BS ISO 20203-2006 Carbonaceous materials used in the production of aluminium - Calcined coke - Determination of crystallite size of calcined petroleum coke by X-ray diffraction《铝生产.pdf

《BS ISO 20203-2006 Carbonaceous materials used in the production of aluminium - Calcined coke - Determination of crystallite size of calcined petroleum coke by X-ray diffraction《铝生产.pdf》由会员分享，可在线阅读，更多相关《BS ISO 20203-2006 Carbonaceous materials used in the production of aluminium - Calcined coke - Determination of crystallite size of calcined petroleum coke by X-ray diffraction《铝生产.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 20203:2005 Carbonaceous materials used in the production of aluminium Calcined of crystallite size of calcined petroleum coke by X-ray diffraction ICS 77.120.10 coke Determination BS ISO 20203:2005 This British Standard was published under the authority of the Standards Polic

2、y and Strategy Committee on 12 January 2006 BSI 12 January 2006 ISBN 0 580 47126 8 National foreword This British Standard reproduces verbatim ISO 20203:2005 and implements it as the UK national standard. The UK participation in its preparation was entrusted by Technical Committee CII/24, Raw materi

3、als for the aluminium industry, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European

4、developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be found in the BSI Catalogue under the se

5、ction entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.

6、 Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii to iv, pages 1 to 7 and a back cover. The BSI copyright notice displayed in this document indicat

7、es when the document was last issued. Amendments issued since publication Amd. No. Date Comments Reference number ISO 20203:2005(E)INTERNATIONAL STANDARD ISO 20203 First edition 2005-10-01 Carbonaceous materials used in the production of aluminium Calcined coke Determination of crystallite size of c

8、alcined petroleum coke by X-ray diffraction Produits carbons utiliss pour la production de laluminium Coke calcin Dtermination de la taille de la cristallite du coke calcin de ptrole par diffraction aux rayons X BS ISO 20203:2005ii BS ISO 20203:2005 iii Foreword ISO (the International Organization f

9、or Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has th

10、e right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Internat

11、ional Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication

12、 as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.

13、 ISO 20203 was prepared by Technical Committee ISO/TC 226, Materials for the production of primary aluminium. BS ISO 20203:2005 iv Introduction This International Standard is based on ASTM D5187-91(2002) 6published by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 1942

14、8-2959, United States. ASTM D5187-91(2002) was developed under the jurisdiction of ASTM Committee D02 on Petroleum Products and Lubricants as the direct responsibility of Subcommittee D02.05.0D on Petroleum Coke Sampling and Procedures, and was published in December 1991. The crystallinity of petrol

15、eum coke, as reflected by the L cvalue, is a general measure of quality affecting suitability for end use and is a function of the heat treatment used. The crystallite height is used to determine the extent of such heat treatment, for example, during calcination. The value of the L cdetermined is no

16、t affected by coke microporosity or the presence of foreign, non- crystalline materials such as dedust oil. 1 Carbonaceous materials used in the production of aluminium Calcined coke Determination of crystallite size of calcined petroleum coke by X-ray diffraction SAFETY PRECAUTIONS This Internation

17、al Standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1 Scope This Interna

18、tional Standard describes a test method for the determination of the mean crystallite height of a representative, pulverized sample of calcined petroleum coke by interpretation of an X-ray diffraction pattern produced through conventional X-ray scanning techniques. It applies to carbonaceous materia

19、ls used in the production of aluminium. Calcined petroleum coke contains crystallites of different heights. This test method covers the determination of the average height of all crystallites in the sample by empirical interpretation of the X-ray diffraction pattern. The crystallite diameter (L a )

20、is not determined by this test method. 2 Terms and definitions For the purposes of this document, the following terms, abbreviated terms and definitions apply. 2.1 crystallites stacks of graphitic carbon platelets located parallel to one another 2.2 L Cmean or average height of crystallites in a sam

21、ple NOTE It is expressed as a linear dimension, in nanometres. 2.3 hkl(002) Miller indices of the crystalline planes of graphite corresponding to a lattice spacing (d) of 0,335 nm 2.4 glancing angle produced when a parallel beam of uniform X-rays impinges upon a crystalline lattice and measured by t

