BS ISO 29262-2011 Production equipment for microsystems Interface between end effector and handling system《微系统用生产设备 操作系统和操作装置间接口》.pdf
《BS ISO 29262-2011 Production equipment for microsystems Interface between end effector and handling system《微系统用生产设备 操作系统和操作装置间接口》.pdf》由会员分享,可在线阅读,更多相关《BS ISO 29262-2011 Production equipment for microsystems Interface between end effector and handling system《微系统用生产设备 操作系统和操作装置间接口》.pdf(28页珍藏版)》请在麦多课文档分享上搜索。
1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 29262:2011Production equipment formicrosystems Interfacebetween end effector andhandling systemBS ISO 29262:2011 BRITISH STANDARDNational forewordThis British Standard is
2、the UK implementation of ISO 29262:2011.The UK participation in its preparation was entrusted to TechnicalCommittee MTE/1, Machine tools.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprov
3、isions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 65266 0ICS 25.040.99Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on
4、31 March 2011.Amendments issued since publicationDate Text affectedBS ISO 29262:2011Reference numberISO 29262:2011(E)ISO 2011INTERNATIONAL STANDARD ISO29262First edition2011-03-01Production equipment for microsystems Interface between end effector and handling system quipement de production pour sys
5、tmes microtechniques Interface entre outil et dispositif de manipulation BS ISO 29262:2011ISO 29262:2011(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which a
6、re embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorp
7、orated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that
8、 a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical
9、, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org
10、Published in Switzerland ii ISO 2011 All rights reservedBS ISO 29262:2011ISO 29262:2011(E) ISO 2011 All rights reserved iiiContents Page Foreword iv Introduction.v 1 Scope1 2 Normative references1 3 Terms and definitions .2 4 General .3 5 Interface definitions 4 5.1 Coordinate system 4 5.2 Layer 1 M
11、echanical interface.4 5.3 Layer 2 Service interface .8 5.4 Layer 3 Bus interface part11 5.5 Tolerances14 5.6 Load-bearing capacities .14 5.7 Designation 15 Annex A (normative) Tests procedure for fixation interface, pR.16 Bibliography17 BS ISO 29262:2011ISO 29262:2011(E) iv ISO 2011 All rights reser
12、vedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which
13、a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matt
14、ers of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circul
15、ated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsib
16、le for identifying any or all such patent rights. ISO 29262 was prepared by Technical Committee ISO/TC 39, Machine tools. BS ISO 29262:2011ISO 29262:2011(E) ISO 2011 All rights reserved vIntroduction This International Standard specifies requirements for an interface between end effector and handlin
17、g systems, or between functional modules in production equipment for microsystems. In production equipment for precision and microsystem technology, it is necessary for tools and end effectors to be replaced frequently because of small production runs. Interfaces for macroscopic handling systems, st
18、andardized according to ISO 9409-1 or ISO 9409-2 for instance, cannot be considered because of the small dimensions of the parts processed and, thus they are unsuitable for use as interface for end effectors and tools in micro and precision mechanics. This International Standard defines, in addition
19、 to the mechanical interface, the position and specification of the feedthroughs for fluidic and electrical coupling elements. An extra feature of this International Standard that differs from other standards in use is a central opening to permit the observation of the production or assembly process
20、. BS ISO 29262:2011BS ISO 29262:2011INTERNATIONAL STANDARD ISO 29262:2011(E) ISO 2011 All rights reserved 1Production equipment for microsystems Interface between end effector and handling system 1 Scope This International Standard specifies provisions for the interface between end effector and hand
21、ling systems in production equipment for microsystems. It specifies principal deviations, tolerances and designations for manually and automatically changeable end effectors. The aim is to specify the end effector interface in three levels with an increasing degree of specification. 2 Normative refe
22、rences The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 286-1, Geometrical product specificati
23、ons (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits ISO 286-2, Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts ISO 1101
24、, Geometrical Product Specifications (GPS) Geometrical tolerancing Tolerances of form, orientation, location and run-out ISO 3650, Geometrical Product Specifications (GPS) Length standards Gauge blocks ISO 8734:1997, Parallel pins, of hardened steel and martensitic stainless steel (Dowel pins) ISO 9
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSISO292622011PRODUCTIONEQUIPMENTFORMICROSYSTEMSINTERFACEBETWEENENDEFFECTORANDHANDLINGSYSTEM 系统 生产 设备

链接地址:http://www.mydoc123.com/p-586929.html