BS ISO 491-2002 Cinematography - 35 mm motion-picture film and magnetic film - Cutting and perforating dimensions《电影摄影 35mm电影胶片和磁膜 剪切和穿孔尺寸》.pdf

《BS ISO 491-2002 Cinematography - 35 mm motion-picture film and magnetic film - Cutting and perforating dimensions《电影摄影 35mm电影胶片和磁膜 剪切和穿孔尺寸》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 491-2002 Cinematography - 35 mm motion-picture film and magnetic film - Cutting and perforating dimensions《电影摄影 35mm电影胶片和磁膜 剪切和穿孔尺寸》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 491:2002 Cinematography 35 mm motion-picture film and magnetic film Cutting and perforating dimensions ICS 37.060.20 BS ISO 491:2002 This British Standard, having been prepared under the direction of the Consumer Products and Services Sector Policy and Strategy Committee, was

2、 published under the authority of the Standards Policy and Strategy Committee on 20 August 2002 BSI 20 August 2002 ISBN 0 580 40290 8 National foreword This British Standard reproduces verbatim ISO 491:2002 and implements it as the UK national standard. It supersedes BS ISO 491:1995 which is withdra

3、wn. The UK participation in its preparation was entrusted to Technical Committee CPW/36, Cinematography, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement internat

4、ional publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include

5、all the necessary provisions of a contract. Users are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiri

6、es on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii and iii, a blank p

7、age, pages 1 to 7 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments Reference number ISO 491:2002(E)INTERNATIONAL STANDARD ISO 491 Sixth edition 2002-08-01 Cinematography 35 mm m

8、otion-picture film and magnetic film Cutting and perforating dimensions Cinmatographie Film cinmatographique et magntique de 35 mm Dimensions de coupe et de perforation BSISO491:2002BSISO491:2002iiIS:194 O2002(E) I SO 2002 All irthgs ersedevr iiiForeword ISO (the International Organization for Stand

9、ardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right

10、to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International St

11、andards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an I

12、nternational Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent r

13、ights. ISO 491 was prepared by Technical Committee ISO/TC 36, Cinematography. This sixth edition cancels and replaces the fifth edition (ISO 491:1995), which has been technically revised. Annex A forms a normative part of this International Standard. Annex B is for information only. BSISO491:2002iii

14、INTENRATIONAL TSANDADR IS:194 O2002(E)I SO 2002 All irthgs ersedevr 1Cinematography 35 mm motion-picture film and magnetic film Cutting and perforating dimensions 1 Scope This International Standard specifies the cutting and perforating dimensions for 35 mm unexposed motion-picture film and 35 mm ma

15、gnetic film, and the types of perforations used. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publ

16、ications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to a

17、pplies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 554:1976, Standard atmospheres for conditioning and/or testing Specifications ISO 18906:2000, Imaging materials Photographic films Specifications for safety film 3 Conditions for the measurement of dime

18、nsions The dimensions and tolerances specified in this International Standard apply at the time of manufacture, measured under atmospheric conditions of (23 1) C and (50 5) % relative humidity, as specified in ISO 554 1) . A manufacturer may indicate other nominal temperatures and humidity under whi

19、ch dimensions apply. 4 Dimensions 4.1 Dimensions of motion-picture film The dimensions shall be as shown in Figures 1 and 2 and given in Table 1. They apply to unexposed motion- picture and magnetic film which conform to ISO 18906. These specifications apply at the time of cutting and perforating. 4

20、.2 Dimensions of magnetic film With regard to 35 mm magnetic films, the dimensions which apply are those specified in Table 1 under the designation “Type P” with a perforation pitch B and the length of any 100 consecutive intervals L. 1) All measuring instrument calibrations should be referred to a

21、temperature of 20 C (as specified in 1) and a relative humidity of 50 %. BSISO491:20021IS:194 O2002(E) 2 I SO 2002 All irthgs ersedevr Table 1 Dimensions in millimetres Dimension Type P Type N Type DH A 34,975 0,025 34,975 0,025 34,975 0,025 B 4,75 0,01 4,75 0,01 4,75 0,01 B 4,74 0,01 4,74 0,01 C 2,

22、794 0,010 2,794 0,010 2,794 0,010 D 1,981 0,010 1,854 0,010 1,854 0,010 E 2,01 0,05 2,01 0,05 2,01 0,05 F 28,17 0,03 28,17 0,03 28,17 0,03 G 0,025 max. 0,025 max. 0,025 max. H 2,08 nom. R 0,50 0,03 0,13 max. 0,33 0,03 L 475,00 0,38 475,00 0,38 475,00 0,38 L 474,00 0,38 474,00 0,38 NOTE 1 While curre

23、nt usage is that type N perforations may be used for camera and intermediate films and type P perforations for print films, the long-term objective should be for all 35 mm films to have type P perforations. NOTE 2 Dimensions L and L represent the length of any 100 consecutive perforation intervals.

