o groii ISO 3002 Allr ihgtsser edevrBSISO5

13、483:2003IS:3845 O3002(E) I SO 3002 All irhgts seredevr iiiContents Page Foreword iv Introduction v 1 Scope 1 2 Normative references . 1 3 Designation 2 4 General assembly arrangement 2 4.1 Assembly . 2 4.2 Threads 3 4.3 Materials. 3 5 Mounting 4 5.1 Type A 4 5.2 Type B 6 5.3 General for Types A and

14、B. 8 6 Parts production . 8 6.1 Welding ring Type A. 8 6.2 Welding ring Type B. 10 7 Drain screws 11 7.1 For water tanks Type A 11 7.2 For water tanks Type B 12 7.3 For oil tanks Type A . 14 7.4 For oil tanks Type B . 15 8 Marking and location 16 BSISO5483:2003IS:3845 O3002(E) iv I SO 3002 All irhgt

15、s seredevrForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for

16、 which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on a

17、ll matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are

18、 circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held re

19、sponsible for identifying any or all such patent rights. ISO 5483 was prepared by Technical Committee ISO/TC 8, Ships and marine technology, Subcommittee SC 3, Piping and machinery. This second edition cancels and replaces the first edition (ISO 5483:1977), which has been technically revised. BSISO5

20、483:2003IS:3845 O3002(E) I SO 3002 All irhgts seredevr vIntroduction Throughout this International Standard, the minimum essential criteria are identified by the use of the key word “shall”. Recommended criteria are identified by the use of the key word “should”, and while not mandatory are consider

21、ed to be of primary importance in providing serviceable, economical and practical designs. Deviations from the recommended criteria should occur only after careful consideration, extensive testing and thorough service evaluation have shown alternative methods to be satisfactory. BSISO5483:2003BSISO5

22、483:2003INTENRATIONAL TSANDADR IS:3845 O3002(E)I SO 3002 All irhgts seredevr 1Ships and marine technology Drain facilities from oil and water tanks 1 Scope This International Standard specifies dimensions and materials for welding rings and drain screws situated at the bottom of oil and water tanks.

23、 Oil and water tanks occur as: built-in tanks, as an integrated part of the hull structure, and, detachable tanks, located in appropriate rooms and compartments. This standard covers facilities for both instances. 2 Normative references The following referenced documents are indispensable for the ap

24、plication of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 68, ISO general purpose screw threads Basic profile ISO 261, ISO general-purpose metric screw threads Genera

25、l plan ISO 683-13, Heat-treatable steels, alloy steels and free-cutting steels Part 13: Wrought stainless steels ISO 965-1, ISO general-purpose metric screw threads Tolerances Part 1: Principles and basic data ISO 965-2, ISO general purpose metric screw threads Tolerances Part 2: Limits of sizes for

26、 general purpose external and internal screw Medium quality ISO 965-3, ISO general purpose metric screw threads Tolerances Part 3: Deviations for constructional screw threads ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indications

27、BSISO5483:20031IS:3845 O3002(E) 2 I SO 3002 All irhgts seredevr3 Designation For the purposes of this International Standard, two types of drain facilities are covered: Type A, which is universally applicable, especially where flush mounting with the outer surface of hull-plating at any plate thickn

28、ess is required, and Type B, which is usable in all other instances where the above-mentioned requirement is not applicable. NOTE Both Type A and Type B arrangements are identified by the following two categories of drain plugs: square wrench connection for water tanks, and hexagonal wrench connecti

29、on for oil tanks. 4 General assembly arrangement 4.1 Assembly For Type A, refer to Figure 1 and Table 1. For Type B, refer to Figure 2 and Table 2. NOTE The extreme left and right sections represent hull plating. Figure 1 General arrangement for Type A Table 1 Parts list for Type A Part No. Part nam

30、e Size 162 mm 1 Welding ring 350 mm M42 2 2 Drain screw M72 3 3 Gasket BSISO5483:20032IS:3845 O3002(E) I SO 3002 All irhgts seredevr 3NOTE The extreme left and right sections represent hull plating. Figure 2 General arrangement for Type B Table 2 Parts list for Type B Part No. Part name Size 8 mm 15

31、 mm 1 Welding ring 22 mm M42 2 2 Drain screw M72 3 3 Gasket 4.2 Threads For both types, the threads shall be in accordance with ISO 68-1, ISO 261 and ISO 965-1, ISO 965-2 and ISO 965-3. NOTE A non-toxic anti-seize compound grease may be used on the thread surfaces. 4.3 Materials The welding ring, dr

32、ain screw and gasket materials should be as given in Table 3. Other materials shall be of equivalent quality and in all respects suitable for the intended purpose. Table 3 Material list for both types Component Material Designation Welding ring Steel. To be of similar quality as surrounding tank bot

33、tom steel plating Shipbuilding steel Stainless steel ISO 683-13 Austenitic steel Type 20A Drain screw Copper-aluminium alloy Hackle flax Gasket Lead compound, soft hemp packing or equivalent BSISO5483:20033IS:3845 O3002(E) 4 I SO 3002 All irhgts seredevr5 Mounting 5.1 Type A For Type A mountings, se

34、e Figures 1, 3, 4 and Table 4. For parts identification, see Table 1. a) Type A.1 mounting (see Table 4) b) Type A.2 mounting (see Table 4) aInner side of bottom plate Figure 3 Type A mounting (see Table 1 for parts identification) BSISO5483:20034IS:3845 O3002(E) I SO 3002 All irhgts seredevr 5Table