22、he X-ray goniometer NOTE It is usually expressed in 2 . BS ISO 20203:20052 3 Principle A packed sample pulverized to less than 75 m is subjected to a monochromatic X-ray beam and rotated to produce a diffraction pattern under specific conditions. The location and shape of the peak with hkl (002) at

23、d = 0,335 nm is used to calculate L cby manual interpretation of the peak or by computer simulation. 4 Apparatus 4.1 X-ray powder diffractometer, equipped with an X-ray source set for Cu-K radiation, a monochromator or filter for restricting the wavelength range, a sample holder, a radiation detecto

24、r, a signal processor, and readout (chart or computer memory). The diffractometer shall be capable of rate scanning at 1/min or incrementally step scanning at 0,2/step. 4.2 Sample holders, as specified by the manufacturer of the diffractometer, that enable packing of a pulverized sample of sufficien

25、t height to expose a level, smooth surface to the X-ray beam. 4.3 Briquetting press, capable of generating pressures up to 70 MPa. 4.4 Compressible aluminum caps, used as a support for producing a briquetted sample. 4.5 Silicon or quartz sample, of reference material quality suitable for calibrating

26、 the diffractometer. NOTE These materials are usually available from national reference organizations e.g. the National Institute of Standards and Technology in USA. 5 Reagents and materials Use only reagents of recognized analytical grade and only distilled water or water of equivalent purity (see

27、1, 2 and 3 in the Bibliography). 5.1 Acetone. 5.2 Polyethylene glycol, approximate molecular weight of 200. 5.3 Binding agent, prepare a solution of polyethylene glycol and acetone, so that the proportion of polyethylene glycol in the solution, expressed as a mass fraction (w) by percentage of the t

28、otal composition. is 15 %, by adding 15 g of polyethylene glycol to 85 g of acetone. 6 Sample preparation 6.1 General For recommended practices for obtaining, handling and preparing coke samples, refer to ISO 6375 5 . Reduce and divide the gross sample to obtain a laboratory analysis sample. Divide,

29、 by riffling, a minimum of 100 g from the laboratory analysis sample. Crush 100 g of the test sample such that 98 % will pass through a 75 m (No. 200) sieve. 6.1.1 Any of the packing techniques listed in 6.2 may be used for packing the sample into the X-ray diffractometer specimen holder: BS ISO 202

30、03:20053 6.2 Packing techniques for X-ray diffraction specimen holder 6.2.1 Back-fill technique Put the window on a glass slide (Slide 1) and transfer sufficient quantities of sample into the window. Work the sample towards the corners of the holder using a glass slide or spatula. Press down using a

31、 flat glass slide and scrape off any excess material. Place a glass slide (Slide 2) on top of the sample and secure with tape. Remove Slide 1 to expose a flat, smooth surface before inserting into the diffractometer for analysis. 6.2.2 Front-fill technique Place a confining ring over the round sampl

32、e holder and fill the holder cavity and ring with sample. The ring will initially overfill the sample holder. Work the sample into the entire cavity and ring. Scrape the excess off with a glass plate or spatula. Press down using a flat glass slide. Remove any excess material on the front face of the

33、 holder. Repress the sample with the glass slide while turning clockwise and anticlockwise. Continue until the sample is level with the holder face. Place the sample in the diffractometer holder. 6.2.3 Side-loading technique Pack the sample. Clamp a glass slide over the top face to form a temporary

34、cavity wall. With the holder in a vertical position, drift the powdered sample into the end opening. If necessary, use a cardboard pusher cut to fit the cavity, to lightly compress the sample so it will remain in the cavity. Return the holder to a horizontal position and carefully remove the glass s

35、lide. Place the sample in the diffractometer holder. 6.2.4 Briquetting technique Weigh out 4,0 g of the sample onto a watch glass and pipette exactly 3 ml of the binding agent onto the sample and mix thoroughly with a spatula. Place the sample under an infrared-heat lamp and allow the acetone to eva