24、NOTE 3 Dimensions B and L (short perforation pitch) are provided to fulfil the requirements of continuous sprocket contact printing. NOTE 4 See annex A for full information concerning the same dimensions expressed in inches. BSISO491:20022IS:194 O2002(E) I SO 2002 All irthgs ersedevr 3Figure 1 Dimen

25、sions of 35 mm motion-picture film Figure 2 Types of perforation BSISO491:20023IS:194 O2002(E) 4 I SO 2002 All irthgs ersedevr Annex A (normative) Dimensions in inches The same dimensions as those in Table 1 can be expressed in inch units. These dimensions shall be as shown in Table A.1. Table A.1 D

26、imensions in inches Dimension Type P Type N Type DH A 1,377 0,001 1,377 0,001 1,377 0,001 B 0,187 0 0,000 4 0,187 0 0,000 4 0,187 0 0,000 4 B 0,186 6 0,000 4 0,186 6 0,000 4 C 0,110 0 0,000 4 0,110 0 0,000 4 0,110 0 0,000 4 D 0,078 0 0,000 4 0,073 0 0,000 4 0,073 0 0,000 4 E 0,079 0,002 0,079 0,002

27、0,079 0,002 F 1,109 0,001 1,109 0,001 1,109 0,001 G 0,001 max. 0,001 max. 0,001 max. H 0,082 nom. R 0,020 0,001 0,005 max. 0,013 0,001 L 18,700 0,015 18,700 0,015 18,700 0,015 L 18,660 0,015 18,660 0,015 NOTE The notes to Table 1 apply. BSISO491:20024IS:194 O2002(E) I SO 2002 All irthgs ersedevr 5An

28、nex B (informative) Additional data B.1 Uniformity of perforating The uniformity of pitch, hole size and margin (dimensions B or B, C, D and E) are important variables affecting image steadiness. Variations in these dimensions within a roll from one perforation to the next are more significant than

29、variations from roll to roll. In fact, it is the maximum variation from one set of four perforations to the next within any small group of consecutive perforations that is the most important variable. B.2 Dimensional stability During its life, film can shrink or swell due to changes in temperature o

30、r to loss or gain in moisture content. In addition, triacetate-based film can shrink due to the loss of solvents or plasticizers. These changes may result in changes in the dimensions. The change is generally uniform through the roll. B.3 Definition of low-shrinkage film Low-shrinkage film is film w

31、hich shrinks no more than 0,2 % from its original dimensions at the time of cutting and perforating, after the film has been: a) kept in the manufacturers normal commercial packing for six months at recommended storage conditions; b) exposed; c) processed and dried as recommended by the manufacturer

32、; d) stored in roll form, exposed to air, for a period not exceeding 30 d at 18 C to 24 C and 50 % to 60 % relative humidity. The film is measured under the same conditions of temperature and humidity as defined in clause 3. B.4 Choice of longitudinal pitch The choice of different pitch (B: long pit

33、ch, and B: short pitch), for original and print motion-picture films, depends on the necessity of printing and the type of printer used. In the most common type of printer, the original and print films move continuously over a printing sprocket. Consequently, the original film must be shorter In pit

34、ch than the print film in the approximate proportion of the thickness of the film to the radius of curvature of the printing sprocket. With current printing sprocket design, the value for this pitch differential is 0,3 %, with experience showing that a tolerance of 0,1 % is acceptable. With “Iow-shr

35、inkage” film base, it is common manufacturing practice to set the aim for the pitch of original films at a value of 0,2 % shorter than that of the films on which they will be printed. The additional shrinkage that occurs in the original film, because of processing and ageing before printing, should

36、result in the desired (0,3 0,1) % shorter pitch. BSISO491:20025IS:194 O2002(E) 6 I SO 2002 All irthgs ersedevr B.5 Effect of humidity It is a common tendency of the film to expand when exposed to high relative humidity. Allowance should be made for this factor in equipment design. BSISO491:20026IS:1

37、94 O2002(E) I SO 2002 All irthgs ersedevr 7Bibliography 1 ISO 1, Geometrical Product Specifications (GPS) Standard reference temperature for geometrical product specifications BSISO491:20027BS ISO 491:2002 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independ

38、ent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they p

39、ossess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the iden

40、tity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, internat

41、ional and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply

42、 the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI

43、 electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substan

44、tial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found

45、at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright,

46、Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standa

47、rd, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.