35、 4 Main dimensions for Type A assembly Dimensions in millimetres Size Type d t 162 A-1 165 u 27,5 350 A-2 353 W 27,5 u 38 NOTE For detailed dimensions, see Figure 8 and Table 6. NOTE 1 Ensure that alternate sections of the circumference are welded in sequence as shown to avoid heat deformation. Weld

36、 the 90 shown as “1”, skip 90, then weld section “2.” Skip 180 and weld section “3.” Skip 90 and weld section “4,” the last section. NOTE 2 Completed welding to be examined for cracks, see 5.3. Figure 4 Welding sequence BSISO5483:20035IS:3845 O3002(E) 6 I SO 3002 All irhgts seredevr5.2 Type B For Ty

37、pe B mountings, see Figures 2, 5, 6, 7 and 9, and Table 5. Dimensions in millimetres aSection A-A R3 max bHole in the bottom plating. Figure 5 For plate thickness 8 mm up to 14,5 mm (see Table 2 for description of 1 to 3) Table 5 Main dimensions for Type B assembly Dimensions in millimetres Size Typ

38、e h 2d 135 B-1 35 M 42 2 40 B-2 40 M 72 3 NOTE For dimensions references, see Figure 9 and Table 7. BSISO5483:20036IS:3845 O3002(E) I SO 3002 All irhgts seredevr 7Dimensions in millimetres NOTE For other dimensions and details, see Figures 5 and 9. Figure 6 For plate thickness 15 mm to 21,5 mm BSISO

39、5483:20037IS:3845 O3002(E) 8 I SO 3002 All irhgts seredevrDimensions in millimetres NOTE For other dimensions and details, see Figures 5 and 9. Figure 7 For plate thickness 22 mm and beyond 5.3 General for Types A and B For welding, compliance with the rules of classification societies shall be obse

40、rved. See Figure 4. 6 Parts production 6.1 Welding ring Type A Details of Type A welding rings are given in Figure 8 and Table 6. The drain screw and welding ring shall conform to the details of Figures 8 and 10. BSISO5483:20038IS:3845 O3002(E) I SO 3002 All irhgts seredevr 9Dimensions in millimetre

41、s No sharp edges Figure 8 Type A welding ring (see Table 6 for main dimensions) Table 6 Designations for welding rings in Type A drain facilities for water tanks Dimensions in millimetres Type l 1l 2l 3D 1D 2Mass kg A-1.1 A-1.2 6 10 3 10 18 12 110 128 162 8,2 A-2.1 A-2.2 6 10 3 10 18 12 298 315 350

42、16,8 NOTE For Type A, an M42 2 thread may be utilized, see ISO 965-1 and ISO 965-2. BSISO5483:20039IS:3845 O3002(E) 10 I SO 3002 All irhgts seredevr7H in Figure 8 represent the allowable tolerance of the nut minor diameter, which is 0,475 0 mm + , and the tolerance of the nut pitch diameter which is

43、 0,3 0 mm + . 8g in Figure 8 represents the allowable tolerance of the bolt major diameter, which is 0,038 0,488 mm , and the tolerance of the bolt pitch diameter, which is 0,038 0,318 mm . Tolerances: ISO 2768-1, designation m. Description: Designation - ISO No. - Type - D 2EXAMPLE Welding ring - I

44、SO 5483 - A 2.2 - 350 6.2 Welding ring Type B For details of Type B welding rings, see Figure 9 and Table 7. Dimensions in millimetres Slit for h 1= 22 mm aR3 max. Figure 9 Type B welding ring cross-section and overhead view BSISO5483:200310IS:3845 O3002(E) I SO 3002 All irhgts seredevr 11Table 7 Di

45、mensions for Type B welding rings Dimensions in millimetres Thread d 1h 1Female thread ad 4h 2t Mass kg Major diameter Minor diameter 8 6,9 M42 2 15 41,201 40,335 57 35 10 6,6 22 6,5 8 7,0 M72 3 15 70,551 69,252 92 40 13 6,8 22 6,6 aThese diameters are 0,5 mm bigger than stated in ISO 965. Descripti

46、on: Designation - ISO No. - Thread (d 1 ) - h 1EXAMPLE Welding ring - ISO 5483 - M42 2 - 15. 7 Drain screws 7.1 For water tanks Type A For details of drain screws for water tanks of Type A, see Figure 10. BSISO5483:200311IS:3845 O3002(E) 12 I SO 3002 All irhgts seredevrDimensions in millimetres Figu

47、re 10 Drain screws (see also Figure 8) NOTE For Type A - M72 3 may be utilized, see ISO 965-1 and ISO 965-2. Description: Designation - ISO No. - Type - W - Thread EXAMPLE Screw - ISO 5483 - A - W - M72 3. 7.2 For water tanks Type B For details of drain screws for water tanks of Type B, see Figure 1

48、1 and Table 8. BSISO5483:200312IS:3845 O3002(E) I SO 3002 All irhgts seredevr 13Dimensions in millimetres aThread undercut ISO Figure 11 Drain screws for water tanks, Type B Designation of a screw (D) with thread d 1= M42 2: Description: Designation - ISO No. - Type - W - Thread. EXAMPLE Plug - ISO 5483 - B - W - M42 2. BSISO5483:200313IS:3845 O3002(E) 14 I SO 3002 All irhgts seredevrTable 8 Details for Type B drain plugs in water tanks Thread d 1d 2d 3e h 3h 4h 5h 6s Mass D12 H11 kg M42 2 55 32 30,6 40 20 7 6 26 0,55 M72 3 90 38 36,6 45 25 10 5 32 1,25 7.3 For