36、porate. Typically, about 1 or 2 min will be required to eliminate the acetone odour from the sample. Break up the caked sample with a spatula and transfer to an aluminum cap whose diameter is compatible with the sample holder of the diffractometer. Place the cap in a briquetting press and press at 4

37、8 MPa. Transfer the pelletized sample to the sample holder and insert into the diffractometer for analysis. 7 Calibration 7.1 Ensure that the diffractometer is in correct mechanical and optical alignment and that intensities have been maximized through the procedures described in the instrument manu

38、facturers documentation. A service engineer or in-house technician who has been well instructed in the correct alignment procedures suggested by the manufacturer best accomplishes this. 7.2 Monitor proper angles and intensities with the reference silicon or quartz sample and take corrective actions

39、if necessary. 8 Procedure 8.1 Prepare and operate the diffractometer in accordance with the manufacturers instructions. Once established, closely control all instrumental parameters to ensure repeatable analyses. 8.2 Place the packed sample in the instruments sample holder and energize the X-ray sou

40、rce. 8.3 Obtain a diffraction pattern rate scanned at 1/min or step scanned at 0,2/step over the range of 14 to 34 2 . Record the data either on a strip-chart recorder scanning at 1/min or through computer software designed to read and store the angular and intensity measurements. The measurement ti

41、me can be significantly reduced by selecting suitable segments of the range 14 to 342 . Segments are chosen to cover the required points in 9.1. BS ISO 20203:20054 9 Calculation 9.1 Manual interpretation 9.1.1 For manual interpretation from a strip-chart recording, refer to Figure 1 and 9.1.2 to 9.1

42、.5. 9.1.2 Determine the average low and high backgrounds (Points A and B, respectively) on the diffraction scan and connect them with a straight line. 9.1.3 Construct line CD parallel to line AB, and going through the apex of the peak at point G (hkl (002) at 0,335 nm. Draw the line such that, if th

43、e peak is irregular, it will pass through the average of the irregularities. Key X degree two theta (2 ) Y intensity (arbitrary unit) Figure 1 Typical diffraction scan of petroleum coke 9.1.4 Determine the full-width half maximum (FWHM) of line AB. Construct line EF such that it intersects the peak

44、at half of its maximum value. The points at which EF intersects the peak are 2 1and 2 2 , respectively. 9.1.5 For computer simulation based on the intensities recorded at 0,2 intervals, produce a mathematical representation of the diffraction curve. Determine the baseline, peak, peak height, and hal

45、f-peak height to produce the half-peak height angles, 2 1and 2 2 , as above. BS ISO 20203:20055 9.2 Determine the mean crystallite height c L () 21 0, 89 2s i n s i n c L = (1) where is the wavelength of the target material of the X-ray tube, expressed in nanometres; 1is the angle at the half-peak i

46、ntensity (2 1/2) width on the low side; 2is the angle at the half-peak intensity (2 2/2) width on the high side; 0,89 is an arbitrary constant that is equivalent to 0,89 for L C 4 . NOTE Equation 1 was derived from the Scherrer equation (Equation 2). () () 0, 89 cos c L = (2) where 0,89 is an arbitr

47、ary constant that is equivalent to 0,89 for L C ; is the wavelength of the source radiation, expressed in nanometres; is the line breadth of the pure diffraction peak, expressed in radians; is the angular location of the peak maximum (2 /2) expressed in degrees. The above equations make the assumpti

48、on that the true line width is equal to the measured width, the contribution of instrumental line broadening is negligible. 10 Reporting of results Report the mean crystallite height to the first decimal i.e. L C= x,xx nm. 11 Precision and bias 11.1 General The precision of this test method, as dete

49、rmined by the statistical examination of inter-laboratory test results in which one operator in ten laboratories made a duplicate analysis on each of six materials, is as given in 11.2 to 11.4. BS ISO 20203:20056 11.2 Repeatability The difference between successive results, by the same operator using the same apparatus under constant operating conditions on identical test materials, will, in the long run, in norma